answersLogoWhite

0

📱

Electronics Engineering

Electronics Engineering is a branch of engineering that deals with practical applications of electronic components, devices, systems, or equipment. Electronics are devices that operate on low voltage sources, as in electron tubes, transistors, integrated circuits, and printed circuit boards and use electricity as part of its driving force.

24,372 Questions

What is the voltage requirement for 1 yellow LED?

A: Usually LEDS are 1.8v but this varies from color to color and size. When a LED is bought that is when the voltage is current must be evident otherwise you need a VOM and a 9v battery and some resistors to find the voltage.

Does turning a DC motor on and off affect the life of the motor?

Turning something on and off shortens the life of one or more components in any circuit. In the case of a motor the start current is increased over run current so that every time you start the motor that start up current is imposed on the motor. Over time the higher current can melt the covering of the motor winding or weaken the structure of parts carrying the current. The quality f the individual parts will determine how much the life of the motor is reduced. There are also mechanical affects that may shorten life like the contact between rotor and stator.

Why is The voltage across the empty socket is equal to the line voltage?

all the sockets are always connected in parallel,due to this the voltage across each soket is same. when any socket is open then there is no voltage loss..so the votage is same like line voltage.

Carbon nanotube structure?

carbons that are covelently bonded together in hexagonal form to make a thin tube as strong as diamonds, lighter then steal and as thin as a human hair strand

Calculate the energy delivered by 20V battery to a capacitor of capacitance 10uF?

the formula for energy stored in a capacitor is (1/2)*cv^2

given v=20v,

c =10*10^-6 f

by using this information you can easily calculate the energy

Was cell phones invented in the 1970's?

In the 1970s there were no cell phones, but there were mobile radio phones. These were bulky, required going through an operator, and only worked in large cities. The detective Cannon on the TV show of the same name had one in his car.

What can you break without hitting or dropping?

anything! u can slice, rip, or bend basicl anything. like a baseball....u can rip it apart if u just use a knife

What is 75 ohm?

Ohms are a measure of resistance to electric current.

You're probably talking about a 75 ohm coaxial cable. In this case, 75 ohms is the characteristic impedance of the cable.

Sony ericsson p1i Full formate code?

The option for formatting the External Drive or the memory card is prestty simple and can also be done by connecting the same to one of the Computers. The Important part - Formatting the Internal Disk - Using the Jog Dial - Jog Dial - UP * Down Down * Down * This would give you an option to format the Internal Disk. **Please do this at your own RISK.

What is diode clamping?

There are a couple types of diode clamping-- A P-N diode was often used for clamping coils of relays that produce high voltages when the relays is de-energized. Bidirectional zeners are now the best solution. Diode clamping is also a term used to limit voltage excursions generally. Zener diodes are generally used for this purpose.

How can you present one image in a 4 TVs screen by distribute the image in to 4 corner?

This application generally requires some sort of video processor. The process is image scaling and it allows the zooming in of a portion of an image on one of 4 screens. Basically this is known as video wall processing. Solutions can be found at

Jupiter systems

RGB Spectrum

Aurora Multimedia

Avertech

TVOne

Many commercial TVs have processors built-in.

Relation between current gain and collector current?

That's referred to as, `hfe` in transistor parlance. Essentially, since a transistor is a current operated device, the gain means that for every milliamp in at the base, the gain (times X) will be amplified through the junction of the collector/emitter.

For instance, take a transistor with a gain of 30. One milliamp in at the base will allow the transistor to pass 30 milliamps through the collector/emitter junction. Of course, there will also be a resultant voltage drop of 1.2 volts over all. -.6 volts for the base and -.6 volts through the collector/emitter junction. Remember, you're working with a current controlled device, and not a voltage controlled device like an op-amp.

How the data transmission occurs through crossover cable connection?

A crossover cable connects two computers without going through a switch. The data transmission happens just like in a switched environment. You still have to have a network client with viable addresses, and they have to be the same format, such as same subnet mask and default gateway.

What extrinsic semiconductor is?

Those semiconductors in which some impurity atoms are embedded are known as extrinsic semiconductors.

Why must the air inside a waveguide be dehumidified?

Moisture in the air in a waveguide can scatter the microwave energy the waveguide is designed to transport. This translates into signal loss or attenuation. The VSWR drops, and that is not a good thing.

Does your supervisor cooperate with you in the fulfillment of your responsibilities?

It depends on the particular supervisor. In an ideal situation, yes, the supervisor cooperates with the worker in order to help the worker achieve their goals.

What is the significance of high impedance state in tri-state gates?

This is a state that disconnects the gate from the line it drives so that another gate can connect to it and drive it instead. This permits sharing so that multiple sources can drive common lines without fighting and/or damaging each other.