0
Lunar Eclipses
A lunar eclipse happens when the moon passes behind the earth and into its shadow. The Sun, Moon, and Earth will be lined up, and the Moon will be darkened for a few hours as it passes through the shadow.
431 Questions
When will the next lunar eclipse happen?
See the Sources and related links for NASA web page covering past and future eclipses both lunar and solar.
In 2013 there will be two penumbral eclipses (hardly noticable)
How do you change to Aux on a eclipse model CD3434?
To change to Aux mode on an Eclipse CD3434, press the "Source" button until you reach the Aux input option. Then, use the volume or tuning knob to select and confirm the Aux mode. If there is a dedicated "Aux" or "Input" button, you can also try pressing that to switch to Aux mode directly.
How do you change a water pump 1996 Mitsubishi eclipse?
Here is the procedure, according to the service manual. Sorry, I could not import the figures to reference.
For the 1.6L SOHC:
DESCRIPTION
The water pump on this vehicle is attached to the rear of the power steering pump to form an assembly
(Fig. 27). The water pump/power steering pump assembly is located on the front corner of the engine
(Fig. 29).
The water pump is bolted to the rear of the power steering pump. Driven by the power steering pump
shaft, the water pump's impeller is located inside a die-cast aluminum housing. The water pump housing has a built in outlet. The water pump also has a bolt-on inlet cover with two ports, one for incoming coolant from the radiator and the other for incoming coolant from the heater.
Both pumps (water and power steering) can be serviced separately. Remove the entire water pump/
power steering pump assembly, then disassemble it to service either pump.
For information on the power steering pump, (Refer to 19 - STEERING/PUMP - DESCRIPTION).
REMOVAL
NOTE: Before proceeding, review all Warnings and Cautions (Refer to 7 - COOLING - WARNING) and (Refer to 19 - STEERING - WARNING).
(1) Disconnect battery negative (-) terminal.
(2) Remove the accessory drive belt (Refer to 7 - COOLING/ACCESSORY DRIVE/DRIVE BELT -
REMOVAL).
(3) Remove power steering fluid reservoir. (Refer to 19 - STEERING/PUMP/RESERVOIR - REMOVAL)
(4) Remove generator. (Refer to 8 - ELECTRICAL/CHARGING/GENERATOR - REMOVAL)
(5) Drain engine coolant (Refer to 7 - COOLING/ENGINE - STANDARD PROCEDURE - DRAIN
COOLING SYSTEM).
(6) If equipped with air conditioning, remove A/C compressor upper mounting bolts.
(7) Raise vehicle (Refer to LUBRICATION & MAINTENANCE/HOISTING - STANDARD PROCEDURE).
(8) Remove accessory drive belt splash shield.
(9) If equipped with air conditioning, remove A/C compressor lower mounting bolts. Reposition A/C
compressor to allow access to power steering pump/water pump lower mounting bolts. Do not overextend A/C hoses while performing this.
(10) Remove radiator hose at inlet to water pump.
(11) Remove heater tube hose at water pump.
(12) Lower vehicle.
(13) Remove the bolt fastening the power steering pressure hose to the reservoir bracket (Fig. 28).
(14) Back out the tube nut securing the power steering fluid pressure hose to the power steering pump and remove the hose from the pump (Fig. 28). Cap off hose end and pump pressure port.
(15) Remove coolant outlet connector hose at water pump outlet.
(16) Remove all four power steering pump mounting bolts. (Fig. 29)
(17) Remove power steering pump and water pump as an assembly.
(18) To separate the power steering pump from the water pump, (Refer to 7 - COOLING/ENGINE/WATER PUMP - DISASSEMBLY).
(19) If the power steering pump pulley needs to be removed, (Refer to 19 - STEERING/PUMP - DISASSEMBLY).
DISASSEMBLY
(1) Remove the three hex drive bolts and washers that attach the power steering pump to the water
pump (Fig. 27).
(2) Use the following steps to access the water pump impeller hex.
