answersLogoWhite

0

Isuzu Axiom

The Axiom is a five-door mid-size sports utility vehicle manufactured by Subaru Isuzu Automotive, Inc. between 2002 and 2004. It features a four-speed automatic transmission, a rear/four-wheel drive layout and is powered by a 3.5-liter V6 engine.

117 Questions

How many miles do you drive before changing your timing belt on a 2003 Isuzu axiom?

80k The above answer is incorrect. The belt requires changing at 100,000 miles under normal conditions. If you drive in severe conditions, then change it at 75,000 miles. Warning: This engine is an Interferance Engine and as such if the belt breaks serious engine damage will occur. Also the water pump is driven by the same belt. To save on future labor costs, replace the water pump at the same time you replace the belt. Considering the average driver is in severe conditions 90% of the time, I wouldn't say incorrect. Just a safe median.

Where is the egr valve on the Isuzu axiom?

Egr valve Isuzu part number(8-17096-178-3 MSRP $197.69) is located on the right side (sitting in vehicle)on top of the intake manifold towards the fire wall.

It is bolted on by two flanged bolts.

Where is a PCV valve located on 04 Isuzu axiom engine?

Isuzu pcv number 8-97289-271-0(MSRP $15.95) is located on the left (driver) vavle cover. On the left VC cover it is closest to the rear of the cover towards the firewall. It will have a hose connection on it leading to the throttle body.

Where is the crank sensor located on a 2004 Isuzu axiom?

Isuzu part number 8-97258-523-0(MSRP $193.86) crank sensor is on the right side(passenger) of the engine block, just behind the mount.

How do you check transmission fluid in 2002 Isuzu axion?

you can't it is a sealed unit. will never have another vehicle with a sealed trans. only way is to have it serviced.

Where is the drain plug on an Isuzu Axiom?

Driver side of engine above the support for the wheel in a concealed area. When you drain the oil spills on the support and splashes.. an oversized flat container is recommended

What can a bad gas cap effect in a 2002 Isuzu Axiom?

Can show vacuum leak as a trouble code. Can show vacuum leak as a trouble code.

Where is the key to remove the tire for a 2002 Isuzu axiom?

It should be in a ziplock type of bag with your jack in the side compartment in the back of the car.

Where is the ac fuse of 02 Isuzu axiom?

In the 2002 Isuzu Axiom, the AC fuse is located in the fuse box, which is typically found under the dashboard on the driver's side or in the engine compartment. To access the fuse, you may need to remove a cover panel. The specific fuse for the AC system is usually labeled in the fuse box diagram, so refer to that for the exact location and amperage rating. Always ensure the vehicle is turned off before inspecting or replacing fuses.

Where is the PCV valve on 2002 isuzu axiom?

On a 2002 Isuzu Axiom, the PCV (Positive Crankcase Ventilation) valve is typically located on the valve cover. It may be found near the rear of the engine, attached to a hose that connects to the intake manifold. To access it, you might need to remove some components for better visibility, but it’s generally a straightforward process. Always consult the vehicle's service manual for specific details.

Where is the transmission dipstick of an Isuzu Axiom located?

I heard someone comment that it has a "sealed" transmission, therefore, a dealer has to add fluid.

I own a 2002 Isuzu axiom. they don't have a dipstick but they do have a holding tank on the right side you check and add fluid there.

How do you change trans fluid to a 2002 Isuzu axiom?

Changing Transmission Fluid
There is no need to change the transmission fluid unless the transmission is used under one or more of the following heavy duty conditions.

  1. Repeated short trips
  2. Driving on rough roads
  3. Driving on dusty roads
  4. Towing a trailer If the vehicle is used under these conditions, change the fluid every 20,000 miles (32,000 km).
  1. Place a large drain pan under the oil pan.
  2. Remove the transmission oil drain screw (2) and drain fluid.
  3. Tighten drain screw (2). Torque: 38 Nm (28 ft. lbs.)
  4. Remove the transmission overfill screw (1) and fill transmission through overfill screw opening, using DEXRON-III ATF. Note: Add transmission fluid until it flows out over the overfill screw opening.
  5. Let engine idle until a fluid temperature between 32°C (90°F) and 57°C (135°F) is reached.
  6. Add transmission fluid until it flows out over the overfill screw opening, then close the overfill screw (1). Torque: 38 Nm (28 ft. lbs.) Note: To prevent fluid leaks, the overfill screw and oil drain screws gasket must be replaced each time these screws are removed. Note: Check transmission fluid temperature with scan tool.


  1. Reset "Oil Life Monitor" data by using Tech 2. Refer to Tech 2 OBD II Connection in Transmission Control System (4L30-E).