0
Interior Design
Planning the furniture placement and layout of the inside of a building is what Interior Design is all about. It is the branch of architecture that deals with the selection and organization of furnishings for an architectural interior.
5,109 Questions
How much does a sheet of 4x8 half inch cdx plywood weigh?
about 10to 12 pounds
If we are talking about 4' x 8' sheets, the answer is more like 45 pounds, although it can vary quite a bit by type of wood used, grade and interior versus exterior.
How many yards does a queen size bed have?
How long and how wide do you intend the finished quilt to be? Will it have a binding?
Assume that the fabric is 41" wide for purposes of calculation, and you'll have a maximum of 10% shrinkage in length. (You will need to remove the selvages before sewing the widths together, or the fabric will pucker. I'm going to assume in the calculations below that you want an 18" drop on sides and bottom, and the quilt will reach the top of the mattress, but not go over pillows. Mattress size is 72 wx84l.
72" wide + 2x18" side drops = 72+36= 108
divide by 41" fabric width = 2.63 widths of fabric, so you'll need to buy 3 x the finished length of the quilt + 10% (shrinkage)
How long does the fabric need to be? 84"+18"=102" x 3 widths = 306
+10% shrinkage = 31"
337" total, which is 9.36 yards which is 9 3/8 yards for the top of the quilt; you'll also need a similar amount for the underside, plus binding (which we can't calculate without knowing how wide you want the binding to be... assuming the top, bottom and binding are all the same fabric, about 21 yards should do, plus the batting. That also gives you a bit for matching pattern repeats.Y U NO LEARN
What colour carpet to go with taupe furniture?
i`d say a nice burgundy or a dark reddish-purple colour.
What are the advantages of a wool rug?
Wool Rugs provide the most luxurious comfort from ultra soft fibres, but there are many fibres that offer superior properties.
Man-made fibres do not shed and are much more hard wearing, offer higher degrees of stain resistance. Mand-made fibre are also colourfast and will not fade in direct sunlight. Perhaps one of the best advantages to a wool rug is that they are more eco-friendly than those of machine made, synthetic counterparts. Synthetic fibers are known to release harmful toxins known as VOC's
What do you use to clean satin nickel?
All types of nickel hardware, including satin nickel hardware, can tarnish. For this reason, it's very important to stay on top of your nickel cleaning. Cleaning all nickel hardware is done the same way. First, wash the items with a mild detergent in warm water. Rinse them completely and then dry them with a soft, lint-free cloth. If you have stubborn stains on your satin nickel cabinet hardware, you can combine baking soda with just enough water to create a paste. Then, cover the hardware with the paste and let it dry. Finally, run each cabinet hardware piece under warm water and buff dry with a soft, lint-free cloth. If you are still having problems with stains after using the baking soda, then try a silver cleaning polish. Follow the directions on the packaging to ensure that you don't scratch the metal.
Finally, if the satin nickel cabinet hardware is really heavily stained, you can try giving it a bath! Remove the hardware and place it in a bath with one part ammonia and three parts water. Make sure that the hardware is completely submerged and allow it to soak for half an hour. Then, rinse each cabinet hardware piece with warm water and dry it with a soft cloth.
What is home decor acessories?
Lamps, vases, Pictures, mirrors, statues, carpets, Almost anything that isn't strictly functional and necessary.Decorate to suit yourself. If you rent, you need landlord's permission to paint or make structural changes. Best to get it in writing.
If you are in the field of military then I am sure your room will be military home decor made. You can keep stuff like military wall plaque, magnifier, something like a spittoon or may be a horn.
Where can you buy 90 inch tall bi-fold doors?
Home depot has them in a country style but they are 3 times more expensive then a standard 30" 6 panel door hollow core.
What material do you make duvet sheets out of?
Well, duvets/comforters are usually batted(stuffed) w/ goose down to make it fluffy and comfortable. Duvet covers are made of different materials, nylon, polyester though usually cottons such as Egyptian with varying thread counts. Just as clothes are comprised of different materials; so are duvet covers.
What do you use to hang up a banner on a wall?
you are looking for an effective way to advertise a new promotion or product, mark a birthday or anniversary, or simply spread a joyous amount of holiday cheer, you will probably want to consider hanging a vinyl banner. No matter what your reasons for hanging it, it is definitely going to be something people will notice.
- How you hang the vinyl banner will ultimately depend on how long you intend to hang it. Tape can be a necessary adhesive if you are only going to use the banner for a day, such as a party for a birthday, anniversary or graduation. For best results, use either packing tape or clear duct tape, since regular duct tape will look unappealing and scotch tape will never hold. Roll a piece of tape so the sticky sides touch and put one on each of the banners’ back corners. For added security, put two in the middle of the backside of the banner. When you hang it on the wall, smooth out the tape.
- Alternatively, you can figure out the best way to hang the banner by taking its size into account. For instance, tape will work best for smaller banners but you may wish to fasten a banner larger in size using nails.
