Honda Prelude

The lock must be disassembled and the tumblers inside either rearranged or replaced to fit anew key.

Beside the ECU under the passender side carpet

I had this problem in my 1998 Honda Prelude. The brake fuse light may be blown out. Under the hood in my Prelude, there is a black box. Open it and check for a brake fuse that may be blown. I think there was some wording on the box for me such as "Light" for me to distinguish the right fuse. The tiny wire inside the fuse will be split in half, so you know that it is the one that is blown. I bought some new fuses at Pep Boys and changed it. Now my brake lights work.

around 160 at 6,000

4 x 100 mm

The turning knobs under the hood of a 1991 Honda Prelude typically adjust various components, such as the idle speed or throttle cable tension. These knobs may also be used for tuning the air-fuel mixture or accessing the ignition timing. It's important to consult the vehicle's service manual for specific functions and adjustments, as improper use can affect engine performance. Always ensure the engine is off and cool before making any adjustments.

If your 1992 Honda Prelude struggles to accelerate when you press the gas, it could be due to several issues, such as a clogged fuel filter, a failing fuel pump, or a dirty fuel injector. Additionally, problems with the throttle position sensor or vacuum leaks could also cause poor throttle response. It's advisable to check the fuel delivery system and inspect for any potential air intake issues. A diagnostic scan can help identify any error codes related to the engine's performance.

To replace the speed sensor on a 1990 Honda Prelude, first, disconnect the negative battery terminal to ensure safety. Locate the speed sensor, which is typically mounted on the transmission; remove the electrical connector and the retaining bolt. Pull out the old sensor, then insert the new one, securing it with the bolt and reconnecting the electrical connector. Finally, reconnect the battery terminal and test the sensor to ensure proper function.

High mileage for a Honda Prelude typically starts around 150,000 miles, as these vehicles are known for their durability and longevity. Many Preludes can run well beyond 200,000 miles with proper maintenance. However, the condition of the specific vehicle, its service history, and how it has been driven play significant roles in determining its overall reliability at higher mileage.

To remove the center console in a 1998 Honda Prelude, start by disconnecting the negative battery terminal to ensure safety. Next, remove the screws located at the front of the console and those securing it to the dashboard. Carefully pull up the console, starting from the rear, and detach any electrical connectors for the power outlets or other components. Finally, lift the console out of the vehicle, taking care not to damage any surrounding trim.

The maximum speed of a 1991 Honda Prelude typically ranges around 130 mph (209 km/h), depending on the specific model and engine configuration. The vehicle was available with different engine options, such as the 2.0L and 2.2L inline-four engines, which contributed to its performance. Keep in mind that actual speeds may vary based on factors like condition, modifications, and driving conditions.

The manual transmission fill plug for a 1992 Honda Prelude is located on the side of the transmission case. It is typically a hexagonal plug, positioned near the top of the transmission, making it accessible for filling the fluid. To locate it, look for a plug that is slightly above the level of the transmission housing. Always ensure the vehicle is level when checking or adding fluid.

Yes, an H22 Honda motor can fit in a 1989 Honda Prelude 2.0Si, as both models share similar platform characteristics. However, some modifications may be necessary, including adjustments to the engine mounts, wiring harness, and possibly the transmission. It's important to ensure compatibility with the existing components and to check local regulations regarding engine swaps. Overall, it's a popular swap among enthusiasts, so resources and support are available.

To align the timing marks on a 1980 Honda Prelude 1.8, first, remove the timing belt cover to access the timing gears. Rotate the crankshaft using a socket and ratchet until the crankshaft's timing mark aligns with the "T" (top dead center) mark on the engine block. Ensure that the camshaft's timing mark is also aligned with its corresponding mark on the cylinder head. Once both marks are aligned, you can proceed with setting or replacing the timing belt as needed.