0
Lexus RX
The Lexus RX series is a group of luxury sports utility vehicles (SUV) distributed by Lexus since 1998. It comprises various hybrid and V6-powered models (like the RX 350, RX 330 and RX 300) equipped with either all-wheel or front-wheel drive.
725 Questions
How do you replace the key Fob battery in the Lexus ES 350?
This link will show you how: http://www.youtube.com/watch?v=Za7pCdUde3U
How can you test the mass air sensor in your 1999 Lexus rx 300?
There are several different things you can do to test it. If your RX runs rough and you suspect the mass, you can unplug it while it's running and see if it runs better with it unplugged. If it does, replace it. You can also tap on the sensor with the vehicle running. If tapping on it makes the engine stumble then replace it. If you have an ohm meter you can check the Resistance across the sensor, but you would have to find out what the acceptable range is for the sensor. You can also take a volt meter to the output lead of the sensor. With the vehicle running and the volt meter on the out put lead you should get a steady voltage output at idle. As you increase throttle the voltage should increase with it. It should increase smoothly and with no "dead" spots. If it doesn't do this or you have a dead spot, replace it. Of course a "live" read from a scan tool would be ideal but most car owners don't have one. Good luck!
How do you turn off maintance light?
If you mean "Check Engine, SES" light, unplug the negative battery for about 1 minute. If if comes back on go to autozone, they'll plug in an OBD2 reader and tell you exactly whats causing it. Also if it stays on you wont pass emssions. (1996 & newer only.)
How do you replace the thermostat located on a 2001 Lexus rx300?
The thermostat on a 2001 Lexus RX300 is replaced by removing the upper radiator hose and unbolting the thermostat housing. The thermostat can then be removed, a new gasket installed, and the replacement thermostat placed in the housing.
How do you reset the maintenance required light on your 2005 Lexus ES330?
try this if it is the reminder light to change your oil and stuff.
1. With your car OFF, place your key in the ignition and turn to "On". Do not start the car.
2. Find the odometer button and press until it reads the total odometer setting, (not the Trip A or Trip B setting).
3. Turn the key to OFF.
4. Place your finger back on the odometer button, press and hold. At the same time, turn the key back to "On".
5. Hold the odometer button in until the MAINT REQD light goes out...should take about 8-10 seconds.
Is Lexus rx 350 only for women?
in my opinion i think all Lexus models are for women. i know alot of women who drive Lexus and i rarley see to many men driving them
What is the angle of departure of the 2009 Lexus RX-350?
The 2009 Lexus RX-350 has a 22.8 degrees angle of departure.
How do you change the rear wiper blades on a Lexus Rx 350?
No model year was given, however as of this writing, all Lexus RX350's have the same rear wiper arm attachment (although the different generations take different lengths of special wiper blades for that arm). See sources and related links below for an installation video and to lookup the correct rear wiper blade. Note these blades are hard to find in stores so you may just want to buy it.
How do you change the automatic transmission fluid in a 2004 Lexus RX 330?
If its out of warranty take it to Toyota dealership and ask for a "drain and fill" Shouldn't cost much more than about 2x the price of an oil change... This drain and fill process only drains about 40% if the fluid since a large part of it remains in the torque converter. After about 3 drain and fills you have in essence replaced all the transmission fluid. I suggest transmission drain and fills be done every 30,000km at least. USE GENUINE TOYOTA TRANSMISSION FLUID type T-IV only......
Why Lexus RX 300 Squeak while driving and turning left?
Follow the steering column down to the floor, there you'll see a u-joint fitting with rubber bushings. Spray there with WD-40 and the squeak will go away.
Where is number 4 cylinder in Lexus rx 300?
Front Center. 2-4-6 Easy targets.
1-3-5 a real pain to get to under the rear manifold...
How do you replace the rear wiper blade on a 2004 Lexus RX330?
You should be able to pop off the 2" plastic gommet from the rear wiper assembly. After doing so you will be able to fully bend the wiper arm and replace the blade. Make sure to reuse the two metal bars for the new blades.
How do you change the rear wiper on 2004-2006 Lexus RX330?
Once you get the correct 2004-2006 Lexus RX330 special rear wiper blade it is very easy to replace. See sources and related links below.
Where is the fuse box on the driver side of a Lexus rx330?
To the left of the brake pedal (also, right behind the parking brake). It's got a black cover protecting it. When you're sitting in the car, it is just beyond your left knee and is a small black box 3"x 6" in size. The cover comes off by prying on the frontal snap.
go to www.lextech.org they have everything you need to replace
How do you replace rear wheel bearing 1999 Lexus rx 300?
There are two different setups for the RX300 rear wheel bearings - front wheel drive and all wheel drive and the parts are different for both. I will talk about what it takes to replace the rear bearing on a 99 - 03 RX 300 all-wheel-drive.
Please note that this is not an easy repair and you will need help and some tools including a press, impact wrench, torque wrench and assorted metric sockets/wrenches.
The bearing is pressed onto the hub and the hub and bearing is then pressed into the spindle.
1. Remove the rear tire - please use a jack stand to secure your work area.
2. Remove the disc break and set aside
3. Remove the router - remove cotter pin bolt keeper and bolt from drive shaft then router (you may need to use penetrating spray)
4. Remove the parking break pads, springs, clips and cable
5. Remove the ABS speed sensor on the inside of the spindle - there is one bolt off to the side of the sensor that is predominately mounted to a metal plate - careful - set aside.
6. You are removing the spindle at this point - remove the lower control arm bolt and sway bar bolts from the lower end of the spindle and then remove the two larger bolts that connect the top part of the spindle to the strut - Please note that your jack or jack stand should NOT BE ON ANY PART OF THE REAR SUSPENSION - it should be hanging freely. At this point you should be able to pull the spindle with the pressed in hub off of the half shaft. You may need to use a hub puller to free the assembly from the half shaft.
7. Using a hydraulic press - press out the hub from the back side and set aside.
8. Remove both inner and outer seals - they are the same and will need to be replace with new ones.
9. On the front side of the spindle, on the inside and holding the bearing in is a snap wring that will need to be remove before the old bearing is pressed out.
10. From the back side of the spindle press out bearing but note that the spindle has a lip that is built in to stop the bearing when it is pressed in - do not push against this outer edge.
11. Now that the old bearing is out - work backwards to re-assemble. It goes back together much quicker than it came apart.
Do not over-tighten the center bolt on the half shaft - it will cause the new bearing to fail. I "think" that the speck was 125 pounds but that may not be correct.
On my '99, it is behind the little compartment door on the left side, just above the hood release latch. When you open that little door, just pull up and it will slide off the hinge pins (it's all plastic) and the fuse panel is right there behind the door. Hope this is the one you're looking for.
