Honda ATVs

To check the oil in a Honda Rincon, first ensure the ATV is on a level surface and the engine is off. Remove the dipstick from the oil filler cap, wipe it clean, then reinsert it without screwing it in to check the oil level. The oil should be between the upper and lower marks on the dipstick. If necessary, add the appropriate oil through the filler cap to reach the correct level.

The rear axle of a Honda 350 ATV typically uses a gear oil, specifically a hypoid gear oil with a viscosity rating of 80W-90 or 75W-90. It's important to consult the owner’s manual for the specific model, as recommendations may vary slightly. Ensure that the oil meets the API GL-5 specification for optimal performance and protection.

The 2011 Honda Rincon 675 has a horsepower rating of approximately 50 horsepower. This ATV is powered by a liquid-cooled, 675cc single-cylinder engine, which provides a good balance of power and efficiency for both recreational and utility purposes. Its performance is complemented by a smooth automatic transmission and a durable drivetrain.

To change the headlight on a Honda FourTrax 300, first, ensure the vehicle is turned off and the battery is disconnected for safety. Remove the headlight assembly by unscrewing the retaining screws or clips that hold it in place. Carefully detach the old headlight bulb from its socket and replace it with a new one, making sure it’s securely connected. Finally, reassemble the headlight assembly and reconnect the battery before testing the new bulb.

To fix the kick start on a 1986 Honda 250 Big Red, first inspect the kick starter mechanism for any damage or wear. Check the kick starter spring and return mechanism to ensure they are functioning properly. If the kick start is not engaging, you may need to disassemble the side cover to examine the gears and replace any worn parts. Finally, lubricate all moving components and reassemble to ensure smooth operation.

To get a Honda FourTrax out of gear, ensure the vehicle is in neutral by pressing the neutral indicator button or checking the gear display. If it’s stuck, try pulling in the clutch lever fully while gently rocking the machine back and forth. If needed, you can also turn the ignition off and restart to reset the transmission. Always refer to the owner’s manual for specific guidance related to your model.

If your 1988 Honda FourTrax 300 only idles with the choke on, it likely indicates a fuel delivery issue, such as a clogged carburetor jet or air filter. The choke enriches the fuel mixture, compensating for insufficient fuel reaching the engine. Additionally, there could be a vacuum leak or an issue with the fuel system, such as a bad fuel pump or fuel line obstruction. Cleaning the carburetor and checking for air leaks are good first steps to diagnose the issue.

The oil filter on a Honda TRX 250 ATV is typically located on the right side of the engine, near the bottom. It is a round, metal canister that can be accessed from the side of the ATV. To replace it, you'll need to remove the old filter using an oil filter wrench and install the new one after draining the old oil. Always consult the owner's manual for specific instructions and maintenance tips.

To change the bearing on the left axle of a Honda FourTrax 250, first, remove the wheel and brake assembly to access the axle. Next, detach the axle from the differential by removing the retaining clips and any securing bolts. Carefully pull the axle out, replace the old bearing with a new one, and ensure it is properly seated. Finally, reassemble the axle, brake assembly, and wheel, making sure everything is secured correctly.

To reset the oil change notification on a 2003 Honda ATV, first turn on the ignition without starting the engine. Then, press and hold the "reset" button (or the "mode" button, depending on the model) until the oil change indicator blinks and then disappears. This process typically takes a few seconds. Finally, turn off the ignition to complete the reset.

For a 2003 Honda Rincon 650, it's recommended to use a high-quality gear oil with a viscosity of 80W-90. Ensure that the oil meets API GL-4 or GL-5 specifications for optimal performance. Always refer to the owner’s manual for specific recommendations and to maintain the vehicle's warranty and longevity.

To add oil to a Honda Rancher ATV, locate the oil filler cap, which is typically found on the engine's side. Ensure the ATV is on a level surface, then remove the cap and use a funnel to pour in the recommended oil type. After adding oil, check the dipstick to ensure the oil level is within the specified range before replacing the cap. Always refer to the owner’s manual for specific oil types and capacities.

To remove the starter from a 1986 Honda Fourtrax 350, first disconnect the negative battery cable to ensure safety. Then, locate and remove the bolts securing the starter to the engine, usually found on the side of the motor. Carefully disconnect the electrical connections, including the starter solenoid wire, before pulling the starter out. Finally, check for any mounting brackets or additional components that may also need to be removed.

