Ford Expedition

No, the third-row seats in the Ford Excursion and Ford Expedition are not the same. The Ford Excursion, being a larger SUV designed for more passenger and cargo space, features a different seat configuration and design compared to the Expedition. While both vehicles may share some design elements, the dimensions and mounting points of the third-row seats differ due to their size and intended use.

The code P1132 for a 1997 Ford Expedition indicates a problem with the air-fuel mixture, specifically relating to the oxygen sensor readings. It typically means that the engine control module (ECM) is detecting a lean condition, where there may be too much air or not enough fuel in the combustion chamber. This could be caused by issues such as a vacuum leak, faulty fuel injectors, or a malfunctioning mass airflow sensor. Addressing this code often involves inspecting the fuel system and related components to ensure proper operation.

To open or close the side rear window on a 2013 Ford Expedition, locate the window control switch on the rear door panel. Press the switch down to open the window and lift it up to close. If the vehicle is equipped with a child safety lock, ensure it is disengaged for access. Always ensure the area around the window is clear before operating it.

To remove the back brakes on a 1998 Ford Expedition, you'll typically need a T45 Torx bit. This size is used for the caliper bracket bolts. Always ensure you have the proper tools and follow safe practices when working on your vehicle's braking system.

The fuel pressure for a 2004 Ford Expedition typically ranges from 30 to 40 psi (pounds per square inch) when the engine is running. It's important to check the specifications for your specific engine type, as there may be slight variations. If you're experiencing fuel pressure issues, it's advisable to consult the vehicle's service manual or a professional mechanic for accurate diagnostics.

The Bartleson-Bidwell Expedition, which aimed to settle in California, concluded in November 1841. The group, consisting of approximately 80 members, faced numerous challenges during their journey, including harsh weather and difficult terrain. Ultimately, they reached their destination in California, marking one of the early overland migrations to the region.

To reset the mileage on a replacement instrument cluster for a 2004 Isuzu Ascender, you typically need to access the vehicle's diagnostic system using a specialized scan tool. This tool allows you to reprogram the mileage to match the original cluster or set it to the correct value. Alternatively, some clusters may require a manual adjustment procedure, which can involve specific button sequences or settings. It's important to consult the vehicle's service manual or a professional technician for the exact steps, as procedures can vary.

Yes, a disconnected vacuum hose on a pressure regulator will generally lead to an increase in fuel pressure. The vacuum hose helps regulate fuel pressure based on the engine's load and demand; when it's disconnected, the regulator may not receive the necessary vacuum signal, causing it to maintain a higher pressure. This can result in poor engine performance, increased fuel consumption, and potential damage to the engine or fuel system components.

When the 4x4 light blinks on a 1999 Ford Expedition, it typically indicates that there is a problem with the 4WD (four-wheel drive) system. This could be due to issues such as a malfunctioning transfer case, a faulty switch, or problems with the electronic control system. It's advisable to consult the vehicle's owner manual and consider having a professional mechanic diagnose the issue to ensure safe operation.

The fuel shut-off switch on a 1999 Mitsubishi Diamante is typically located in the trunk, near the rear passenger side. It may be mounted on the side panel or near the fuel pump access point. To reset it, you may need to press the button on the switch after a significant impact or in the event of a fuel-related issue. Always consult the owner's manual for the exact location and instructions.

To replace the wiper switch on a 2003 Ford Expedition, first disconnect the negative battery cable to ensure safety. Remove the steering column cover by taking out the screws, and then detach the wiper switch by unplugging the electrical connector and removing any retaining screws. Install the new wiper switch by reversing the disassembly steps, reconnect the battery, and test the switch to ensure proper functionality.

A 2001 Ford Expedition typically holds about 12 to 14 quarts of transmission fluid when including the torque converter and the transmission cooler. However, if you're only changing the fluid and not the filter or performing a complete flush, you may need around 5 to 7 quarts. Always check the owner's manual or consult a professional for the most accurate information specific to your vehicle.

The 1999 Eddie Bauer Ford Expedition typically has a bolt lug pattern of 5x135 mm. This means it has five bolt holes arranged in a circle with a diameter of 135 mm. It’s important to ensure that any replacement wheels match this specification for proper fit and safety.

