Lexus RX

Remove the wiring harness from the high mount brake light. Remove the back cover of the brake light assembly. Take hold of the brake light connector, push in and turn at the same time. Reverse the process to install the new brake light.

Kate Hodge

The 2010 Lexus RX-350 is 6 ft. 2.2 in. (74.2 in.)12-Speaker Premium Audio System for Navigation wide.

I have a 2001 RX300 and found out it is very easy to change the headlights. From the back, remove the plastic clip holding the wires and bulb casing. Then turn the bulb casing 1/8th turn and remove. The new products have you replace the small plastic casing and bulb in a single unit for about $10. No Tools needed.

i have an is300 also and a got a xenon hid kit on my fog lights, they can be replaced , the bulb type is 9006 (hb4)

Disconnect your battery.

Remove the bolts holding the entire fuse box assembly. (may need to move other mechanicals)

Separate the fuse box housing.

remove the inner cover covering the fuse bolts. (look for where the larger wires go)

Locate and remove the 8mm or 10mm bolts holding the fuse (tight spot under a mess of wiring too).

Replace the fuse.

Reverse the previous steps.

open the glove compartment ,you see a cover,take that off you see the cabin filter,then pull the cabin filter towards you. vice versa instaling it

To load an update DVD to a 2001 LS430 you must first:

Open truck

· Removed carpeted mats

· To the right remove carpeted truck floor panel, about a foot long and a half a foot wide

· You will find a black box that is bolted with two screws on either side of the box

· Remove screws and pull black box free from its location

· On the front of the black box find a slide device and slide to open DVD slot

· Ignition must be engaged

· Push the button under the slide device to eject the DVD

· Insert new DVD and follow instruction on the screen

· Insert black box in the slot and fasten the two screws

Re Replace carpeted mats and you are good to go

y

18 Millimeter, 1.5 Pitch

Aetna provides health insurance including medical, dental, phamaceutical, life, disability and long term health care. Aetna's headquarters is located in Hartford, Connecticut. They have agents available in all states.

Do you mean the cabin air filter? If so it is detailed in the owners manual.

In the trunk, pick up the carpeted panel and under there is the spare tire, jack, and tools.

Just take it to a shop. Nobody gives a sh*t.

Synthetic 0W20

A/F Sensor for Bank 2 Sensor 1. It is the O2 sensor on the front manifold.

A lexus rx 330 2005 uses toyota atf type t-iv fluid

You can reset your engine service light by holding in the scroll button. Hold the button in until the engine oil life goes to 100 percent. The engine service light will go off.

I assume that you are wanting to know how to change the rear brake pads. First, loosen, but do not remove, the lug nuts on the rear wheels. Second, put the rear end up on jacks so that the rear wheels are off the ground. Then remove the rear wheels. Then you are going to see the caliper. On the back of the caliper there is one bolt and a pin attaching the caliper to the main brake assembly. You can tell these from the other bolts because there is a rubber boot around them. Now, you are going to remove the bolt which is on the lower part of the caliper. Once that is removed, the whole caliper will pivot upwards exposing the brake pads (you may have to giggle it a little bit to break it free). The brake pads simply slide out and can be replaced with the new pads. You may have to pry the piston which is part of the caliper back in because you are inserting new brakes. A screwdriver or clamp is handy to help you do this. Now simply repeat these steps in reverse order and you have yourself a new set of brake pads. Good Luck!!

I assume that you are wanting to know how to change the rear brake pads. First, loosen but do not remove the lug nuts on the rear wheels. Second, you are going to need to put the rear end of the car on jacks and then remove the rear wheels. You are now going to be able to see the brake assembly. Locate the caliper (the piece that looks like it is clamped onto the rotor). The top of the caliper is held on by a pin and a bolt. You can tell these from other bolts because there is a rubber accordion-like boot surrounding them. Remove the bolt with the boot (on the lower part of the top of the caliper). Then giggle the top of the caliper and it should pivot upwards exposing the brake pads. The brake pads are held on by clamps so simply wiggle the pads to remove them. You can now insert your new pads in the same way that the old pads were situated. Next you are going to need to push the piston of the caliper back in so that there is room for your new pads. A screwdriver or clamp can help you achieve this. Now all you need to do is pivot the caliper back down, bolt it on, do the same to the other side, put on the wheels, lower the car, and you have yourself a new set of rear brakes. FYI, when you start the car, pump your brakes a few times so that the pistons are compressed once again against the brake pads. Good Luck!!

s

Pull your liner down at the front points of rear bumper and remove the two #10 bolts....take visable bolts and clips off the bottom of cover....lift gate---open storage compartment---remove plastic clips that hold liner and remove liner---remove two black clips that hold trim plate and remove trim plate---there will be 5 #10 bolts inside holes in to remove .....pull cover off! Note: from front points of cover to gate the cover just snaps in.

There is one fuse panel next to the dead pedal on the drivers side of course and there is also one right in front of the battery under the hood. Replacing the fuses under the hood can be very tricky. See your local dealers parts guy for instructions on how to replace these fuses because most of them don't just pull out.

The firing order is 1,2,3,4,5,6. Standing at the front of your vehicle cylinder locations are as follows. Back bank, left to right 1,3,5. Front bank 2,4,6.

It depends on the year of your RX. 2000 and older it is a VVT malfunction. VVT stands for variable valve timing. Check the filter screens on both your oil control valves, this is often the root of VVT issues. If it is 2001 and newer it is a Control Ignition or Misfire code. Hope that helps.

Your front tires are defective. Its time to replaced them.

The DVD player is located in the spare tire well. It's mounted under the rear flooring to the right side of the tire, behind the jack. To eject the DVD, slide the switch cover on the front left side of the player (this opens the DVD slot) and press recessed button. The DVD will then eject.