Mitsubishi Eclipse

To replace the bulb on a 2007 Mitsubishi Eclipse, first, open the hood and locate the headlight assembly. Remove the plastic cover or the retaining clips to access the bulb. Disconnect the electrical connector from the old bulb, then twist the bulb counterclockwise to remove it. Insert the new bulb, reconnect the electrical connector, and replace any covers or clips.

The automatic transmission relay for a 1998 Mitsubishi Eclipse 2.0 non-turbo is typically located in the engine compartment fuse box. You can identify it by checking the diagram on the fuse box cover, which will indicate the specific position of the relay. If you're having trouble locating it, consulting the vehicle's service manual can provide additional guidance.

To change the drive belt on a 2002 Mitsubishi Eclipse GT, start by disconnecting the negative battery terminal. Then, remove the engine cover and locate the drive belt tensioner; use a socket or wrench to relieve tension and slide the belt off the pulleys. Install the new belt by routing it according to the belt diagram usually found on a sticker in the engine bay, then reapply tension on the tensioner. Finally, reconnect the battery and start the engine to ensure everything is functioning properly.

The compression pressure for a 1998 Mitsubishi Eclipse GST, which features a turbocharged 2.0L inline-four engine, typically ranges from 160 to 190 psi across the cylinders. Variations can occur due to factors such as engine wear, maintenance history, and modifications. It's important to ensure that the values are consistent across all cylinders for optimal engine performance. If compression readings are significantly lower, it may indicate issues such as worn rings or valves.

The 2001 Mitsubishi Eclipse GT is equipped with a 3.0-liter V6 engine. This engine produces 200 horsepower and is paired with either a five-speed manual or a four-speed automatic transmission. The V6 provides a balance of performance and efficiency for the sports coupe.

To replace the timing belt on a 1997 Mitsubishi Eclipse, first ensure the engine is cool, then disconnect the battery. Remove the timing belt cover, and align the timing marks on the crankshaft and camshaft to the TDC position. Next, loosen the tensioner, remove the old belt, and install the new timing belt, making sure it's correctly aligned. Finally, re-tension the belt, replace the covers, and reconnect the battery.

To fix a sunroof in a 2000 Mitsubishi Eclipse, first, inspect the sunroof for any debris or obstructions that may be preventing it from opening or closing properly. Check the sunroof motor and switch for functionality; if either is faulty, they may need replacement. Lubricate the tracks and ensure the seals are intact to prevent leaks. If the issue persists, consult a repair manual for further troubleshooting or consider seeking professional help.

Engine mounts on a 2003 Mitsubishi Eclipse Spyder typically need to be replaced when they show signs of wear, such as excessive engine movement, vibrations, or unusual noises. While there is no specific mileage interval for replacement, it's generally advisable to inspect them every 50,000 to 100,000 miles or if any symptoms arise. Regular maintenance checks can help identify issues early and ensure a smoother driving experience.

The ads relay, or air conditioning relay, on a 2001 Mitsubishi Eclipse is typically located in the engine compartment fuse box. To find it, open the fuse box cover and look for a relay labeled for the air conditioning system. If you're unsure, refer to the vehicle’s service manual for the exact location and diagrams.

To remove the glove compartment on a 2003 Mitsubishi Eclipse, start by opening the glove compartment and removing any contents. Next, locate and remove the screws that secure the glove compartment to the dashboard; these are typically found along the top and sides. Once the screws are removed, gently pull the glove compartment out, ensuring to disconnect any attached cables or lights before fully detaching it from the vehicle.

The 2007 Mitsubishi Eclipse typically requires about 4.5 quarts of oil when equipped with a 2.4L engine and about 5 quarts for the 3.8L V6 engine, including the oil filter replacement. Always consult the owner's manual for the specific model and engine type to ensure accurate information.

On a 1991 Mitsubishi Eclipse, the starter is located on the lower side of the engine, near the transmission. Specifically, it can be found on the right side of the engine block, close to the rear. To access it, you may need to lift the vehicle and remove any obstacles, such as the engine cover or heat shield, for better visibility and access.

For a 1995 Mitsubishi Eclipse GSX, the torque specifications vary by component. Generally, the engine block main bearing bolts should be torqued to about 75 ft-lbs, while the cylinder head bolts typically require around 65 ft-lbs in several stages. It's important to refer to a service manual for detailed specifications and sequences to ensure accuracy and avoid damage. Always use a calibrated torque wrench for best results.

