Toyota

The 2012 Toyota Highlander is equipped with a timing chain, not a timing belt. Timing chains are generally more durable and require less maintenance compared to timing belts, which typically need to be replaced at specific intervals. As a result, the timing chain in the Highlander is designed to last the lifetime of the engine under normal driving conditions.

On a 2010 Toyota pickup, the oil filter is located on the underside of the engine, typically near the oil pan. It is positioned towards the front of the engine, making it accessible from below the vehicle. You may need to use a wrench or oil filter socket to remove it during an oil change. Always ensure to safely elevate the vehicle if necessary and allow the engine to cool before attempting to access the oil filter.

The transmission from a Toyota Supra is not a direct fit for a 1993 Lexus SC400, as they are designed for different engine and drivetrain configurations. The SC400 uses a 4.0L V8 engine paired with a specific transmission that differs from the Supra's inline-six options. While some modifications might allow for compatibility, it would require significant alterations to the mounting points, driveshaft, and possibly the ECU. It's advisable to consult with a specialist or perform detailed research before considering such a swap.

If the bonnet release cable is broken on a Yaris, you can try accessing the latch directly. Use a flathead screwdriver or a similar tool to pry open the grille or the area around the latch, which is typically located near the center. Alternatively, you can reach under the car if there’s enough space and manually pull the latch mechanism. If these methods fail, it may be necessary to consult a professional mechanic for assistance.

To replace the head gasket on a 1995 4-cylinder Toyota pickup, first disconnect the battery and drain the coolant. Remove the intake and exhaust manifolds, timing belt, and any accessories obstructing access to the cylinder head. Carefully unbolt the cylinder head and lift it off, then clean the mating surfaces thoroughly. Install the new head gasket, reassemble the components in reverse order, and refill the coolant before starting the engine.

The fuel capacity of the 1988 Toyota 4x4 pickup is approximately 18.5 gallons. This capacity allows for a decent range, making it suitable for both on-road and off-road driving. Depending on the engine and configuration, the fuel efficiency may vary, impacting overall range.

The main journal diameter of the Toyota 22RE crankshaft is typically 2.362 inches (60 mm). This measurement is crucial for ensuring proper fitment and function within the engine's main bearings. Always refer to a service manual for specific details and tolerances when working on this engine.

The girls in the Toyota Australia commercial are typically portrayed by various actresses or models, depending on the specific ad campaign. The commercials often feature relatable characters who embody themes of adventure, family, and the excitement of driving a Toyota vehicle. For the most accurate information regarding a specific ad, it's best to check the credits or official Toyota Australia sources, as casting can vary between commercials.

The introduction and relaunch of the Toyota Prius were significantly influenced by several macroenvironmental factors. Demographically, increasing environmental awareness among younger consumers drove demand for eco-friendly vehicles. Economically, rising fuel prices heightened the appeal of fuel-efficient cars, while technological advancements enabled better hybrid systems. Politically, government incentives for electric and hybrid vehicles supported its market entry, and culturally, a growing emphasis on sustainability aligned with the Prius's branding. Overall, these factors contributed to the Prius's success as a symbol of environmental responsibility in the automotive industry.

The song in the Toyota commercial for the 2018 Paralympics is performed by the artist Sia. The track featured in the ad is her song "Never Give Up," which emphasizes themes of resilience and determination. The commercial highlights the inspiring stories of athletes and their journeys, aligning with the spirit of the Paralympic Games.

The power door lock relay on a 1996 Toyota Corolla is typically located under the dashboard on the driver's side. It can be found near the fuse box or behind the panel where the steering column is. To access it, you may need to remove some lower dash panels. Always refer to a repair manual for specific details and diagrams for your model.

To replace the throw-out bearing in a 1986 Toyota 22R pickup 4x4, first, disconnect the battery and remove the transmission by unbolting it from the engine and supporting it with a transmission jack. After removing the clutch assembly, take out the old throw-out bearing from the clutch fork. Install the new throw-out bearing onto the fork, reassemble the clutch and transmission, and finally reconnect the battery and test the clutch operation. Always refer to a service manual for specific torque specs and detailed steps.

