Kia Optima

The curb weight of the 2014 Kia Optima is 3237 lbs..

The CVA Optima and the Optima pro are the same guns except for the barrel length (26" & 29"). Barrels are interchangable.The optima elite is a newer different gun and I Don't have experience with it.

Rates vary. Get a quote from a mechanic.

1. Disconnect negative battery cable.

2. Disconnect electrical connector from headlight assembly.

3. Remove back cover by pushing in on cover, then rotating cover counterclockwise to disengage from

headlight assembly.

CAUTION: The headlight bulb is filled with a gas which is under pressure.

Damage to glass part of bulb can cause bulb to explode causing

possible personal injury.

4. Pull socket with bulb straight back and remove it from headlight and combination light assembly.

5. If bulb has failed, place it in new bulb carton and dispose of properly.

6. Hold replacement bulb by base, or use clean cloth or paper to avoid touching glass, and install bulb in

socket.

7. Align slots on bulb with corresponding bosses on headlight assembly. Insert bulb into headlight and

combination light assembly.

8. Install back cover to hold bulb in place.

9. Connect electrical connector.

10. Connect negative battery cable.

1. Sit in the vehicle and close all the doors. Insert the key into the ignition.

2. Turn the key to the "Off" position then to the "On" position. Repeat this until the door locks cycle to indicate that the programming mode is activated. End with the ignition key in the "On" position.

3. Press the "Unlock" or "Lock" button on the programmable remote. Listen for the doors to lock or unlock to verify successful programming.

4. Turn the ignition key to the "Off" position. Listen for the door locks to cycle to indicate that you have exited the programming mode.

5. Repeat the above steps to add any additional remotes.

The gas tank on the 2001 Kia Optima holds 17.2 gal..

The 2014 Kia Optima runs on regular unleaded.

The 2005 Kia Optima has 39.0 in. of front head room.

You will need to remove the front tires. Remove the brake assembly spring. The brake shoes will come off. Reverse the process to install the new brakes.

The drivetrain warranty of the 2014 Kia Optima is 10 yr./ 100000 mi..

Underneath the sparkplug wires. If you have the 4-cylinder, there should be 4 wires/plugs in the holes in the valve cover (or three on each side in the V6). If you pull up on those wireplugs, the sparkplugs are inside those cylinders.

The 2005 Kia Optima's engine produces 138 hp @ 5500 rpm.

I need to know how much will a throttle sensor cost to fix a kia optima

buy new ones and put those in instead

The ground clearance of the 2013 Kia Optima is 0 ft. 5.3 in. (5.3 in.).

The 2012 Kia Optima has a 6-speed manual.

It stands for "Tire Pressure Monitor System"

Replace there are no adjustments.

Quote: I have a 2003 Kia Sorento and when my husband changed my headlights I asked him to "adjust" them. He tried to put he said that they can't be adjusted to point higher, lower or whichever way because they are screwed into place. Unquote.

Just in case anyone comes across this reply when looking for how to adjust Sorento headlights: the answer above is wrong. Sorento headlights are adjustable up & down, and side to side with a Phillips screwdriver. In addition, some Sorentos have and in-vehicle headlight adjustment switch so you can adjust for extra weight in the rear while you are driving.

you have a timing belt its be-hin the cover

This question cannot be answered. IT DOESN'T MAKE SENSE!!!!!!

The 2002 Kia water pump is located on the front of the engine. You can follow the bottom radiator hose directly to the water pump.

Both codes indicate a problem within the Transmission Control Module or TCM. Take it to a transmission shop, they can pull any additional code from the TCM.

The fuse box should be just inside the door on the lower left hand side of the steering wheel. Your left shin should touch it when driving. You'll need a key to pop the cover off. There is another fuse box inside the engine over the left front tire in a black box.

Open the hood and on the left side (passenger) you will see a round black cap towards the front of the car along the sidewall. It is to the right of the windshield washer's fluid reservoir. Remove the cap and fill to between the minimum and maximum line stamped on the outside of the reservoir. Make sure you fill to between these two lines. There is also a dipstick built into the cap. Make sure you have the fluid in the crosshatched section of the dipstick. Replace the round black cap. If you are having to fill up the power steering reservoir often (more than once every year or two) you probably have a leak. Look for fluid on the engine's serpentine belt as the Power steering pressure line is routed directly above the serpentine belt on its way to the rack and pinion steering unit at the rear of the engine bay. This results in the serpentine belt having p/s oil on it and the p/s pulley will often slip, making it feel as if your power steering pump is bad. These pressure lines often leak at the first crimping connection directly above the power steering pump's pulley wheel. The entire line has to be replaced (consumer's price at the dealer is approximately $140). Most backyard mechanics can replace this line (2 connections - one at each end & 2 clamps) without much problem, although it is a bit tricky to snake it back along the firewall. Two people make it an easy install. This will save about another $130 or so to have the dealer install it. Make sure you use a flare nut wrench at the steering rack end, as the nuts used in most fluid line connections are softer than the boss that they are screwed into to ensure a leak-free connection. Use a funnel to fill the [power steering reservoir to the correct level, then turn the engine on and continue to slowly fill to the correct level. Have a second person turn the steering wheel to full left then full right about 8 - 10 times to "bleed" the air out of the system. Check for leaks at both ends of the power steering pressure line. Using a pressure car wash hose to rinse all of the p/s fluid from the serpentine belt and engine will stop it from slipping, as the fluid had tended to splay all over the side of the engine and engine bay.