To replace the front brake pads on a 2002 Ford Expedition, first, lift the vehicle and remove the front wheels. Then, locate the brake caliper, unbolt it, and carefully slide it off the brake rotor. Remove the old brake pads from the caliper bracket and compress the caliper piston using a C-clamp or brake tool before installing the new pads. Reassemble the caliper, ensuring everything is properly secured, and then reattach the wheels and lower the vehicle.

When towing a boat with a 1999 Ford Expedition, you should typically use a lower gear to enhance control and power, especially when starting from a stop or climbing hills. It's advisable to use "Tow/Haul" mode if equipped, as this optimizes the transmission for towing. Generally, aim for a gear that allows the engine to maintain a steady RPM without over-revving, ensuring safe and efficient towing. Always refer to the owner's manual for specific recommendations based on your towing setup.

To install the power door lock relay in a 2000 Ford Expedition, first, disconnect the negative battery cable to ensure safety. Locate the relay, which is typically found in the fuse box under the dashboard or in the engine compartment. Remove the old relay by gently pulling it out of its socket and insert the new relay in the same position. Finally, reconnect the battery cable and test the power door locks to ensure proper functionality.

The oil capacity for a 2005 Ford Expedition equipped with a 5.4-liter V8 engine is approximately 6 quarts (5.7 liters) when using a standard oil filter. If using a larger filter, the capacity may increase slightly. Always consult the owner's manual for the most accurate specifications and recommendations for oil type.

The difference between 650 and 750 cold cranking amps (CCA) in a Ford Expedition pertains to the battery's ability to start the engine in cold temperatures. A battery with 750 CCA can deliver more power to the starter motor than one with 650 CCA, making it more effective in colder conditions. This increased power can lead to more reliable starts, particularly in frigid weather. However, if the vehicle is primarily used in milder climates, the 650 CCA battery may suffice.

The Mier Expedition, which took place in 1842, was primarily driven by the desire of Texan adventurers to retaliate against Mexico for previous raids and conflicts, particularly after the Mexican army's incursion into Texas. It was also fueled by ambitions of expansion and the belief in Manifest Destiny, aiming to assert Texan influence over Mexican territory. The expedition ultimately ended in disaster, as the Texan forces were captured and faced harsh consequences.

Codes P0171 and P0174 indicate that the engine is running lean on both the bank 1 and bank 2 sides, respectively. Common causes include a vacuum leak, such as a cracked or disconnected hose, a dirty or failing mass air flow (MAF) sensor, or issues with the fuel system, such as a clogged fuel filter or weak fuel pump. Additionally, problems with the oxygen sensors can also lead to these codes. It's important to diagnose the specific cause to ensure proper repairs are made.

If your Ford Expedition's courtesy lights won't turn off, it could be due to a faulty door switch that thinks a door is still open. Additionally, there might be an issue with the vehicle's lighting control module or a malfunctioning timer. Checking the position of all doors and ensuring they are securely closed can help. If the problem persists, it may require further inspection by a mechanic.

On a 2000 Ford Expedition, Bank 2 Sensor 2 is located on the exhaust system, specifically on the passenger side, after the catalytic converter. It is positioned further downstream compared to Bank 2 Sensor 1, which is before the catalytic converter. To access it, you may need to raise the vehicle for better visibility and reach.

Sacagawea was with the Lewis and Clark Expedition for its entire duration, which lasted from May 1804 to September 1806. She joined the expedition as a guide and interpreter, playing a crucial role in facilitating communication and navigating the terrain. Her presence helped ensure the group's success in reaching the Pacific Ocean and returning safely.

I don't have the ability to provide images or diagrams. However, you can find a diagram of the EGR valve for a 2002 Ford Expedition in the vehicle's service manual or by searching online through automotive forums or repair websites. These resources often offer detailed diagrams and installation guides for specific components.

To replace the driver's side mirror on a 1999 Chevy Malibu, first, ensure the vehicle is turned off and disconnect the negative battery terminal. Remove the interior door panel by unscrewing any visible screws and gently prying off the panel clips. Disconnect the electrical connector for the mirror, then remove the mounting bolts securing the mirror to the door. Finally, install the new mirror by reversing the steps: attach the new mirror, reconnect the electrical connector, and reassemble the door panel.