0
Honda CR-V
The Honda CR-V is a crossover SUV built by Honda from 1995 to the present. The car was based on the Honda Civic design to meet the public demand for a SUV from Honda.
2,834 Questions
Will 5-30 wt oil effect the performance of your Honda crv 4 cylinder engine?
No. As a matter of fact that is the weight that's recommended for vehicles operated in a cold to hot 4-season climate.
Is it possible that your idle speed is simply set too low? When you put the car in gear and back up slowly, without giving it gas - and then turn the wheel - you are activating the power steering pump - which puts a demand on the engine's power - which COULD be enough to stall it - if the RPM's were set too low.
How do you replace rear brake shoes 2000 Honda CR-V?
Before you even decide to change your brake shoes, look at the way its put together, I suggest you take a few pictures of the braking system where the shoes will go, once you have done that, start taking the spring off that is on the right of the right shoe and place it down beside you make sure what you are taking off first will go on last, be very careful not to pinch the cylinder head if you pinch that you can cause brake fluid to come out and then you will have to bleed that brake, you will need a few different tools to do the job if you don't have all the tools I do not recommend you try to change the brake shoes but if you are a handy man this should not be much of an issue but be careful, some of the spring have a lot of tension, once you have all the parts off and in order beside you start cleaning the area with brake cleaner that will help with the process of getting everything back together, before you put the shoes on can can put anti seize compound where the shoes touch the rear of the housing so that it don't rust or seize, you will have to adjust the adjusting rod which is the one that has a little nut that moves to adjust the brakes you will have to move that all the back to the beginning, next open your hod of the car and open the brake fluid cap, if you have it topped past full you will need to keep an eye on it because once you start putting the brake shoes on and adjusted them the fluid will come out of the master cylinder, if that happens you will a turkey baster or something to suck out the brake fluid, or you can instead of that bleed the brakes, there is a bleeder screw behind the braking system to bleed that side, if you do that then you will have a better time to replace the brake fluid in the master cylinder, once you have all the part in you will have to put back the drum, if the drum does not fit or having getting stuff, you will have to again adjust it so that the drum can fit but make sure when you put the drum on that its not rubbing against the drum make sure you can turn the drum with out any friction once you have done that, close the master cylinder that is under the hood turn on your ignition just once and just tap your brake but just a little if the brake peddle goes all the way to the floor you will need to do 2 things, 1 adjust the brakes and 2 bleed that side, it can be a pain at times but with a little time and please take your time it will all work out.....
Where is the thermostat located on a 1999 Honda CR-V?
If you follow the lower radiater hose it will connect to the thermostat housing. Remove the 2 - 10mm bolts on the housing and it will reveal the thermostat.
Does the 2005 Honda CR-V have a timing chain?
yes! Starting in 2002 Honda Cr-v's switched from a 2.0L engine to a 2.4L engine. 2.0 has a timing belt 2.4 has a timing chain
Where is the transmission dipstick located on a 99 Honda CRV?
The Transmission dipstick for a 1999 Honda CRV is located under the hood of the car. It is just below the air intake, and usually has a yellow or red cap.
Is a Honda CR - V have on demand 4 wheel drive?
ONLY the 4WD models. To check to see if yours is 4WD or 2WD - look under the rear of the vehicle, If you can see a driveshaft coming from the front of the vehicle and operating a differential on the rear axle then you DO have 4WD. If by "on-demand" you mean that YOU can engage it or dis-engage it at YOUR discretion - no. The 4WD engages and disengages automatically as wheel slippage is "sensed" by the transmission and the onboard computer.
Where is the oil filter located on a 1999 Honda HR-V?
It's on the left rear of the engine above the axle. You can get to it without ramps if you crank the wheel all the way to the left. You reach through and grab onto it with your hand. If it's too tight or too greasy, use a piece of sandpaper or a rubber kitchen glove for grip.
What kind of replaceable belts does a 2004 Honda CR-V have?
The accessory drive belt and the timing belt.
What would be a reasonable cost to have an oil pan gasket replaced on a '97 Honda CRV?
Hi, I am also searching for such answer. My 97 crv keeps leaking oil from the engine. 2 days ago I have an oil changed in a local mechanic shop. They noticed the problem too and I was quoted $260 for fixing it by changing a new valve cover gasket, oil pan gasket and a drain plug, of course, including labor charge. I didn't expect to pay close to $300 to solve this problem in a regular oil change visit. So I took the checklist they gave me and quoted the price for the parts I need from Autoadvance, end up to be $140 something. With the help of my friend who loves fixing car, hopefully this is all I need to pay to fix the oil leaking.
