0
Buick Rendezvous
This category covers questions about the Buick Rendezvous, a mid-sized crossover SUV that was manufactured by General Motors and sold through its Buick division. The Rendezvous was produced from 2001-2007 and was succeeded by the Buick Enclave.
1,007 Questions
Where is the fuse for the front power outlet on 2003 buick rendezvous?
Per the manual for my 2002 Rendezvous, the passenger side of the center console down by the floor has a cover for a fuse panel. The REAR Aux power outlet fuse is #14. Under the hood near the battery is the other fuse panel. You have to remove the black cover to get to it. The cover is marked with "Fuse Relay center." # 32 is labeled in the manual as Front Power Outlets(plural), "lights" and ""Onstar. Since they mention more than one, it must mean that the front and the one at the rear of the center console are off the same fuse. # 45 is the main battery fuse for the power outlets but is also for the body computer, level control, power seats and mirrors. If only the fronts are out, it is probably #32 in the panel under the hood. What "lights", I am not sure.
How do you drain a radiator on a2002 buick rendevous?
If there is no drain petcock then just remove the lower radiator hose.
"http://wiki.answers.com/Q/Service_Traction_System_light_comes_on_when_you_turn_the_wheel_to_the_right_is_there_a_wire_that_may_be_pinched_on_your_2002_buick_rendevous"
What did they do for a rendezvous?
They often worshiped their gods by dancing around a fire and playing various instruments. They also would eat lots of food and play games, such as throwing axes ect...
Where are the main fuses for the AC located on a 2000 Ford 350 Van V10?
# 13 15 amp fuse in Central Junction Box
How long are the wipers on 2003 Rendezvous?
Drivers side 24 inches, Passenger 22 inches. https://www.mygmlink.com/pdf/go2content/manual/US/en/buick/2003rendezvous.pdf
How do you program the remote key fob on a 2005 Buick Rendezvous?
There's a manual method of programming keyless entry transmitters also. Make sure that you have all the transmitters you want to be able to use handy because the system will have to "learn" each one, even if they already worked before. If you have the memory seat/radio/mirror option you'll need to program the remote for 'There's a manual method of programming keyless entry transmitters also. Make sure that you have all the transmitters you want to be able to use handy because the system will have to "learn" each one, even if they already worked before. If you have the memory seat/radio/mirror option you'll need to program the remote for 'driver 1' first, then 'driver 2', then up to 2 others. Here's how to do it:
1. Close the vehicle doors.
2. Turn OFF the ignition.
3. Remove the ignition key from the ignition lock cylinder.
4. Press and hold the driver side door lock switch to the unlock position.
5. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.)
6. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.)
7. Insert the ignition key into the ignition lock cylinder. (Do not turn the ignition key in the lock cylinder.) Leave the ignition key in the ignition lock cylinder.
8. Release the door lock switch. The body control module (BCM) will sound three beeps in order to verify the Program Mode has been activated.
9. Press the lock and unlock buttons on the keyless entry transmitter simultaneously for approximately 5 seconds . The BCM will sound two beeps in order to verify that the transmitter has been successfully programmed.
10. Perform the previous step to program up to four transmitters.
11. Remove the ignition key in order to exit the Program Mode.
12. Verify the proper operation of each transmitter.driver 1' first, then 'driver 2', then up to 2 others. Here's how to do it:
1. Close the vehicle doors.
2. Turn OFF the ignition.
3. Remove the ignition key from the ignition lock cylinder.
4. Press and hold the driver side door lock switch to the unlock position.
5. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.)
6. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.)
7. Insert the ignition key into the ignition lock cylinder. (Do not turn the ignition key in the lock cylinder.) Leave the ignition key in the ignition lock cylinder.
8. Release the door lock switch. The body control module (BCM) will sound three beeps in order to verify the Program Mode has been activated.
9. Press the lock and unlock buttons on the keyless entry transmitter simultaneously for approximately 5 seconds . The BCM will sound two beeps in order to verify that the transmitter has been successfully programmed.
10. Perform the previous step to program up to four transmitters.
11. Remove the ignition key in order to exit the Program Mode.
12. Verify the proper operation of each transmitter.
How do you replace a thermostate on a 1998 Bonneville?
First, drain off the radiator fluid to a level below the upper radiator hose. Then disconnect the hose from the water neck on the engine block (and from the radiator if you wish). Remove the water neck, and the thermostat is right there to replace (under the water neck on the engine intake). After replacing the thermostat and bolting down the water neck, reconnect the upper radiator hose, etc, warm the car up. add radiator fluid, then be sure to loosen the screw on the water neck that allows any trapped air in the water neck to escape. You should see a stream of radiator fluid exiting the vent on the water neck. Retighten the vent screw, and fill the radiator to the top and replace the pressure cap, and you should be good for a long time.
What causes drivers window to go down but not up on a 2002 Buick Rendezvous?
It can be a broken wire in the hinge area, a bad switch, or simply a bad window regulator.
See this post for instructions on how to diagnose the problem:
Why wont your 2003 Buick rendezvous start even though there is plenty of power from the battery?
This has to do with faulty computer systems. Call Buick 1-800-790-5600. If all problems are reported directly to Buick they will have to do recalls. The Body Control Module computer will take out other computers. I got Buick to pay for half of the expenses because I called and complained about the lack of safety when a vehicle will not start due to a design flaw.
Take it to the dealer crushed metal gasket or something Replaced w rubber and a boot and rocks up in the awd driveshaft. Cost me $300
From wikipedia
Antifreeze is used in internal combustion engines, and for many other heat transfer applications, such as electronics cooling and chillers for HVAC. Compounds are added to water to reduce the freezing point of the mixture to below the lowest temperature that the system is likely to be exposed to, and to inhibit corrosion in cooling systems which often contain a range of electrochemically incompatible metals (aluminum, cast iron, copper, lead solder, etc.). The term 'colligative agent' is to be preferred as, in warm climates, the benefit of these compounds is to increase the boiling point of the coolant, which should then be more properly referred to as 'anti-boil', and as anti-freeze decreases and increases both properties, respectively, 'colligative agent' more accurately describes the liquid. The term 'engine coolant' is widely used in industry.
Where is the outside temp sensor located on an 2002 buick rendezvous?
2002 buick rendezvous ambiant temperature sensor location
How do you change coolant in rendezvous?
step1: remove coolant cap
step2: put coolant in
step3:put cap back on
Defective or disconnected sending unit. The density of the coolant is measured as well as the quantity, it does not have enough antifreeze to 'float' the sensor....
What does service traction control mean?
How to reset the service traction control light on a 2007 Chevy Sub?
How many miles per gallon does an 2005 buick rendezvous get?
I have a 2005 Rendezvous with the optional Versatrak AWD and I get around 20-22 mpg mix driving.
Can you repair a hole in the windshield fluid reservoir with epoxy?
Yes, use an underwater glue. It stays flexible and will last. Clean the reservoir with acetone, roughen it, clean again and apply a patch. For the patch use PVC film or even aluminum foil.
Yes. Use J B Weld. It will last for a while, but vibration will crack it again. Buy a new bottle.