(a) Place a 1⁄4 inch drive 10 mm socket in through the coolant inlet tube, then back it into the heater hose fitting area as shown (Fig. 30). Backing the socket into the heater hose fitting makes it easier to perform the following step.
(b) Holding the socket in this position, insert a 1⁄4 inch drive extension (6 inches in length or longer) in through the heater hose fitting into the rear of the 10 mm socket.
(c) Push the socket with the extension into the pump placing the socket on the hex built into the
center of the water pump impeller.
(3) While holding the power steering pump shaft from turning using a hex wrench in the pulley end of
the shaft, loosen the impeller by rotating the 1⁄4 inch drive extension counterclockwise using a ratchet. The water pump will rise off of the power steering pump as the impeller is rotated.
(4) Once the threads have been disengaged, remove the entire water pump assembly from the power steering pump. If the water pump will be used again, the 10 mm socket and extension can be left inside the water pump until reassembly is completed.
(5) If the water pump inlet cover needs to be removed, remove the seven fasteners around the perimeter of the pump and remove the cover. Discard the housing O-ring type seal.
(6) If the power steering pump pulley needs to be removed, (Refer to 19 - STEERING/PUMP - DISASSEMBLY).
NOTE: For reassembly, (Refer to 7 - COOLING/ENGINE/WATER PUMP - ASSEMBLY).
ASSEMBLY
(1) If the water pump inlet cover needs to be installed on the water pump:
(a) First apply Mopart Dielectric Grease or equivalent to a NEW water pump O-ring seal.
(b) Place the O-ring seal in the housing groove where the cover contacts the housing.
(c) Install the seven fasteners around the perimeter of the pump. Tighten them to 12 N·m (105 in.lbs.) torque.
(2) If a pulley needs to be installed on the power steering pump, (Refer to 19 - STEERING/PUMP -
ASSEMBLY).
(3) Place the water pump assembly onto the power steering pump shaft.
(4) Rotate the water pump so the water pump outlet is near the water pump upper mounting holes
(hole with dowel guide). Arrange the three pump fastener holes so they line up.
(5) If the water pump impeller hex has not been accessed with a socket, use the following steps to
access the water pump impeller hex.
(a) Place a 1⁄4 inch drive 10 mm socket in through the coolant inlet tube, then back it into the heater hose fitting area as shown (Fig. 30).
(b) Holding the socket in this position, insert a 1⁄4 inch drive extension (6 inches in length or longer) in through the heater hose fitting into the rear of the 10 mm socket.
(c) Push the socket with the extension into the pump placing the socket on the hex built into the center of the water pump impeller.
(6) While holding the power steering pump shaft from turning using a hex wrench in the pulley end of
the shaft, tighten the water pump impeller rotating the 1⁄4 inch drive extension clockwise using a ratchet. This will draw the water pump in toward the power steering pump. Tighten the impeller to 26 N·m (19 ft. lbs.) torque.
(7) Remove the 10 mm socket, 1⁄4 inch extension and ratchet from the water pump. Remove the hex
wrench.
(8) Align the three pump fastener holes and install the three hex drive bolts with washers (Fig. 27).
Tighten the bolts to 26 N·m (19 ft. lbs.) torque.
(9) Install assembly on the vehicle. (Refer to 7 - COOLING/ENGINE/WATER PUMP - INSTALLATION)
INSTALLATION
NOTE: Water pump and power steering pump must be attached to one another before installation in vehicle. For proper procedure, (Refer to 7 - COOLING/ ENGINE/WATER PUMP - ASSEMBLY).
(1) Install water pump/power steering pump assembly into engine compartment in reverse of how
it was removed.
(2) Install all four power steering pump mounting bolts (Fig. 29). Tighten bolts to 28 N·m (21 ft. lbs.)
torque.
(3) Install coolant outlet connector hose at water pump outlet. Install clamp.
(4) Using a lint free towel, wipe clean the open power steering hose end and the power steering
pump port. Replace the used O-ring with new. Lubricate the O-ring with power steering fluid.
(5) Attach the power steering fluid pressure hose to the pump outlet port (Fig. 28). Do not tighten the
tube nut at this time.
