0
Chrysler LHS
The LHS is a four-door full-size sedan produced by Chrysler from 1994 to 2001. The car features a 3.5-liter V6 engine, and a 4-speed automatic transmission. It was based on the Chrysler LH platform.
543 Questions
How do you reset your 1997 Chrysler lhs alarm?
Unlock the car with the remote or the key in the door.
Unlock the car with the remote or the key in the door.
How do you restart Chrysler lhs when the alarm goes off?
you have to dis-engage the passangers door lock with car off.
How do you reset the alarm on a 1996 Chrysler LHS?
You can not disable, it is part of the body computer. Unlocking the drivers door with the key should turn it off if it is activated.
Where is the fuel shut off valve reset switch on a Chrysler LHS?
Chrysler does not use reset switches.
What year did the Chrysler 300 come out?
In 1955 Chrysler introduced the 300. The car was redesigned in 2005 by Ralph Gilles and Freeman Thomas. The car has many different versions to make the car more appealing to many.
Where is a neutral safety switch on a 1994 Chrysler lhs?
It is inside the transmission, on the valve body.
Where is the fuel filter located and how do you replace it on a 2000 Chrysler LHS?
The fuel filter is located in the gas tank as part of the fuel pump assembly. So change it whenever you have to replace the fuel pump.
Where is the tcc solenoid located on a 2002 chrysler 300m?
All solenoids are part of the solenoid pack on the valve body inside the transmission.
Need to remove a part of CV joint that wont come out?
had the problem -- if grease isn't put on it when first assembled, or its been a long time - the trans shaft will start to rust and the c- clip on the shaft will not be able to compress. Only way toi get it off is to cut it -- use a dremel - cut the shat with the dremel at a 90' angle to the cvshaft - make 1 cut alon it -- be careful not to go in too far - then turn the cvshaft 1/4 turn and do another cut - then just before the shaft gets large -- cut across the the 2 new cuts and get a cold chisle drive it between 1 of the fits cuts and the CV shaft should break apart where the cut is -- that takes care of 1/4 - then make new cut - turn shaft 1/2 way around - and with 1/2 the shaft cut away -- it should just pull off-- with a dremel -- it took me about an hour from start to finish-- not bad
Where is the starter on a 1999 Chrysler lhs?
Under the driverside exhuast manifold, good luck its a tight spot
What is the book value of a 1996 lhs chrysler?
Depends on many factors including mileage on the vehicle, condition, options, and if it needs any repairs. Click the link and look up the value for yourself.
Where is the thermostat located on a 2000 Chrysler LHS?
the thermostat on a lhs 3.5 is under the alternator in the bottom radiator hose fitting. it is pretty easy from the top. remove upper rad sup./remove alt./ disc. bot. rad hose/ect.. always drain goolant / pet cock pass-side of rad.
Does coolant run through the condenser?
No. Coolant only runs through your radiator into the engine and back again. Your condencer is part of your A/C system.
If you do not have any external leaks, a head gasket is most likely.
Left Hand Side
Luxury Highline Sedan
Actually LHS stands for: LexingtonHighSchool
Where is the fuel pump on a 1994 chrysler lhs?
It is inside the fuel tank. There is an access panel under the carpet in the trunk.
Where is the transmission control module tcm located on a 1998 chrysler lhs?
Near the windshield fluid washer resovior, under the speed control servo.
How hard is it to change a timing belt in a 99 LHS?
If you are good with cars and have tore into the long block of an engine it can be done. Begin by disconnecting the battery. You will need a healthy set of tools including a torque wrench and a puller for the crankshaft pulley. It has been a little while since I did this repair, so I may miss a few steps. I would strongly recommend purchase of a Chilton's or Hayes repair manual for this car when doing this. First, the radiator has to be removed and radiator housing needs to be loosened. Drain the radiator first. The idler pulley for the serpentine belt has to come off and then the serpentine belt itself. Loosen the alternator and swing it out of the way. Do the same for the power steering pump. Loosen the Air Conditioning compressor (do not disconnect it as this will result in coolant loss and a mess, possible violations of the clean air act) and remove the belt, then swing it out of the way. Find something to secure the crankshaft pulley from rotating and remove the bolt holding it on. Fit the puller over the pulley and remove it. (Note, it may be possible to remove the crankshaft bolt before any of the accessories or belts and use tension on the belts to prevent the engine from rotating) With the crankshaft pulley removed, remove all of the covers on the front of the engine to expose the timing belt. MARK THE POSITION OF THE TWO CAM SPROCKETS AT THIS POINT TO ALLOW YOU TO ALIGN THEM PROPERLY LATER. Release the tensioner and remove the timing belt. Also, at this time, the water pump will be fully exposed and it is a GREAT idea to replace this at this time also to prevent going through all of this again should the old pump fail. Essentially reverse the process to finish the repair. I used high heat permatex on all surfaces to keep as much dirt out as possible during the re-assembly and subsequent operation of the car. Be sure to torque the bolt securing the pulley to the crankshaft to the proper specification, which I cannot remember right now and I do not have my car manual handy. This can easily be found in Hayes or Chiltons, or through a search engine. If I have omitted anything feel free to update this as this was totally through memory having done this repair a few months ago.
Why after changing the flasher on a 1997 Chrysler LHS the turn signals come on but do not blink?
Are you sure you replaced the Turn Signal Flasher Relay? Some vehicles has a relay for the turn signals and one for the hazard lights. Possibly you changed the wrong one. It is also possible you purchased a new defective part. It happens although rarely.
Why would there be no sound from the car stereo of a 1997 Chrysler LHS?
I had the same problem with my 1997 LHS until about 10 minutes ago. If you go into your fuse box (To the left of the steering wheel, behind the removeable panel that is exposed when the door is open) the fuse for the radio/horn is #8. Check to see if the metal piece inside the fuse is broken, if it is broken, replace it with a 20 amp fuse. I hope I helped and good luck!
Where is the cruise control fuse located on a Nissan 350Z?
The fuse is by the passenger side door behind a plastic cover. The plastic cover has a diagram/schematic of the fuse locations.
