0
Jeep Wrangler Sahara
The Wrangler Sahara was a compact sport utility vehicle produced by Chrysler for its Jeep division. This model featured trail cloth seats, alloy wheels, body color fender flares and bumper fog lamps.
1,201 Questions
Why is my gear shifter locked on 87 jeep wrangler?
It happens, if you can't get it to come free by pulling on the shifter, remove the access panel over the shifter, remove the shift handle from the top of the trans and use leverage to free up the linkage. Use a flashlight to see if the linkage bars are all lined up as they would be in neutral, if not manually move the odd one to meet the others.
From what I can figure the little bearings that move back and forth when the gears are shifted, and prevent the wrong one from engaging while you are engaging another can sometimes get stuck half way and freeze up the linkage. Many people can free it up by wiggling and pulling on the shifter, but there are times when it's really stuck and some better leverage is needed.
Will 2007 Jeep Wrangler Sahara 18 inch wheels fit a 2005 Jeep Wrangler Unlimited?
No, the lug pattern changed in between those years and models.
These are the most popular Jeep lug patterns and the vehicles that used them.
5 on 4.5" Bolt Pattern:
- 84-01 Cherokee (XJ)
- 86-92 Comanche (MJ)
- 93-98 Grand Cherokee (ZJ)
- 02-06 Liberty (KJ)
- 97-06 Wrangler (TJ)
- 87-95 Wrangler (YJ)
- 04-06 Wrangler Unlimited (TJ/LJ)
5 on 5" Bolt Pattern:
- 06-08 Commander (XK)
- 99-04 Grand Cherokee (WJ)
- 05-08 Grand Cherokee (WK)
- 07-11 Wrangler (JK)
- 07-08 Wrangler Unlimited (JK)
5 on 5.5" Bolt Pattern:
- 46-86 CJ (All Models)
- 63-73 Full Size Cherokee/Wagonner (SJ)
- 62-71 Galdiator Series Truck (All Models)
What front and rear axles come stock on a 1998 Jeep Wrangler Sahara?
I have a 2001 and it came with a Dana 30 front and a Dana 44 rear
Answer No.2
I have a 1998 Jeep Wrangler (TJ) Sahara. Most came out of the factory with a Dana 30 front axle and a Dana 35C rear axle, though an option of upgrading to a Dana 44 rear was available, they are rare. Most have a stock gear ratio of 3.73.
I cant remember the bellhousing issues off hand, but to let you know, the 4 and the 6's came with different trannys... and Ax-5 and Ax-15 USUALLY...... they are almost.. i stress Almost the same.. i dont see any problems other than the fact that one has an external slave and the other has an internal, but not that big of a deal... lataaaaaaaaaaa and good luck
What type of fluid goes in a 99 jeep wrangler?
Everyone needs to be more specific when asking a question. What fluids? Depends greatly on the application. Transmission , gears , windshield , motor etc.....
Why are all of the gauges out on the 93 wrangler?
the ground for the guages has worked its way loose tighten the ground for the guage cluster.
Will a 2002 Jeep Wrangler soft top fit on a 1994 Jeep Wrangler?
No it should not fit
94 is a YJ and the 02 is a TJ
What bolt pattern is a 1998 jeep wrangler Sahara?
Jeep Wrangler wheel lug patterns years 1987-2006 are 5X4.5
Jeep Wrangler wheel lug patterns years 2007-2014 are 5X5
if its cold out your gear oil is just very thick which makes it hard to shift once the car gets going it should be fine
Why does oil blow out the vent tube?
The answer depends somewhat on the year and model of the bike, but overfilling the oil tank is the most common cause.
Other contributing factors include brittle umbrella valves (only certain years), worn or damaged check ball in the oil pump (only certain models), cam type and worn oil pump scavenger gears.
Will a 2011 Jeep Wrangler wheel fit on a 2003 Jeep Liberty?
any jeep wheel from 2007 and up will not fit and previous older models like 2006-2005 and lower.
the 2007 has a different bolt pattern than the previous year jeeps
What was the green dull paint color called for a jeep wrangler?
LG1 "Sage Green Poly" (low gloss). There was also a dull beige, LJ1 "Sand Beige Poly" (low gloss).
How do you disable the door lamp after removing the doors on the Jeep Wrangler?
Remove the switches
OMG just pull the fuse for the dome light, pretty simple!
How do you replace the blower motor resistor in a Jeep Wrangler TJ?
I'm answering my own question because I found a lot of good information and wanted to simplify it and put it in one spot.
If you're Jeep is starting to lose its fan speeds (the slower ones aren't working and the faster or fastest are) then its most likely going to be your blower motor resistor. A lot of Jeep owners and other owners of Chrystler vehicles have the same problem. It could be a defective resistor or just a short in the system the fries the resistor, I'm not entirely sure.
- At any rate I'll go on with no further delay.
I would head out to your local parts store and pick one of these resistors up, places like autozone can look it up for you, and I recommend them because they have a limited lifetime gaurentee, so if this happens again it should be covered (I hope)
- This is a pretty easy fix. Your blower motor on a TJ is going to be just above where your passengers feet would be. Attatched to the bottom of your dashboard is a bundle of wires that plug into a couple different places. The place you want to focus on is just behind the light that comes on when the door is open, so for starters I removed it to give myself a clear view of what needed to be done and to give me the hand space.
- I used a small socket and a spinner I had in the back of my Jeep for any emergency roadside repairs, but ideally use any tool you're comfortable with, if I recall it might even have take a Phillips head screwdriver.
- With that dropped you can disconnect it (the bulb gets kind of hot) or just push it to the side. Now you're looking at the resistor. It has a red clip that's facing down at you, you have to get that clip to slide so you can release that wire harness from the resistor. I used a Flathead screwdriver and just gently applied tension until it just popped off.
- To release the harness you have to press on the piece the clip was covering, try and take a good look, you should see what needs to move to release it. (but if you're having trouble don't worry, you can contact me and I'll try and help you out)
- With the wire harness out of the way there are only 2 more obstacles in your way, using a ratchet wrench and socket is going to be the best option, unless you have another way of unscrewing something that's at a 90 degree angle from you and is behind a dashboard...
- Undo the 2 screws and the resistor will slide out, that's all that's holding it in there.
- Now take your new resistor and put it in place, and do everything in the reverse. Tighten the 2 screws to lock it, press the harness back into it until it clicks (make sure that black piece is on the bottom) and then snap the red clip back in place to lock it all down.
- Last but not least put your light back in place. I'm going to link some pictures if I can to show you exactly what it should look like.
I put all the bullets in there to seprate, it was hard to read otherwise, don't forget to scroll down and check out the related links for the pictures.
How do you remove the front speakers in a 1993 jeep wrangler Sahara?
think you take the plastic covering off and undo the wires and unbolt it
What type fluid for manual transmission 2002 Jeep Wrangler 4.0L?
I'm pretty sure its 75w-90 with a GL3 rating. The GL5 they have out now is much better then the GL3.
