Honda ATVs

The Honda Rancher typically has a horsepower range of about 24 to 30 horsepower, depending on the specific model and engine configuration. The Rancher is available in different variants, including 2WD and 4WD options, which may slightly affect the power output. For the most accurate information, it's best to check the specifications of the exact model year you are interested in.

To change the oil and oil filter on a Honda ATV 500 Rubicon, start by warming up the engine slightly to thin the oil, then turn it off and allow it to cool. Place a drain pan under the oil drain plug, remove the plug, and let the oil drain completely. Next, replace the oil filter using an oil filter wrench, making sure to lubricate the rubber gasket on the new filter with a bit of fresh oil. Finally, replace the drain plug, refill the engine with the recommended oil through the dipstick tube, and check the oil level to ensure it’s within the proper range.

The Honda Rancher ATV typically uses a sealed lead-acid (SLA) battery, specifically a 12V battery. The exact model may vary depending on the year and specific model of the Rancher. It's important to check the owner's manual or specifications for the exact battery type and size required for maintenance or replacement.

The fuel capacity of a Honda ATV varies by model, but most Honda ATVs typically hold between 2 to 5 gallons of fuel. For example, the Honda FourTrax Rancher has a fuel capacity of about 3.9 gallons. It's always best to check the specific model's specifications for precise information.

To set the timing on a 1987 Honda FourTrax 350 ATV, first ensure the engine is off and cool. Remove the timing inspection cover and locate the timing mark on the flywheel, then align it with the mark on the engine case while rotating the crankshaft. Adjust the timing by loosening the stator bolts and rotating the stator until the timing marks align, then tighten the bolts securely. Finally, replace the inspection cover and start the engine to check for proper timing.

For the 1994 Honda FourTrax 300 4x4, the valve clearance settings are typically 0.004-0.006 inches (0.10-0.15 mm) for the intake valves and 0.006-0.008 inches (0.15-0.20 mm) for the exhaust valves. The torque specifications for the cylinder head bolts are usually around 16 lb-ft (22 Nm). Always consult the specific service manual for your vehicle to ensure accuracy and proper maintenance.

On a 2003 Honda FourTrax 350, the positive battery cable connects to the positive terminal of the battery. From there, it typically runs to the starter motor and may also connect to the main fuse and other electrical components. Ensure that the connection is clean and secure to maintain proper electrical function.

To tighten the chain on a 1987 Honda FourTrax, first, place the ATV on a level surface and elevate the rear with a stand. Loosen the axle nut and the two lock nuts on the chain adjuster bolts. Turn the adjuster bolts evenly on both sides to achieve the desired chain tension, ensuring the chain has approximately 1 to 1.5 inches of slack. Once adjusted, re-tighten the lock nuts and axle nut securely.

The value of a Honda ATV 500 Rubicon can vary based on factors such as its age, condition, mileage, and location. Generally, used models range from approximately $5,000 to $8,000. For the most accurate estimate, it's best to check local listings, dealerships, or online marketplaces for current pricing in your area.

For a 1996 Honda 300 4x4 ATV, it is recommended to use 10W-40, four-stroke engine oil that meets the JASO MA specification. Synthetic or conventional oils are both acceptable, but synthetic oil may provide better performance and protection. Always check the owner's manual for any specific recommendations or requirements for oil changes and maintenance.

To change the headlight on a 1999 Honda Foreman 4-wheeler, first, ensure the vehicle is turned off and the key is removed. Remove the headlight's plastic cover by unscrewing or unclipping it, then disconnect the wiring harness from the back of the headlight bulb. Replace the old bulb with a new one, reconnect the wiring harness, and reattach the cover securely. Finally, test the headlight to ensure it functions properly.

On a Honda Rancher 420, the fuel filter is typically located in the fuel line, just before the carburetor or fuel injection system. You may need to remove the side panel or access the undercarriage to reach it. It's important to consult your owner's manual for the exact location and recommended maintenance procedures.