The wheelbase of the Honda CB400 Super Four, a popular motorcycle model, is approximately 1,405 mm (55.3 inches). This dimension contributes to the bike's stability and handling characteristics, making it suitable for both urban commuting and spirited rides. Different variants of the CB400 may have slight variations in wheelbase, but it generally remains within a similar range.

The valve clearance for a 1987 Honda Fourtrax 4x4 (TRX350) is typically set at 0.004 inches (0.1 mm) for both intake and exhaust valves when the engine is cold. It's important to adjust the valve clearance periodically to ensure optimal engine performance and prevent potential damage. Always consult the owner's manual or a service manual for specific guidelines and procedures.

If your 1985 Honda 250R ATC keeps blowing headlight bulbs, it could be due to several reasons. Common causes include a faulty voltage regulator that allows excess voltage to reach the bulbs, poor wiring connections leading to short circuits, or using bulbs with a higher wattage than recommended. Additionally, a damaged stator or electrical components can also contribute to the issue. It's best to check the electrical system for any signs of wear or malfunction.

The value of a used 1999 Honda FourTrax 4-wheeler typically ranges from $1,500 to $3,000, depending on its condition, mileage, and any modifications or upgrades. Factors such as location and demand can also influence the price. It's advisable to check local listings and resources like Kelley Blue Book for a more accurate valuation.

The 2012 Honda Rancher typically requires about 2.5 quarts of oil when using a standard oil filter during an oil change. If you're not replacing the oil filter, it usually needs around 2.0 quarts. It's important to use the recommended oil type, which is generally 10W-40 for most conditions. Always check the owner's manual for specific recommendations and maintain proper levels for optimal performance.

Yes, it is possible to rebuild a water pump for a Honda Rincon 650. The process typically involves disassembling the pump, replacing worn or damaged components such as seals, bearings, and impellers, and then reassembling it with proper torque specifications. It's important to have the right tools and follow a detailed service manual for guidance. If you're not experienced, seeking help from a professional mechanic is advisable.

For the 1994 Honda Fourtrax 300 4x4, the valve adjustment procedure involves first removing the valve cover. The proper valve clearance specification for both the intake and exhaust valves is typically 0.05 mm (0.002 in) when the engine is cold. Adjust the clearance by turning the adjusting screw while holding it in place with a wrench. Once adjusted, recheck the clearance to ensure it is within the specified range before reassembling the valve cover.

The 1989 Honda FourTrax 250 ATV typically has a top speed of around 45 to 50 miles per hour (72 to 80 kilometers per hour). This speed can vary depending on factors such as the condition of the ATV, terrain, and rider weight. Its design prioritizes utility and reliability over high-speed performance, making it suitable for various off-road tasks.

A Honda FourTrax typically requires a high-quality gear oil that meets the specifications outlined in the owner's manual. Most models recommend using a 10W-40 or 80W-90 gear oil, specifically designed for hypoid gear applications. It's essential to choose an oil that is API GL-4 or GL-5 rated. Always check the specific model's manual for the exact requirements, as recommendations may vary.

To bleed the front brakes on a Honda Rancher, start by ensuring the brake fluid reservoir is filled to the appropriate level. Then, locate the brake bleeder valve on the front brake caliper. Using a wrench, loosen the bleeder valve slightly while having an assistant pump the brake lever several times, then hold the lever down; tighten the bleeder valve before releasing the lever. Repeat this process until you see clear fluid without air bubbles, and ensure to check and top off the brake fluid as needed during the procedure.

The top speed of a Honda Foreman 450 is typically around 45 to 50 miles per hour, depending on factors such as terrain, rider weight, and modifications. This ATV is designed for utility and off-road performance rather than high speed, prioritizing torque and stability over sheer velocity.

The oil capacity of a 1986 Honda Fourtrax 125 is approximately 1.5 quarts (or about 1.4 liters) when including the oil filter change. The recommended oil type is SAE 10W-40, which is suitable for a variety of temperatures and conditions. It's important to use a high-quality motorcycle or ATV oil to ensure optimal engine performance and longevity.