To reprogram a keyless entry remote for a 2001 Mitsubishi Eclipse Spyder, first, get into the vehicle and close all doors. Insert the key into the ignition and turn it to the "On" position (not starting the engine) and then back to "Off" five times within ten seconds. After the fifth turn, the doors should lock and unlock, indicating the vehicle is in programming mode. Press any button on the remote you wish to program; the doors will lock and unlock again to confirm successful programming.

To remove the intake manifold on a 2001 Eclipse GT, start by disconnecting the negative battery terminal to prevent electrical shorts. Next, remove any components obstructing the manifold, such as the air intake duct, throttle body, and vacuum hoses. Then, unbolt the intake manifold from the engine, making sure to label or take note of where each bolt goes. Finally, gently lift the manifold off the engine, being cautious of any remaining gaskets or seals that may need replacement.

To install glow gauges in a 1996 Eclipse, first, remove the dashboard panel by unscrewing the necessary screws and gently prying it off. Next, take out the existing gauge cluster by unscrewing it and disconnecting the wiring harness. Replace the stock gauge faces with the glow gauges, ensuring they are properly aligned, and reconnect the wiring harness. Finally, reassemble the gauge cluster and dashboard, and test the new gauges to ensure they light up correctly.

To adjust the timing on a 1991 Plymouth Laser RS non-turbo, first ensure the engine is at operating temperature and then turn it off. Locate the timing mark on the crankshaft pulley and the timing scale on the engine. Use a timing light to check the current timing; connect the light to the number one cylinder spark plug wire. If adjustment is needed, loosen the distributor clamp bolt and rotate the distributor until the timing light indicates the correct timing mark, then tighten the bolt to secure the distributor in place.

The spark plugs on a Mitsubishi Endeavor are located on the engine cylinder head. To access them, you'll need to remove the engine cover and the ignition coils, which sit directly above the spark plugs. The Endeavor typically has a V6 engine, with the spark plugs positioned in a line along each side of the engine. Always consult the vehicle's service manual for specific details related to your model year.

To adjust the headlights on a 1998 Eclipse, first park the car on a level surface about 10-25 feet from a wall. Turn on the headlights and mark the center of the beam on the wall with tape. Then, using a screwdriver, adjust the vertical and horizontal alignment screws located on the headlight assembly until the top of the beam is at or just below the tape mark and the beam is centered horizontally. Finally, check both headlights to ensure they are aligned correctly.

In "The Fast and the Furious" (2001), two Mitsubishi Eclipse RS cars were prominently featured. Both vehicles were modified for the film and showcased in various racing scenes. These cars played a significant role in establishing the film's street racing culture.

To replace the third brake light bulbs in the spoiler of a 1995 Mitsubishi Eclipse, first, remove the screws or clips securing the brake light assembly to the spoiler. Carefully pull the assembly away to access the bulbs. Twist the bulb sockets counterclockwise to remove them, then replace the old bulbs with new ones, ensuring they are securely in place. Finally, reattach the assembly and secure it with the screws or clips.

On a 1997 Mitsubishi Eclipse with a 2.4L engine, the crankshaft position sensor is typically located near the bottom of the engine, mounted on the engine block or near the flywheel. You will generally find it on the driver's side, close to the transmission bell housing. To access it, you may need to remove some components for better visibility and access. Always refer to a repair manual for specific details and diagrams.

On a 2008 Mitsubishi Eclipse, the oxygen sensors are located in two main areas: one upstream (pre-catalytic converter) and one downstream (post-catalytic converter). The upstream sensor is typically found on the exhaust manifold or just before the catalytic converter, while the downstream sensor is located after the catalytic converter in the exhaust system. To access them, you may need to lift the vehicle for better visibility and reach.

The bolt pattern for the Mitsubishi Eclipse varies by model year and trim. Generally, most models have a 4x100 mm bolt pattern. However, some later models, particularly the Eclipse GS and GSX from the 2G generation, may have a 5x114.3 mm pattern. It's important to verify the specific year and trim to ensure accuracy.

To install a boost controller on your 1998 Mitsubishi Eclipse GST, first, make sure the engine is off and cool. Locate the boost source line, which typically runs from the turbocharger to the wastegate actuator, and disconnect it. Connect the boost controller according to its specific instructions, ensuring the lines are secure and leak-free. Finally, recheck all connections, start the engine, and monitor boost levels to ensure proper operation.