0
Machinery and Tools
The Machinery and Tools category covers questions regarding hand tools, power tools, workshop machinery (such as lathes, milling machines, etc), welding and cutting tools and equipment, measuring instruments, earth-moving machinery, furnaces, factory and industrial machinery.
1,597 Questions
What filler metal is used to weld 308 stainless steel?
dissimilar steel grades and the unknown grade ss can easily welded with the help of
680CGS lnt welding electrode
Why you use of segregated plate?
Segregated plates seem to be used most in situations in which a selection of foods is to be reheated just prior to serving. For instance, meals on airplanes are usually served on segregated plates, presumably to prevent the various food items on the plate from intermingling. Similarly, ready-prepared frozen meals are also packaged in segregated plates for the same reason.
The speed of the machine is tied to the power supply frequency and the number of poles the machine has. It becomes impractical to make a round rotor machine with many poles, so machines that spin at low revolutions will typically be salient designs. A two or four pole machine could be round rotor designs.
Is there a general-purpose drill bit that can really do the job on wood metal concrete and more?
The ARTU German Drill bits are suitable for all materials.
One drill bit will do all your work whether you are a DIY. trades person or farmer.
Concrete, masonry, hardened steel, glass, ceramic, wood and many other surfaces can be drilled easily.
Special negative grinding on the tip means, no drifting during initial drilling. No centre punch needed - eliminates "walking. Enables the tip to bore through with a filing rather than a boring action.
The tip is a blend of titanium and tungsten carbide for maximum hardness & resistance to heat & water.
Chrome vanadium shank provides extra hard strength.
High tech bonding allows temperatures of up to 1000 deg.
You can now drill brick into steel, wood into brick and concrete in bar steel without damaging the tip.
Can be re-sharpened using a high quality grinding wheel.
For More Information PLEASE CALL:
ASIA'S BEST INDUSTRIAL SALES CORP.
Manila: 0932.879.5528
Cebu: (032) 231.2158; 233.6436; 232.6875
emails: asiasbestmanila@gmail.com and asiasbestcebu@yahoo.com
Which tool is used to loosen or tighten cross-head screws?
A crosshead screwdriver or scocket set with a crosshead screw driver bit attached. Screwdrivers routinely used are Pozidriv and Phillips
What are the types of tool post?
the types of tool post on lathes can be classified as
single screw tool post
four bolt tool post
open side tool post
four way tool post
How many megohms need to run a motor?
A megohm is a unit of resistance to the flow of electricity. The requirements of motors are given in terms of voltage, current, whether they are direct or alternating current and, if alternating current, the number of phases.
Which is stronger a long rope or short rope?
Technically it doesn't matter. The length of a rope has no impact upon its breaking point and its strength. How the rope is anchored and any knots used is most important and usually will be responsible for the breaking point.
Rope has a lot of purposes, all depending on what you want to achieve by using it. There are a variety of types of rope for different purposes.
Is there a difference between diesel fuel used in cars and furnaces?
Yes, the home heating fuel is of a lower quality or cetane rating than that used for an automobile.
also home fuel is not taxed thats why it is dyed red so they cant sell it for autos it will run fine. cetane booster is 4 bucks. by me truckers are tested for red fuel. dont even ask what the fine is many people have 500 gallons in a above ground tank and fill there car as needed at a 1.50 less a gall. cars are not tested in nj so makes you think youcouldnt tell the difference in performance or smoke just color
What kind of songs are for the jump rope?
Here are a few jump rope songs that I know:
Cinderella:
Cinederella,
Dressed in yella,
Went upstairs to kiss a fella,
By mistake,
She kissed a snake,
How many doctors did it take?
1,2,3,4,5,6...
Had a Little Race Car:
Had a little race car
1994
Went around the
coooooooooooooooorner
(as coooooorner is being said the jumper jumps out runs to the other side of the rope and jumps back in)
Slammed on the brakes
But the brakes didn't work.
Ran into a lady
Ran into a man
Ran into a police man
Man oh man
He put you in jail
How many gingerales did you drink?
1,2,3,4,5,6...
Texico Mexico:
(swingers swing rope only under the jumper)
Texico
Texico
Over the hills
(swingers swing rope over now)
From Mexico
Where they do the
(jumper jumps with legs spread out to the sides)
Splits Splits Splits
And the high heeled
(jumper sticks one foot forwards as they jump)
Kicks Kicks Kicks
And they
(jumper turns around)
Turn around, round, round
And they
(jumper touches the ground)
Ground Ground Ground
And they
(jumper holds hands in the shape of a book)
Read a book book book
And
(jumper closes their eyes)
Do not look look look
And count to ten ten ten and
that's the end end end/start again gain gain
1,2,3,4,5,6,7,8,9,10
Fudge Fudge:
Fudge Fudge
Call a judge
players name having a baby
their boyfriend/girlfriend's going crazy
the baby will be a
(repeat the following until the jumper messes up)
Boy
Girl
Alien
Monster...
Strawberry Shortcake:
Strawberry shortcake
Huckleberry pie
Who will be your lucky guy/gal
(say the alphabet)
Tinker Tailer *requires a large number of people*:
(each person jumps in and then runs out, there is no missing beats, there is always someone in the rope)
Tinker
Tailer
Soldier
Sailer
Rich man
Poor man
Begger man
(the their jumps three times)
Their Theif Theif
Doctor
Lawyer
Indian
(Chief stayes in three times)
Chief chief chief!
What does CRC mean in relation to CNC programming?
CRC refers to "Cutter Radius Compensation". To ensure compliance to the drawing specification of a machined radius, the tip radius of a cutting tool has to be taken into account to compensate for the actual required value of a radius when it is programmed into the CNC.