(6) Install the bolt fastening the power steering pressure hose to the reservoir bracket (Fig. 28).
(7) Tighten power steering pressure hose tube nut at power steering pump to 28 N·m (21 ft. lbs.) torque.
(8) Raise vehicle.
(9) Install heater tube hose at water pump fitting. Install clamp.
(10) Install radiator hose at inlet to water pump. Install clamp.
(11) If equipped with air conditioning:
(a) Position A/C compressor, align mounting holes and install, but do not fully tighten, A/C compressor lower and upper mounting bolts.
(b) Lower vehicle.
(c) Tighten A/C compressor upper mounting bolts to 28 N·m (21 ft. lbs.) torque.
(d) Raise vehicle.
(e) Tighten A/C compressor lower mounting bolts to 28 N·m (21 ft. lbs.) torque.
(12) Install drive belt splash shield.
(13) Lower vehicle.
(14) Install generator (Refer to 8 - ELECTRICAL/CHARGING/GENERATOR - INSTALLATION).
(15) Install power steering fluid reservoir. (Refer to 19 - STEERING/PUMP/RESERVOIR - INSTALLATION)
(16) Install accessory drive belt (Refer to 7 - COOLING/ACCESSORY DRIVE/DRIVE BELT -
INSTALLATION).
(17) Connect battery negative (-) terminal.
(18) Fill cooling system (Refer to 7 - COOLING - STANDARD PROCEDURE - FILLING COOLING
SYSTEM).
(19) Perform POWER STEERING PUMP INITIAL OPERATION procedure. (Refer to 19 - STEERING/
PUMP - STANDARD PROCEDURE)
(20) Check for leaks at all hose connections.
(Accents are intrusions of a mother language into an acquired language, as when a Mexican or Russian speaks English. Dialects are variations of a language, such as British English, Australian English, American English and so on with each of these huge dialectical entities having subdialects in them.) According to MSN Encarta, "Dialects develop primarily as a result of limited communication between different parts of a community that share one language. Under such circumstances, changes that take place in the language of one part of the community do not spread elsewhere. As a result, the speech varieties become more distinct from one another. If contact continues to be limited for a long enough period, sufficient changes will accumulate to make the speech varieties mutually unintelligible. When this occurs, and especially if it is accompanied by the sociopolitical separation of a group of speakers from the larger community, it usually leads to the recognition of separate languages. The different changes that took place in spoken Latin in different parts of the Roman Empire, for example, eventually gave rise to the distinct modern Romance languages, including French, Spanish, Portuguese, Italian, and Romanian." For specifics on how the Southern dialect emerged and is viewed today, the following is an interesting discussion: http://www.pbs.org/speak/seatosea/americanvarieties/southern/sounds/ For specifics on how the Southern dialect differs from Standarad American English, see http://en.wikipedia.org/wiki/Southern_American_English.
What are the 4 elements necessary to marketing occur?
The four elements necessary for marketing to occur are the product or service being marketed, the target audience or customer segment, the communication channel or medium to reach the audience, and the strategies to promote, advertise, and sell the product or service.
At maximum, it can take several hours, but the timing depends on the alignment of the Sun, Earth and Moon. If the Moon is near "perigee", when it is closest to the Earth, the eclipse will take longer; when the Moon is farther away, at "apogee", then the eclipse is shorter.
The NASA Eclipse Web Site has complete details on all eclipses from 2000 BC to 3000 AD.
The average household owns 5 of these every year What are they?
The average household owns 5 televisions every year.
What is most likely the cause of a small evap system leak on a 1997 Mitsubishi Eclipse RS?
it happened to my Honda Accord yesterday also. Friend of mine used scanner to detect that problem and found out that the part name "Purge system solenoid valve" was broken. I hope this will give you a hint for your car. Thia problem can also be caused by an improperly installed air filter housing. The housing may not be sealed properly on its gaskets or the holding clips may not be set. It is an easy item to check! You may want to check your charcoal canister also...I had the same problem just two month's ago and that was the problem...I have a 99 Eclipse RS Spyder.... it is your roll over valve on the fuel tank i have a 97 rs too it had the same problem I would start with making sure you have a good seal on your gas cap as well (three clicks whenever it is removed and put back on). This is one of the most common causes of this code. Also, check all your vaccum lines for cracks from the gas tank to the evap system. Another cause, as mentioned above, is the purge solenoid sensor.
