answersLogoWhite

0


Best Answer
It was in the under the dash, mostly on the drivers side of center. Remove the driver's side facia in the footwell. You will need a 7mm nutdriver/wrench/socket or a small adjustable.


Once the facia is removed, you'll see the turnsignal relay. If one of your turn signals is still working, you can turn it on and feel the vibration. Our unit has a metal cap over the relay. The replacement was clear plastic.


Remove the wiring harness, put on the new one, reassemble.

User Avatar

Wiki User

10y ago
This answer is:
User Avatar
More answers
User Avatar

Wiki User

12y ago

Ok I just replaced mine so here are the exacts. It sets under the dash left of the steering column under the dash. So take the 3 screws "10mm socket"off the plastic piece under the steering column. Then remove the plastic center mold off the heater control panel. Behind that the right 10mm screw top for the short column piece you should have seen the other on the left by removing the fuse cover left of column. Now you have the column piece off take a light and look upside to view the column under the dash. You will see a silver metal round fuse clipped to a spring load. Just pull out tward the driver door and it will pop out of the spring holder. There you go took me a half hour to find it 1 minute to change it.

there is a clip on the bottom of the fuse box and you can push the fuse box in and the flasher is right behind it

This answer is:
User Avatar

User Avatar

Wiki User

13y ago

Fig. 12 Lock Plate Retining Ring Removal

Fig. 13 Taping Turn Signal Electrical Connector & Wiring

Fig. 14 Lifting Turn Signal Switch From Column Bowl

Fig. 15 Turn Signal Switch Replace

  1. On models equipped with airbags, disable airbag system as described under MAINTENANCE PROCEDURES/AIRBAG SYSTEM DISARMING .
  2. On all models, disconnect battery cable, then remove steering wheel and column to instrument panel trim cover.
  3. On models with telescoping column, remove bumper spacer and snap ring retainer. On all other models, remove cover from lock plate.
  4. On all models, using a suitable tool, compress lock plate (horn contact carrier on tilt models) and remove snap ring (C-ring on tilt models), Fig. 12.
  5. Remove lock plate, cancelling cam, upper bearing preload spring, thrust washer and signal lever.
  6. Remove turn signal lever or actuating arm screw, if equipped, or on models with column mounted wiper switch, pull lever straight out of detent. Depress hazard warning button, then unscrew button.
  7. Pull connector from bracket and wrap upper part of connector with tape to prevent snagging the wires during removal, Fig. 13. On Tilt models, position shifter housing in Low position. Remove harness cover.
  8. Remove retaining screws and remove switch, Figs. 14 and 15.
  9. Reverse procedure to install.
  10. Rearm airbag system as described under MAINTENANCE PROCEDURES/AIRBAG SYSTEM DISARMING .
This answer is:
User Avatar

User Avatar

Wiki User

8y ago

Visit http://www.likeabigdog.com/column/94upsignal.htm

This answer is:
User Avatar

User Avatar

Wiki User

16y ago

There is a very good step-by-step at this site: http://tss.likeabigdog.com/

This answer is:
User Avatar

User Avatar

Wiki User

9y ago

It is quite simple to replace the turn signal switch on your 1990 Buick LeSabre. The turn signal switch simply plugs in and out.

This answer is:
User Avatar

User Avatar

Wiki User

9y ago

history of colour

This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How do you replace the turn signal switch located on a 1995 Buick LeSabre?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

How do you repair the switch for the bright lights for a 1992 Buick LeSabre?

replace the combination switch on the turn signal stalk


Why would the turn signal not work if it is not the fuse located on a 1991 Buick LeSabre?

Bulbs or turn signal flasher, maybe even the switch.


Where is the turn signal switch located on a 2001 vw passat?

turn signal switch is the hazard button! Pull out hazard button and replace it! good luck!


Where is the turn signal flasher located on an Audi 2003 s3?

It's in the hazard warning switch. You need to replace the switch.


How do you replace the turn signal switch on a 2003 Chevy Silverado.?

The 2003 Chevrolet Silverado turn signal switch is located below the dashboard, on the drivers side of the passenger compartment. The turn signal switch simply plugs in and out.


How do you replace the turn signal switch located on a 1998 Chevy Lumina?

pull the steering wheel


How do you replace the turn signal switch on a 2001 Yukon?

You need to remove the steering wheel. The switch is located below the steering wheel.


What does it mean when your signal light does not blink?

The flasher is broken. It is located inside the hazard switch and easy to replace. The switch is about $30 from the dealership and takes 10 minutes to replace.


How do you replace the turn signal switch located on a 2001 VW Golf GLS?

Change the flasher first.


Turn signal switch replace 96 Plymouth voyager minivan?

The turn signal switch is quite easy to remove and replace. The turn signal switch simply plugs in and plugs out.


Where is the headlight dimmer switch located on a 2004 Chevy Blazer S-10 and how do you replace it?

dimmer switch is on the turn signal lever, to replace you need to remove steering wheel


How do you replace the turn signal switch located on a 1993 Pontiac Grand Prix?

My turn signal switch died on my 92 Grand Prix. Rather than attempting the repair, I took it to a shop. The steering column had to be removed to get to the switch.