2) I had my oil pan gasket replaced in Long Beach, CA in December of '06. The oil pan gasket cost $10, if purchased from an after market auto parts store, the repair shop charged $25. It was $100 for the labor and that was after haggling them down to that amount. I too was shocked it was going to be so much to have it replaced.
3) I just spent 5 hours changing out the oil pan gasket on my '84 Landcrusier. I have to say that it was a terrible experience. Pay the $100 dollars! It will be well worth it. I'll give you a run down: 1. Drain the oil (easy) 2. pull the oil pan off (not so easy) 3. Clean the oil pan gasket area from the pan and the engine block (easy but time consuming) 4. Put sealant on the engine block and hold the gasket up to the block until it holds (not so easy) 5. Put sealant on the oil pan and mount (you'll swear alot on this step) 6. Put all the bolts back in and torque to spec (not so easy unless you have an unrestricted path to the bolts) 7. Drink alcohol to unwind.
4)I replaced a valve cover gasket on a 1996 Honda Odyssey which would be the equivalent job as on a 97 CRV. It is about the easiest gasket job you can do for this vehicle. A rubber gasket should not cost more than $25-$35 at a local auto parts store. They are simple to install since you do not use any sealant with this type. You just remove the bolts and gently pry it off. Clean up the mating surfaces really good. Line up the new gasket and valve cover then put the bolts back in and torque them to specs. It's an hour job with clean up for a DIY. I've not done the oil pan gasket but have looked at it under a 1998 CRV. This looks a little bit harder since you have the engine shield to remove and the exhaust pipe runs right over it and very close. I think $100 is reasonable to do the oil pan gasket. If you do it yourself I recommend getting silicon gasket maker. It will make the job much easier. You just put a bead of it on both mating surfaces, let a skin form then mate them. Lightly tighten them down but not all the way. Let set for 12 hours then tighten down the rest of the way.
What size to replace wiper blades in 2002 Honda crv?
honda crv 1997 rear wiper blade should be 11", 13" is too big
Does a 2006 Honda CR-V have a timing belt or timing chain?
Not sure if European crv is different but my north American 2006 crv has 2.4L Gasoline engine with timing chain. I asked at the dealer about replacing it and water pump but i was told that both are designed to last the life time of the vehicle. my 3.5 cents...
How do you release parking brake on 2000 Honda CR-V that is stuck?
Try http://hondatech.info/downloads/Auto for free downloads of Honda Service Manuals and Diagrams.
Where is the oil dipstick on a 1997 Honda CR-V?
On the center-front of the engine is a metal shroud with a hole in the middle of it. Look down through this hole and you should see the dipstick. (not the most user-friendly design)
What is the front track of the 2003 Honda CR-V?
The front track of the 2003 Honda CR-V is 5 ft. 0.4 in. (60.4 in.).
How do you replace Honda CR-V 1999 rear pumper cover?
The r&r of this body component is relatively stratightforward. It involves really nothing more than finding all the clips, screws, and bolts and removing them. However, the detailed step-by-step instructions are quite lengthy and (in the manuals) are accompanied by several detailed photos. MUCH too lengthy to reproduce here and the Hayne's Manual is protected by copyright laws anyway. If you are mechanically deft you could tackle this yourself by following your intuition but I suggest that you either borrow a copy of the manual from your local library or purchase one. They are a great rsource for the DIY'er.
Does a 2007 Honda CR-V have a timing chain or timing belt?
It has no timing belt, they use timing chain
What kind of transmission does the 2012 Honda CR-V have?
The 2012 Honda CR-V has a 5-speed automatic.
When to change the timing belt on a 2002 Honda CR-V?
The 2002 Honda CRV does not have a belt it has a chain which is designed to last the life of the engine.
What is the reason of a malfunction indicator lamp to show up in a special edition Honda Accord2000?
Before you can figure out why the light came on you MUST get the code that turned it on. If your vehicle is 1996 or newer you can take it to an Autozone store (if you have them in your area) and they will hook up a scan tool to your car and read the code. They say they cannot reset the light (legal stuff) but some will. If you don't have an Autozone in your area try other auto parts stores to see if they will read the code. Once you have the code you can type it into a google search to find out just what it means. It's a starting point.