Yes, the Malfunction Indicator Light (MIL) may remain illuminated on a Toyota even after replacing the sensors if the new sensors have not successfully transmitted data to the Engine Control Unit (ECU). This could indicate that there is still a communication issue or that the ECU is not receiving the correct signals. It’s important to check for any additional fault codes and ensure that the sensors are properly connected and functioning. A diagnostic scan may be necessary to resolve the issue.

The 2001 Toyota Sienna with a V6 engine features an interference engine design. This means that if the timing belt were to fail, the pistons could collide with the valves, potentially causing significant engine damage. It's important to maintain the timing belt according to the manufacturer's recommendations to avoid such issues.

The torque specifications for the lug nuts on a 2012 Toyota Sienna are typically 76 lb-ft (102 Nm). It's always best to double-check the owner's manual or consult a professional for the most accurate information. Additionally, it’s advisable to torque the lug nuts in a crisscross pattern to ensure even distribution.

The fuel consumption of a Toyota Corolla Spacio typically ranges from 8 to 12 kilometers per liter, depending on the engine size, driving conditions, and maintenance. On average, you can expect around 10 km/L for a mixed driving scenario. For more precise figures, it's best to refer to the specific model year and engine type.

Toyota began using timing chains in some of its engines in the late 1980s. While specific models may have adopted this technology at different times, the transition from timing belts to chains became more prominent in the 1990s. Timing chains are generally known for their durability and longevity compared to timing belts.

To check if your thermo fan is working on a 1989 Hilux Surf, start the engine and let it reach operating temperature. Feel the radiator and the hoses; if they are hot and the fan is not running, the thermo fan may not be functioning. Additionally, you can listen for the fan operation when the engine temperature rises, or manually trigger it by connecting the fan to a power source to see if it spins. If it's not working, it may be time to check the wiring, relay, or replace the fan itself.

The first Toyota Camry rolled off the assembly line in Georgetown, Kentucky, on May 21, 1988. This facility marked Toyota's first manufacturing plant in the United States, playing a crucial role in the company's expansion and commitment to the American market. The Georgetown plant has since become one of Toyota's largest production facilities.

The front brake rotor size for a 2002 Toyota 4Runner Limited with a 3.4-liter engine is typically 12.0 inches (or 305 mm) in diameter. It's important to verify the specifications based on the specific model and any modifications that may have been made. Always consult the owner's manual or a reliable parts source for the most accurate information.

The Toyota Hilux HL2 and D4D refer to different aspects of the vehicle's specifications. The HL2 is typically a trim level that indicates features and equipment, while D4D refers to the 2.5-liter and 3.0-liter diesel engine technology used in some Hilux models, known for its efficiency and performance. Essentially, HL2 focuses on the vehicle's features, whereas D4D highlights the engine type. Thus, choosing between them involves considering both the trim level and engine performance.

The timing position for a 1997 Toyota 1.6 engine typically refers to the alignment of the camshaft and crankshaft during the engine's timing setup. For the 1.6L engine, the timing marks are usually aligned at TDC (Top Dead Center) on the crankshaft. The specific timing degrees for ignition advance can vary, but it generally falls around 10-15 degrees BTDC (Before Top Dead Center) when set at idle. Always refer to the vehicle's service manual for precise specifications and adjustments.

The ignition timing for a 1987 Toyota pickup typically ranges from 5 to 10 degrees before top dead center (BTDC) at idle, depending on the specific engine and configuration. It's important to refer to the vehicle's service manual for the precise timing specifications and any adjustments based on factors like altitude or modifications. Proper ignition timing is crucial for optimal engine performance and fuel efficiency. Always ensure that the timing is set according to the manufacturer's recommendations.

To replace the air conditioning panel bulbs in a 1991 Toyota pickup truck, first, ensure the ignition is off and disconnect the battery for safety. Remove the dashboard panel by unscrewing any screws and gently prying it away to access the air conditioning control unit. Locate the burnt-out bulbs, unscrew or pull them out, and replace them with new ones of the same type. Finally, reassemble the dashboard panel and reconnect the battery.

To reset the maintenance light on a 2008 Toyota Tacoma, first turn the ignition to the "ON" position without starting the engine. Press the gas pedal three times within five seconds, then turn the ignition off. When you turn the ignition back on, the maintenance light should be reset. If it doesn't turn off, repeat the process.