Mitsubishi Lancer

it is located, or rather mounted on your air intake system. Whether the intake is an aftermarket part of oem the IAT sensor/connectors are usually on the manifold of the intake.

A car may take longer to start in extreme cold, especially if it has an older, weaker battery. In any temperature, a car will take longer to start if it has a dying battery.

Three

usaully by unbolting it from the engine and dropping it down, what year and what engine?

There are adjusting screws on the top and side of each headlight. I like to get on a really dark road at night and set them to how I like them without blinding oncoming drivers.

That might depend on the year Lancer you're talking about.

For my 2008 GTS, my fuel filter is located inside my fuel pump, meaning when I have to replace the filter, I've got to replace the pump. I don't know how long Mitsubishi has been doing this, so you might be in the same boat as me.

Mobile One Synthetic for High Milage engines

The best gasoline for a Mitsubishi Lancer typically depends on the specific model and engine type. For most models, regular unleaded gasoline with an octane rating of 87 is recommended. However, if you have a performance-oriented version like the Lancer Evolution, premium gasoline with a higher octane rating (usually 91 or higher) is advised to maximize performance and efficiency. Always consult the owner's manual for the best fuel recommendations for your specific vehicle.

In a 2004 Mitsubishi Lancer, the fuel pump relay is typically located in the engine compartment fuse box. To find it, open the hood and look for the fuse box near the battery. The specific relay for the fuel pump is usually labeled on the cover of the fuse box. If you're having difficulty, consult the owner's manual for exact locations and diagrams.

To remove the steering wheel cover on a 1995 Mitsubishi Lancer, first, disconnect the negative battery terminal to prevent accidental airbag deployment. Next, use a flathead screwdriver to carefully pry off the plastic cover surrounding the steering wheel. Once removed, locate and unscrew the retaining screws for the steering wheel cover, then gently pull it off the steering wheel. Be cautious of any wiring connected to the airbag and ensure proper handling.

To change the timing belt on a 2003 Mitsubishi Lancer, first disconnect the battery and remove the accessory belts. Next, drain the coolant and remove the radiator for better access. Align the timing marks on the crankshaft and camshaft, then remove the old timing belt, tensioner, and idler pulleys. Install the new timing belt, ensuring proper tension, reassemble the components, refill the coolant, and reconnect the battery.

The Mitsubishi Lancer typically uses automatic transmission fluid (ATF) that meets specific specifications depending on the model year and transmission type. For most models, the recommended ATF is Mitsubishi's own DiaQueen ATF, often referred to as SP-III or SP-IV, with variations based on the transmission design. It's essential to consult the owner's manual or a dealership for the exact fluid type and specifications for a specific Lancer model.

The output speed sensor on a 2004 Mitsubishi Lancer is typically located on the transmission. Specifically, it can be found on the side of the transmission case, often near the output shaft or in the area where the transmission meets the engine. To access it, you may need to remove any components obstructing the sensor's location. Always consult a repair manual for precise details and diagrams.

A tinny noise after fitting extractors on your 2004 Lancer could be due to several factors. Common causes include improper fitting or alignment of the extractors, which can lead to exhaust leaks and vibrations. Additionally, the material and design of the extractors may amplify certain sounds, causing a tinny resonance. It's advisable to check for leaks and ensure all connections are secure and properly torqued.

The part number for a 2002 Mitsubishi Lancer ashtray is typically 7802A013. However, it's always best to verify this with a dealer or parts supplier, as part numbers can vary based on specific model variations or regional differences.

To change the brake light on a 2007 Mitsubishi Lancer GLX, first, open the trunk and locate the tail light assembly. Remove the screws or clips securing the assembly, then gently pull it out. Twist the bulb socket counterclockwise to release it, replace the old bulb with a new one, and reassemble the tail light by reversing the steps. Test the new brake light to ensure it’s working properly.

In a 1997 Mitsubishi Lancer, the spark plugs are located on the engine cylinder head. Depending on the specific engine configuration, you may find them on the top of the engine, typically beneath a plastic or metal cover. To access them, you'll need to remove the ignition coils or wires, which are connected to each spark plug. Make sure to consult the vehicle's manual for specific details related to your engine type.