- If your banner has loops on each of the corners, hammer nails into the holes. Do not hammer the nails in so the head is adjacent to the wall, but rather, leave some sticking out so the banner has a little legroom with which to hang.
- You can use a vinyl banner to decorate a table. Center the banner in a way that allows it to slide over to the table front with a small bit of the banner still on the table top. Use clear duct tape to fasten the banner to the top of the table, leaving you with a fashionably well placed table banner.
- Lastly, you can use clear duct tape to hang a vinyl banner either on a door or on a window so it can be displayed to the outside world. Make sure you use a strong enough tape, and enough of this tape, so that it will not be torn down by any wind, weather or any other kind of outdoor element. Also make sure the banner is not in direct danger of being snowed or rained on.
How much fabric is required to upholster a wing back recliner?
My quasi-educated guess would be around 7 yards. Depending on the size and style of the chair, it could be as low as 6 yards or as high as 8 yards.
If the fabric has a repeating pattern or the chair has a skirt you may need as much as 11 yards. Take digital pictures of the chair from the front, back and side and measure it height, width and depth. Take the pictures with you when you are looking for upholstery fabric and ask for assistance with the yardage.
How do you remove fuzzballs from upholstered couch?
Wide clear trasparent tape can be used,in a put the tape on the couch,pull the tape off fashion.Also you can shave the couch lightly with a disposable razor.I have also seen a few years ago a battery operated tool called ,something like Fuzz buster,I saw it in a fabric store.
Will a king size down duvet fit in a queen size duvet cover?
It probably will do, just try it. You never know unless you try.
Answer two.
The King duvet is about 15 Inches longer and about four inches wider than the Queen, so you might have to fold over at the top, but I am sure it will work for you. You could also remove the excess inches.
What carpet colour goes with cream and red walls?
Dirt red or cream. Or combine those two. It also depends what tone that brown is. When it's lighter, a bit darker wall would be good, when it's dark brown, light walls would be better. A little contrast makes it easy on the eye (a very bright room or very big contrast makes eyes hurt, a very dark room makes you feel depressed over the time).
Can you put linoleum tiles over ceramic tile?
Hardwood, yes.
Laminate , yes.
Tile, I wouldn't. you can put tile over it if you put backer board over it, or if you have 3/4 inch subfloor underneath and the vinyl is glued well you can use a superflex motor from lowes. but the backerboard is the best choice
How do you install Ceiling Tiles?
Tile is one of the oldest types of finish covering used on pitched roofs. Tile roofing has grown increasingly popular because of its fireproofing qualities. Clay or concrete tile roofing is available in a variety of styles. Clay tile is manufactured by baking plates of molded clay into tile, and is lighter than concrete tile. However, concrete tile is more durable and is used more often than clay tile.
- Roof
- Saw
- Battens
- Cant strips
- Tiles
- Underlayment
- Metal flashing
- Step 1 : Install underlayment across the sheathing of the roof. There is a wide selection of asphalt-saturated felt underlayment available, but 30 pound felt is the most commonly used type. Research local building codes to determine what type of underlayment to use. Follow underlayment manufacturer instructions when installing
- Step 2 : Install the metal flashing where needed. Places such as valleys, chimneys, skylights, and where a roof butts against a vertical wall will require metal flashing. The flashing should be a 28-ga corrosion-resistant metal.
- Step 3 : Nail the two-inch thick cant strip flush with the eave of the roof. This strip, which is twice the thickness of the battens, slants the first course of tiles so that it matches the rest of the courses. Every four feet, allow a half-inch to one-inch gap to let water drain across the row of cant strip and the battens, which will be placed across the entire roof.
- Step 4 : Hook a tape measure to the roof eave and measure up the length of the tile being used; make a mark on the underlayment. The tiles will have a one-inch overhang at the eave and the half-inch head lug at the rear of the tile, so minus one-and-a-half inches from the first mark and make a mark on the underlayment. Do this at both ends of the roof and then snap a line with a chalk box. For example, if the tile is 16 inches, the mark will be made 15 inches up from the eave.
- Step 5 : Nail the 1x2 batten below and flush with the snapped line. For the rest of the snapped lines for the battens, minus three-and-a-half inches from the length of the tile being used and snap lines this length across the rest of the roof. For example, if the tile is 16 inches, the marks will be placed every 13 inches up the roof and snapped out for the battens.
- Step 6 : Lie the tile down by working in a left to right direction because of the vertical keyway between the tiles. Vertical interlocking joints must be free of any foreign matter to ensure a proper fit and interlocking of the tiles. The head lug, which is the lip at the rear of the tile, will rest behind each row of battens. The number of tiles to be fastened with nails depends on the roof slope, on whether or not battens were used, and on the anticipated wind velocity in the area. Research local building codes to determine the tile nailing schedule.
How do you turn satin paint into flat paint?
