Toyota Cressida

The engine number for a 1991 Toyota Cressida is typically located on the engine block, often on the driver's side, near the front of the engine. It can usually be found stamped into the metal surface, often near the cylinder head or on a flat area of the block. To easily locate it, you may need to clean the area of any dirt or debris. Always refer to the vehicle's service manual for specific details related to your model.

The 1989 Toyota Cressida is equipped with one oxygen sensor located in the exhaust system. This sensor helps monitor the oxygen levels in the exhaust gases to optimize fuel efficiency and emissions. It's important to note that some modifications or different engine configurations might alter this setup, but the standard configuration includes just one oxygen sensor.

To change the timing belt on a 1986 Toyota Corolla, start by disconnecting the battery and removing the engine cover. Next, align the timing marks on the crankshaft and camshaft gears to ensure proper timing. Remove the old timing belt by loosening the tensioner and sliding off the belt. Install the new timing belt, ensuring it's aligned with the timing marks, then reassemble everything and reconnect the battery. Always consult a repair manual for specific torque specifications and detailed steps.

If the tail lights on your 1989 Toyota Cressida are not working, first check the bulbs for any signs of burning out or damage, as they may need replacement. Next, inspect the fuse box for any blown fuses related to the tail lights. Additionally, examine the wiring and connections for corrosion or loose connections that could disrupt the electrical flow. If all else fails, consulting a professional mechanic may be necessary to diagnose any deeper electrical issues.

To remove the alternator from a 1986 Toyota Cressida, first, disconnect the negative battery terminal to prevent electrical shock. Then, remove the drive belt by loosening the tensioner and sliding the belt off the alternator pulley. Next, disconnect the electrical connections from the alternator and remove the mounting bolts securing it in place. Finally, pull the alternator out of the engine bay.

To reset the alarm on a Toyota Cressida, insert the key into the ignition and turn it to the "On" position without starting the engine. Then, press the alarm reset button, usually located on the dashboard or near the steering column, or unlock the driver's door with the key. If the alarm is still active, disconnect the battery for a few minutes to reset the system before reconnecting it. After resetting, try starting the car again.

To repair a clutch that intermittently does not release on a 1996 Corolla, first inspect the hydraulic system for leaks or air in the lines, as this can affect clutch operation. Check the clutch master and slave cylinders for proper function; replacing them may be necessary. Additionally, examine the clutch cable for proper tension and any signs of wear or damage. If these components are functioning correctly, the issue may lie within the clutch assembly itself, requiring replacement of the clutch disc, pressure plate, or release bearing.

To change the headlight bulb in a 1991 Toyota Cressida, first, open the hood and locate the back of the headlight assembly. Disconnect the electrical connector by gently pulling it off the bulb. Remove the rubber dust cover if applicable, then twist the bulb counterclockwise to release it from the socket. Insert the new bulb, ensuring not to touch the glass with your fingers, and reverse the steps to reassemble everything.

To replace the headliner on a 2000 Toyota Corolla, start by removing the interior trim pieces, including the A and C pillars, and any grab handles or lights attached to the headliner. Carefully detach the old headliner from the roof, ensuring you don’t damage any wiring or clips. Cut a new headliner material to size and apply adhesive to both the roof and the new material. Finally, reattach the headliner, trim, and any other components in reverse order.

To calculate the paint quantity needed for a car, first measure the surface area of the car by estimating or using the dimensions of the body panels. A typical car requires about 1 to 2 quarts of paint for a complete repaint, depending on its size and the number of coats desired. It's essential to consider the paint's coverage rate, usually indicated on the can, which tells you how many square feet a gallon will cover. Always round up to account for any overspray or mistakes.

The 1997 Toyota Corolla features several warning lights on its dashboard, including the check engine light, oil pressure warning light, battery charge warning light, brake warning light, and seatbelt reminder light. Each light serves as an indicator for specific issues, such as engine problems, low oil pressure, or electrical system failures. For detailed information, refer to the owner's manual, which explains the significance of each light and recommended actions. Always address any warning lights promptly to ensure safe vehicle operation.

On a Toyota Cressida, the starter is typically located on the lower side of the engine, near the transmission. It is mounted to the engine block and can be accessed from underneath the vehicle. To reach it, you may need to remove any components obstructing access, such as the exhaust or heat shield, depending on the specific model year. Always ensure that the battery is disconnected before attempting any work on the starter.

To replace the lower ball joints on a 1979 Toyota Cressida, first lift the vehicle and secure it on jack stands. Remove the wheel, then detach the brake caliper and rotor to access the lower control arm. Unbolt the ball joint from the control arm and the steering knuckle, using a ball joint separator if necessary. Install the new ball joint by reversing the removal process, ensuring everything is torqued to specifications before reassembling the brake components and wheel.

A twin cam motor, such as the 4AGE, can potentially fit in a 1993 Toyota Corolla with the right modifications. However, it may require adjustments to the engine mounts, wiring harness, and possibly the transmission. It's important to consider compatibility with the existing drivetrain and emissions regulations. Custom fabrication may be necessary for a successful installation.

The cooling box fridge in the glove box of the Toyota Cressida became available starting with the 1989 model year. This feature was part of the Cressida's luxury offerings, enhancing the vehicle's appeal for comfort and convenience. The integration of this cooling box was indicative of the era's focus on adding amenities to mid-size sedans.

In a 1990 Toyota Cressida, the lock-up solenoid is typically located inside the transmission assembly, specifically within the valve body. It is part of the automatic transmission system and is responsible for controlling the engagement of the torque converter lock-up feature. Accessing it usually requires removing the transmission pan and valve body for inspection or replacement. Always refer to a repair manual for detailed instructions specific to your vehicle.

remove the screws which are hard to get to.

BEING A COMPLETE NOVICE, I FOUND MINE RIGHT WHERE YOU HEAR THE CLICKING NOISE UPON ATTEMPT TO START MY CAR. IT IS A LITTLE PLUG, ABOUT 1 NCH BY 1 INCH HOPE THIS HELPS

It's located below the fuel inj. rack. Difficult to see from above. You'll need to get under the car to see it better. You can allow follow the + cable from your battery and it will lead you to it. Remove the bottom shields and the air filter box for easier removal.