answersLogoWhite

0

Toyota MR2

The Toyota MR2 was a two-seat, rear-wheel drive (RWD) sports car manufactured by Central Motors, a member of Toyota Group. Produced in 1984-2007, this model featured transverse-mounted I4 engines and McPherson strut rear and front suspensions.

543 Questions

How do you put the top down on a mustang?

To put the top down on a Mustang convertible, first ensure the vehicle is parked on a level surface and the engine is running or in accessory mode. Locate the convertible top switch, usually found on the center console or dashboard. Press and hold the switch in the direction indicated to lower the top, and release it once the top is fully down. Always check your owner’s manual for any specific instructions or precautions related to your particular model year.

How do you get to battery on mr2?

To access the battery on a Toyota MR2, you typically need to open the rear trunk, as the battery is located in the trunk compartment. Remove any covers or panels that may obstruct access to the battery. Ensure the ignition is off and disconnect the negative terminal first, followed by the positive terminal when working on the battery. Always consult your owner's manual for specific instructions related to your MR2 model.

Why won't your Toyota MR2 windshield wipers turn off?

If your Toyota MR2 windshield wipers won't turn off, it could be due to a faulty wiper switch, a malfunctioning relay, or a stuck wiper motor. Sometimes, a short circuit or a problem in the wiring can also cause this issue. Checking the wiper switch and relay, as well as inspecting the wiring for damage, can help diagnose the problem. If these components are functioning properly, the wiper motor itself may need to be replaced.

Change speaker on door mr2 spyder?

To change the speaker on a Toyota MR2 Spyder, first, remove the door panel by unscrewing any visible screws and carefully prying off clips. Disconnect the wiring harness from the old speaker, then unscrew and remove the speaker itself. Install the new speaker by reversing the process: secure it in place, reconnect the wiring, and reattach the door panel. Ensure everything is properly secured before testing the new speaker.

What is the size of an mr2 bonnet?

The size of an MR2 bonnet (or hood) can vary slightly depending on the specific model year and generation of the Toyota MR2. Generally, for the second generation (AW11) and third generation (SW20), the bonnet dimensions are approximately 1.2 meters in length and 1 meter in width. However, for precise measurements, it's best to refer to the specific vehicle's service manual or consult a manufacturer’s specifications.

How do you replace drive belt 2000 MR2?

To replace the drive belt on a 2000 MR2, first, disconnect the negative battery terminal for safety. Remove the engine cover and locate the drive belt; then, use a wrench to loosen the tensioner pulley, allowing you to slip the old belt off. Install the new belt by routing it according to the diagram usually found on the engine cover, then re-tension the pulley before reassembling the engine cover and reconnecting the battery. Always check the belt's alignment and tension after installation.

Installing new shifter boot retaining ring?

To install a new shifter boot retaining ring, first, ensure the shifter boot is properly positioned around the shifter itself. Gently compress the boot and align the retaining ring with the groove on the shifter housing. Carefully push the ring into place, ensuring it snaps securely to hold the boot in position. Finally, check for any gaps or looseness to confirm a proper fit.

How do you fit head gasket on 2001 mr2 roadster?

To fit a head gasket on a 2001 MR2 Roadster, first ensure the engine is cool and disconnect the battery. Remove the intake and exhaust manifolds, and unbolt the cylinder head carefully, taking note of the order of bolts. Clean the surfaces thoroughly, then place the new head gasket on the engine block, aligning it correctly with the dowel pins. Finally, reattach the cylinder head, torque the head bolts to the specified settings in the correct sequence, and reassemble the rest of the components.

What make cars alloy wheel would fit on a mk3 mr2?

When selecting alloy wheels for a Mk3 MR2, you should look for wheels with a bolt pattern of 4x100 mm and an offset typically ranging from +35 to +45 mm. The diameter is usually 15 to 17 inches, with a width of 6.5 to 8 inches being suitable. It's essential to ensure that the wheels are compatible with the vehicle's brake components and suspension setup for optimal performance and aesthetics. Always confirm fitment with a reputable wheel retailer or manufacturer.

Were is the fuel pump fuse in a 1988 mr2?

In a 1988 Toyota MR2, the fuel pump fuse is typically located in the fuse box under the dashboard on the driver's side. Look for a fuse labeled "Fuel Pump" or "EFI" (Electronic Fuel Injection). Refer to the owner's manual for specific fuse location diagrams and ratings for accurate identification. Always disconnect the battery before checking or replacing fuses.

Which cylinder is number 1 on a Toyota MR2 mk111?

On a Toyota MR2 Mk3, also known as the MR2 Spyder, cylinder number 1 is located at the front of the engine, closest to the timing belt. The engine is a 1.8-liter inline-four, and the cylinders are numbered sequentially from the front to the rear, with cylinder 1 being at the front left when facing the engine from the passenger side.

What is the oil type for mr2 1989?

The 1989 Toyota MR2 typically requires 10W-30 or 10W-40 motor oil, depending on the climate and driving conditions. It's important to check the owner's manual for specific recommendations, as well as for any updates based on engine modifications or specific usage. Always ensure to use oil that meets API (American Petroleum Institute) standards for optimal performance.

Where is the battery in the Toyota MR2?