What time will southwest Florida be able to see the lunar eclipse?
In southwest Florida, the lunar eclipse will be visible on November 19, 2021, starting at around 2:18 a.m. Eastern Time and reaching its maximum at around 4:02 a.m. Eastern Time. This eclipse will be a partial lunar eclipse, and the moon will set before the eclipse ends.
When will the next lunar eclipse be and when will it be the end of the world?
People who know what they're talking about are saying things like 5 billion years from now, but that's just the end of Planet Earth. Nobody really knows about humanity itself. I mean, in billions of years humans could not be human at all (see Doctor Who; that episode with Rose and the Doctor with funny ears on that end-of-earth viewing platform). You see? Even Doctor Who has answers... As for the next lunar eclipse, depends where you live. Maybe try being more specific next time. ____________________________ The end of the world is sure to happen in your lifetime. Every time a person dies, it is the end of the world for that individual. Apart from that, there is no need to worry. Nothing will happen to you or to anyone else that is not common to mankind.
What math did Benjamin Banneker use to predict solar ad lunar eclipses?
Benjamin Banneker used trigonometry and advanced mathematical calculations to predict solar and lunar eclipses. He referred to mathematical tables and made observations of celestial bodies to estimate their positions and movements accurately. His predictions were notable for their accuracy and were used by others for navigation and astronomical purposes.
Last date of lunar eclipse in England?
Lunar eclipses aren't rare; you'll see them every other year or so, on average. Looks like the most recent total lunar eclipse visible from England was February 21, 2008.
Do people in earths umbra see in a total lunar eclipse?
No, they see night-time. You can see a lunar eclipse (from anywhere) when the MOON is in the earth's umbra.
What really happens during an eclipse?
After Eclipse, you can read Breaking Dawn, the 4th book to the saga, and supposedly the last. First part is a long descriptive summary. Second part at the bottom is a simple bullet pointed summary with alot less words to read.
Descriptive and long summary of Breaking Dawn (WARNING: I summarized just about everything. So if you want to be surprised while reading Breaking Dawn, I suggest you DONT read this. But if you want to know just about everything, read it.):
In Breaking Dawn, Bella Swan encounters a series of events. Her and Edward's wedding finally play out and Bella get's her final human demand. (sex with Edward) After spending their honeymoon together on Isle Esme, Bella discovers that after a few sexual intercorses with Edward, she is pregnant! But, how can a baby already be showing on Bella's stomach? They rush home to Forks, Washington only to find that the baby is half vampire. He or she starts sucking the life of Bella away one day at a time. Edward suffers the suspense of not knowing when the baby will finally be ready to survive on it's own, and how to exit the mothers body is not described pleasantly. Although Carlisle could easily remove the baby without inflicting any harm to Bella, she refuses repeatedly. She believes that she will survive labor, even when the baby will tear it's way through her stomach to be free. She becomes very weak and unable to provide food for herself, it seems as if the baby won't allow any of it into it's stomach. They discover that if Bella drinks blood, she can get the nutrients she needs in order to survive. Like Bella, she accidentaly spills the cup of blood and automatically reaches to catch it. Not a good move. When she had reached to save the bright red liquid from staining the white carpet, the placenta detatched, resulting in a suffocating baby. Bella goes into complete shock as the blood she had forced down began to come back up. Thankfully, Edward successfully retreaves the baby (a baby girl named Renesmee). But, saving Bella from dying is a whole new matter. He quickly fills her veins with vampire venom and morphine. Bella narrates a descriptive chapter of how badly the fire burned inside her as she desperately tried to hang onto dear life like she had promised them. The venom saves her as she wakes up as a beautiful vampire. She learns the basics of becoming a vampire, resisting the urge to drink Charlie's blood when he comes over to visit. But, something rare for a vampire which Bella holds, is how she can act like a three hundred year old vampire. (Not being crazy for blood like a new born) She can easily distract herself from something, such as killing humans. After a while, she receives a message that the Volturi, the entire guard including the wives, are coming to investigate the new baby. Before the Volturi can kill Nessie, Alice shows up after running away earlier in the story, preventing the death of Nessie. Finally, Edward and Bella and Nessie can all enjoy their small, but perfect piece of their forever.