To change a front tire on a Honda ATV 250R, first, ensure the ATV is on a stable surface and secure it with a jack or lift. Remove the wheel by loosening the lug nuts with a wrench, then take off the tire. Place the new tire onto the wheel hub, tighten the lug nuts by hand, and then use the wrench to securely fasten them in a crisscross pattern. Finally, lower the ATV and ensure the tire is properly mounted and inflated to the recommended pressure.

To change the oil on a 2004 Honda Rincon ATV, first, warm up the engine slightly to thin the oil, making it easier to drain. Then, turn off the engine and place the ATV on a level surface. Remove the oil drain plug located at the bottom of the engine and allow the oil to fully drain into a container. Replace the drain plug, fill the engine with new oil through the dipstick tube using the recommended oil type, and check the oil level to ensure it’s within the proper range.

Yes, you can adjust the plastic float on a 1984 Honda Big Red, which is part of the fuel system. To do this, you'll typically need to access the carburetor, where the float is located. Adjusting the float height involves bending the float tab to ensure it opens and closes at the correct fuel level. Always consult the service manual for specific instructions and to avoid damaging the float or carburetor.

The Honda Rincon typically uses a 1157 tail light bulb. This dual-filament bulb serves both the running light and brake light functions. However, it's always a good idea to check your specific model year and owner's manual for confirmation, as bulb specifications can vary.

Your 2003 Honda Rancher may be flooding due to several reasons, such as a faulty carburetor, a malfunctioning fuel shut-off valve, or a clogged air filter. If the carburetor is not functioning properly, it can cause excessive fuel to enter the engine, leading to flooding. Additionally, if the fuel line has leaks or the fuel is contaminated, it can also contribute to the problem. Checking and cleaning the carburetor, inspecting the fuel system, and ensuring proper air intake can help resolve the flooding issue.

The timing cover on a Honda Rancher is located on the right side of the engine, typically near the front. It is a protective cover that houses the timing chain or belt, which connects the crankshaft to the camshaft. To access it, you may need to remove other components, such as the side panels or other engine covers, depending on the model year. Always consult the owner's manual for specific instructions related to your Rancher model.

The torque specifications for a Honda Rancher 400 can vary depending on the specific component being serviced. Generally, for engine components like cylinder head bolts, the torque specification is approximately 22-25 ft-lbs. For other parts, such as axle nuts or suspension components, the specifications may differ. Always refer to the owner's manual or a service manual for the exact torque values for the specific model and year.

The value of a 2003 Honda Rubicon typically ranges from $3,000 to $5,000, depending on factors such as condition, mileage, and any modifications or accessories. To get a more accurate estimate, it’s best to check listings on platforms like Kelley Blue Book or local classifieds. Always consider the specific condition and maintenance history of the vehicle when determining its value.

On a 1997 Honda FourTrax, the oil drain plug is located at the bottom of the engine, typically on the left side. It is a large hex bolt, usually requiring a socket or wrench for removal. Before draining the oil, make sure the ATV is on a level surface and the engine is warm to ensure proper drainage. Always check your owner's manual for specific details and torque specifications.

The Honda Rincon typically has a compression ratio of 9.2:1 for its 675cc engine. However, the specific compression measured in pounds per square inch (psi) can vary based on engine condition and maintenance. Generally, a healthy engine might have a compression reading around 150-180 psi. For precise specifications, it's best to consult the owner's manual or a service guide.

The 1985 Honda ATV 250 typically does not have a dedicated fuseable link or fuse for the electric start and lights. Instead, these components are usually protected by a main fuse located in the wiring harness. If you're experiencing issues with the electric start or lights, it's advisable to check this main fuse and the wiring connections for any damage or corrosion.

The fuse box on a 1997 Honda Rancher is typically located under the front fender, near the battery. To access it, you may need to remove a few screws or bolts to lift the fender or panel. It's usually a rectangular box with a cover that can be opened to check or replace fuses. Always refer to the owner's manual for specific details and diagrams.

The 2005 Honda Rincon 650 typically uses SAE 10W-40 motor oil, which is suitable for high-temperature conditions and offers good protection for the engine. It's important to use an oil that meets API service classification SG or higher. Always check the owner's manual for specific recommendations and ensure the oil is suitable for the riding conditions you expect.