Electrical Engineering

Yes, Kirchhoff law is applicable to linear circuits. In fact, both of Kirchhoff's

laws are applicable to ALL circuits, because they're just conservation laws.

diode

diode conducts by applying certain voltage

photo diode

photo diode conducts when it is exposed to sun light

Normally you would specify a motor to do a particular job by the mechanical power output you require.

A motor takes electrical power "in" and produces mechanical power "out".

Read whatever it says on the motor's rating plate or user-guide.

The mechanical energy output of a motor is measured in various units around the world: for example in watts, horsepower (or brake horsepower).

Another answer

The above answer is quite correct in stating that a motor's output power is its rated power as it's a guide to how much load it can drive.

Power is simply a rate - the rate of transfer of energy. The horsepower is the Imperial unit of power, whereas the watt is the SI unit of power. In the US the output power of a motor is typically still measured in horsepower whereas in Europe the use of horsepower is almost obsolete, except for small "fractional horsepower" electric motors, and both the input power and the output power of a motor are measured in watts or, more likely, kilowatts.

In a way, a capacitor is a little like a battery. Although they work in completely different ways, capacitors and batteries both store electrical energy. Inside the battery, chemical reactions produce electrons on one terminal and absorb electrons on the other terminal. A capacitor is much simpler than a battery, as it can't produce new electrons -- it only stores them. Inside the capacitor, the terminals connect to two metal plates separated by a non-conducting substance, or dielectric. You can easily make a capacitor from two pieces of aluminum foil and a piece of paper. It won't be a particularly good capacitor in terms of its storage capacity, but it will work. In theory, the dielectric can be any non-conductive substance. However, for practical applications, specific materials are used that best suit the capacitor's function. Mica, ceramic, cellulose, porcelain, Mylar, Teflon and even air are some of the non-conductive materials used. The dielectric dictates what kind of capacitor it is and for what it is best suited. Depending on the size and type of dielectric, some capacitors are better for high frequency uses, while some are better for high voltage applications. Capacitors can be manufactured to serve any purpose, from the smallest plastic capacitor in your calculator, to an ultra capacitor that can power a commuter bus. NASA uses glass capacitors to help wake up the space shuttle's circuitry and help deploy space probes. Here are some of the various types of capacitors and how they are used. Air - Often used in radio tuning circuits Mylar - Most commonly used for timer circuits like clocks, alarms and counters Glass - Good for high voltage applications Ceramic - Used for high frequency purposes like antennas, X-ray and MRI machines Super capacitor - Powers electric and hybrid cars Capacitor Circuit In an electronic circuit, a capacitor is shown like this: When you connect a capacitor to a battery, here's what happens: • The plate on the capacitor that attaches to the negative terminal of the battery accepts electrons that the battery is producing. • The plate on the capacitor that attaches to the positive terminal of the battery loses electrons to the battery. Once it's charged, the capacitor has the same voltage as the battery (1.5 volts on the battery means 1.5 volts on the capacitor). For a small capacitor, the capacity is small. But large capacitors can hold quite a bit of charge. You can find capacitors as big as soda cans that hold enough charge to light a flashlight bulb for a minute or more. Even nature shows the capacitor at work in the form of lightning. One plate is the cloud, the other plate is the ground and the lightning is the charge releasing between these two "plates." Obviously, in a capacitor that large, you can hold a huge amount of charge! Let's say you hook up a capacitor like this:
Here you have a battery, a light bulb and a capacitor. If the capacitor is pretty big, what you will notice is that, when you connect the battery, the light bulb will light up as current flows from the battery to the capacitor to charge it up. The bulb will get progressively dimmer and finally go out once the capacitor reaches its capacity. If you then remove the battery and replace it with a wire, current will flow from one plate of the capacitor to the other. The bulb will light initially and then dim as the capacitor discharges, until it is completely out. Farad A capacitor's storage potential, or capacitance, is measured in units called farads. A 1-farad capacitor can store one coulomb (coo-lomb) of charge at 1 volt. A coulomb is 6.25e18 (6.25 * 10^18, or 6.25 billion billion) electrons. One amprepresents a rate of electron flow of 1 coulomb of electrons per second, so a 1-farad capacitor can hold 1 amp-second of electrons at 1 volt. A 1-farad capacitor would typically be pretty big. It might be as big as a can of tuna or a 1-liter soda bottle, depending on the voltage it can handle. For this reason, capacitors are typically measured in microfarads (millionths of a farad). To get some perspective on how big a farad is, think about this: • A standard alkaline AA battery holds about 2.8 amp-hours. • That means that a AA battery can produce 2.8 amps for an hour at 1.5 volts (about 4.2 watt-hours -- a AA battery can light a 4-watt bulb for a little more than an hour). • Let's call it 1 volt to make the math easier. To store one AA battery's energy in a capacitor, you would need 3,600 * 2.8 = 10,080 farads to hold it, because an amp-hour is 3,600 amp-seconds. If it takes something the size of a can of tuna to hold a farad, then 10,080 farads is going to take up a LOT more space than a single AA battery! Obviously, it's impractical to use capacitors to store any significant amount of power unless you do it at a high voltage. Applications The difference between a capacitor and a battery is that a capacitor can dump its entire charge in a tiny fraction of a second, where a battery would take minutes to completely discharge. That's why the electronic flash on a camera uses a capacitor -- the battery charges up the flash's capacitor over several seconds, and then the capacitor dumps the full charge into the flash tube almost instantly. This can make a large, charged capacitor extremely dangerous -- flash units and TVs have warnings about opening them up for this reason. They contain big capacitors that can, potentially, kill you with the charge they contain. Capacitors are used in several different ways in electronic circuits: • Sometimes, capacitors are used to store charge for high-speed use. That's what a flash does. Big lasersuse this technique as well to get very bright, instantaneous flashes. • Capacitors can also eliminate ripples. If a line carrying DC voltage has ripples or spikes in it, a big capacitor can even out the voltage by absorbing the peaks and filling in the valleys. • A capacitor can block DC voltage. If you hook a small capacitor to a battery, then no current will flow between the poles of the battery once the capacitor charges. However, any alternating current (AC) signal flows through a capacitor unimpeded. That's because the capacitor will charge and discharge as the alternating current fluctuates, making it appear that the alternating current is flowing.