In the Toyota MR2, the battery is located in the front trunk compartment, which is accessible by opening the front hood. This design is part of the MR2's mid-engine layout, allowing for better weight distribution. To access the battery, you may need to remove any covers or panels that are in the way.

How do you install a boost gauge?

To install a boost gauge, first, select a suitable location on your dashboard or A-pillar for mounting. Next, run a vacuum line from the intake manifold to the gauge, ensuring it’s secured and free from leaks. Connect the electrical wiring if your gauge is electronic, then attach the gauge to the mounting location. Finally, double-check all connections, start the vehicle, and verify the gauge functions correctly.

How do you change the light bulb behind the speedo on a 1992 Toyota MR2?

To change the light bulb behind the speedometer on a 1992 Toyota MR2, first, disconnect the negative battery terminal for safety. Remove the screws holding the instrument cluster in place and carefully pull it out. Locate the bulb holder at the back of the speedometer, twist it counterclockwise to remove it, and replace the old bulb with a new one. Finally, reassemble the cluster and reconnect the battery.

How do you remove water pump 1985 mr2?

To remove the water pump from a 1985 MR2, start by disconnecting the negative battery terminal and draining the coolant. Then, remove the serpentine belt and any associated components obstructing access to the water pump, such as the timing cover and the alternator. Unbolt the water pump from the engine block, carefully prying it loose if necessary. Finally, clean the mating surfaces and install the new pump with a fresh gasket before reassembling everything in reverse order.

How do you bleed the clutch on a 1985 Toyota MR2?

To bleed the clutch on a 1985 Toyota MR2, start by locating the clutch slave cylinder, which is typically mounted on the transmission. Connect a clear plastic hose to the bleeder valve on the slave cylinder and place the other end in a container to catch the fluid. Have a helper pump the clutch pedal several times, then hold it down while you open the bleeder valve to release air and fluid; close the valve before your helper releases the pedal. Repeat this process until no more air bubbles appear in the fluid, ensuring the reservoir is topped off with fresh brake fluid throughout.

How do you replace timing belt on a 93 Toyota MR2?

To replace the timing belt on a 1993 Toyota MR2, first disconnect the battery and remove the engine cover for access. Then, drain the coolant and remove the necessary components such as the alternator, water pump, and timing belt covers. Align the timing marks on the crankshaft and camshaft, remove the old timing belt, and install the new one, ensuring proper tension. Finally, reassemble all components, refill coolant, and reconnect the battery.

What are the torque specifications for a 1985 Toyota MR 2?

The torque specifications for a 1985 Toyota MR2 vary depending on the specific component being tightened. For example, the cylinder head bolts typically require a torque of around 50 ft-lbs (68 Nm) in a specific sequence. Additionally, it’s essential to refer to the vehicle’s service manual for precise torque values for other components such as the connecting rods, main bearings, and wheel lug nuts. Always ensure to follow the manufacturer's guidelines for the most accurate information.

What is the fuel tank capacity of a 1987 Toyota MR2?

The fuel tank capacity of a 1987 Toyota MR2 is approximately 11.9 gallons (45 liters). This compact sports car was designed for efficient performance, and its fuel tank size complements its lightweight build and handling characteristics.

What is the firing order for a 1985 Toyota MR2 mk1 1600 twin cam?

The firing order for a 1985 Toyota MR2 MK1 with a 1600 twin cam engine is 1-3-4-2. This means that the cylinders fire in that specific sequence, which is essential for the engine's proper operation. The cylinder numbering starts from the front of the engine, with cylinder 1 being the frontmost.

Where is the starter on a 2003 Toyota MR2 Spyder?

On a 2003 Toyota MR2 Spyder, the starter is located on the driver's side of the engine bay, near the rear of the vehicle. Specifically, it is mounted to the transmission bellhousing, making it somewhat accessible from underneath the car. To reach it, you may need to remove some components or panels for better access.

Toyota MR2 does not start when hot?

If a Toyota MR2 does not start when hot, it may be due to a failing crankshaft position sensor or ignition coil, both of which can malfunction at elevated temperatures. Another possibility is vapor lock, where fuel vaporizes in the fuel line, preventing proper fuel delivery. Additionally, issues with the fuel pump, relay, or electrical connections can also contribute to this problem. Checking these components can help identify the root cause.

Can a 1993 mr2 mk2 be remapped?

Yes, a 1993 MR2 MK2 can be remapped, but the process can be more complex than with modern vehicles. The car's ECU (engine control unit) may need to be replaced or modified to allow for tuning, as many older models lack the technology for easy remapping. Additionally, performance gains may be limited by the car's engine and components, so it's essential to consider supporting modifications for optimal results. Always consult with a professional tuner with experience in older vehicles for the best approach.

Which Toyota engine is compatible with the 4jx1 engine?

The 4JX1 engine, a 3.0-liter diesel engine often found in Isuzu vehicles, does not have a direct Toyota engine equivalent. However, if you're looking for a Toyota engine that can be compatible in terms of dimensions or performance, the Toyota 1KZ-TE (3.0-liter turbo diesel) might be considered due to its similar displacement and diesel characteristics, although modifications would likely be necessary for a proper fit. Always consult a specialist for compatibility and installation advice.