Short and sweet summary of Breaking Dawn:
*Edward and Bella get married
*Bella gets pregnant during her honeymoon with a half human half vampire baby
*They save Bella before Renesmee can kill her during labor
*Bella is transformed into a vampire
*Volturi come to kill Nessie
*Alice and Bella both save them all from being killed
*They all live happily ever after
THE END
don't ruin the book for me, anyway to have to read to the short second life of bree tanner first it's so cool
Explain why lunar eclipses occur during a full moon?
A lunar eclipse can only occur during a full moon because the lunar eclipse causes the Moon to pass directly behind the Earth and into its shadow. This can occur only when the Sun, Earth, and Moon are aligned exactly, or very closely with the Earth in the middle.
What is the difference between a lunar eclipse and the moon phases?
Eclipses involve a shadow from one object to another. Moon phases involve the moons own shadow on itself because part of the moon may be in the shade so we can't see it. During a full moon we see all of the moon lit up by the sun.
What does it mean if you are born during a lunar eclipse?
In astrology, being born during a lunar eclipse is said to amplify the energy of the full moon, bringing about heightened emotions and a greater emphasis on endings and beginnings. Some believe that individuals born during a lunar eclipse may experience intense inner transformations and a strong connection to their emotions.
How often does a full moon lunar eclipse happen?
A full moon lunar eclipse happens approximately twice a year.
When is the next lunar eclipse set to occur?
According to Astronomy Essentials and Earth Sky, the next lunar eclipse should arrive on April 25th, 2013. It's only a partial eclipse, and it will only last 27 minutes.
What time is the lunar eclipse tonight in Louisiana?
NOW. IT IS STARTING NOW!
Depending on your time zone, the total lunar eclipse will begin either every early the morning on Tuesday, December 21, or very late the evening of Monday, December 20.
In the table below, All times are in UCT, "Coordinated Universal Time" which used to be called Greenwich Mean Time. For the Eastern time zone, subtract 5 hours; for Central time, things happen 6 hours earlier. Mountain Time is 7 hours earlier, and subtract 8 hours for Pacific time.
Penumbral Eclipse Begins: ____05:29:17 UT
Partial Eclipse Begins: _______06:32:37 UT
Total Eclipse Begins: ________07:40:47 UT
Greatest Eclipse: ___________08:16:57 UT
Total Eclipse Ends: _________08:53:08 UT
Partial Eclipse Ends: ________10:01:20 UT
Penumbral Eclipse Ends: _____11:04:31 UT
How do you safely view a lunar eclipse?
Precautions must be taken to avoid damage to the eyes while observing a solar eclipse ...
an eclipse of the sun.
No such caution is required while viewing a lunar eclipse. You can freely look at the moon
as much as you wish, whether or not it's in the process of being eclipsed, provided, of course,
that your attention is not required elsewhere ... on the road ahead of your car, for example.
When and where will the next lunar eclipse happen in the northern hemisphere?
There are slightly more than one and a half partial or total lunar eclipses per year, on average. However, you can't see them if they occur when it's daytime where you are, so the number you can see is a bit less.
A person living in a given spot can reasonably expect to see a lunar eclipse slightly less often than once per year, weather permitting.
Why are lunar eclipses often seen?
Do you mean the book by Stephanie Meyer? Because, if you do, Edward refers to "Eclipse" because he's competing against Jacob, he being the sun and Jacob being the moon, therefore making it an eclipse because Bella can't choose whom she loves more.
Hope this answered your question.
-Esme