I prefer to paint all walls and ceilings satin. I have no idea why people just automatically think that ceilings have to be flat...or even white. I do satin on the ceilings because of dust, yes dust does stick to the ceilings, esp near AC vents and around ceiling fans. Have you ever tried to sweep your flat white ceiling to get the dust off after a few years? It just smears. I think satin ceilings make small rooms brighter and larger. You must use satin or semi on the ceiling in the bathrooms, a bathroom environment is the one interior space that is actually most like an outdoor space with water splashing, steam, humidity, extreme temp changes, I wonder if it would be best to use exterior paint in the bathroom. For ceilings though I pick a white with a bit of grey and go all satin.
How do you sand and prime furniture made of wood?
If the furniture is painted then you would need approx a 60-80 grit sandpaper, then gradually move to a finer paper. When paint is almost gone finish with about a 320 or 400 grit paper so it is completely smooth. If you want to repaint then you don't need to remove all the paint unless you are painting over an enamel paint with a latex. (oil based vs. water based). You can however prime it with a good primer once the wood is smoothed. Or if you remove all paint you can then stain it. before you paint/stain your wood be sure and remove all dust from the wood with a clean damp cloth. let wood dry and then proceed. good luck and wear a dust mask :-)
How many yards fabric do you need for size 14 dress?
Go to the link I have provided.
Click on the type of pants you want, and scroll down to the yardages shown. There is a column heading at the top for size, follow that column to the width of the material (45" or 60") and you will see what the basic fabric amount is.
What type of wood would you use to build a false floor or platform to put furniture on?
In order to have a false floor the first step is to create the space necessary for the false floor. Remove the existing foundation and escalate the desired depth or crawl space desired. Create a load bearing foundation to rebuild a foundation to replace the original flooring after that.
What is the minimum enrty door width?
There are two was to answer this question. There is the Practical way and the Prescribed way.
The practical way is to verify the largest item or number of people that you want or need to get through the door. You also should know how easily or quickly you need that to happen. Then, you design around those requirements.
Then there is the prescribed way. The International Building Code requires that you have a minimum of 32" "clear width" at all exit doors. There is no minimum at all other doors. There are other exceptions and also additional widths based on occupancy (use of space) and occupant load (number of occupants).
Please be sure to contact your local Building Department for verification and additional information as these requirements are subject to local addoption and interpurattion.
I hope this has helped!
Terry, CBO
Building code requires a 36" door for means of egress not 32" for residential construction. Handicap doors are required to have a 32" clear opening.
What is the standard width of a closet door?
My name is Kylie and I live underground. I hate my mother and my father and my little sister Devon. I have only one friend called Anastaciana. She is a rag doll. I have no nose and no teeth. My mother ripped them out with pliers and my dad beat my nose over and over again until it fell off. I have horrid white eyes and it looks like I'm a cartoon. I taught myself how to read and write because my mother never sent me to school. I never done anything bad. Only once and my punishment was having my teeth ripped out and my nose beaten. The thing I did that was bad was throwing my sister's teddy across the room. I was banned from her room and my room has been locked ever since. I am literally as thin as a stick and I have no nails. I only have 30 milliliters of water per day and I have one long-lasting 24 hour meal gum per day. My mum puts the food and drink through a hatch at the top of the door. My bed is two coats stitched together as a mattress, a book with a cotton cloth sewed around it as a pillow and 2 pashminas as a blanket. Please help me. I have made a tunnel. The only thing I don't know is where I am. I can't study any more. It gave me square eyes. So I didn't study places and such. I scream every night. This is true. There was a drawing attached to it which looked like a photo. But it wasn't I proper freaked out when I read this. If you don't c + p (copy and paste) this to 10 different places within the next 5 hours, she will come to your bed at 9pm tonight, kill you with a knife and eat you.
How do you join two pieces of wood with screws?
Drill a hole in the first board the diameter of the screw and screw into the second board. This will pull the two boards together. If you screw through both boards without the hole the first one will lift slightly when the screw goes through so the boards will not be held tight together.
What kind of nut do you use to hang frames?
Personally, I don't think there is a need to use nuts, drills, nails to hang anything on the wall. This is because there are many products available in the market that provide a drill-free option to the users. For example, most people find Command Strips to be one of the best options while doing so. However, Command strips are useful, however, they don’t provide the reusability to the consumers. Moreover, some of their products can’t be used for multiple purposes. For example, a command hook won’t allow one to hang a photo frame due to its mechanism. As an alternative: I found this new innovative product called KLAPiT. It works as a double-sided tape, just like 3M, but gives us the reusability and versatility through its innovative design. Specifically, it uses 2 steel tapes, with a super-strong magnet that allows users to hang frames, clocks, shelves, paintings, and anything with a flat surface on to the wall. This product has a very interesting mechanism and you can check it out here: The Best Double Sided Tape for hanging - KLAPiT. I personally find this product very useful and would recommend it to everyone.
