answersLogoWhite

0

Acura Integra

Also known as the Honda Integra, Acura Integra is a compact sport coupe manufactured by Honda from 1985 - 2007. Integra is a 2-door front wheel drive vehicle with 4-seating capacity. A 4-door edition of the vehicle is also available.

1,512 Questions

Where is the light relay box located in a 1990 Acura Integra?

The light relay box in a 1990 Acura Integra is typically located under the dashboard on the driver's side. You may need to remove the lower dash panel to access it. The relay box is usually mounted near the fuse box, making it a bit easier to find. Always refer to the vehicle's service manual for specific details and diagrams.

Where is the AC pressure switch on a 1997 Integra LS?

On a 1997 Acura Integra LS, the AC pressure switch is typically located on the high-pressure side of the air conditioning system. You can find it on the aluminum line that runs from the compressor to the condenser, near the front of the engine bay. It usually has a two-wire connector and may be identifiable by a small cylindrical shape. Always ensure the engine is off and the system is depressurized before attempting any inspections or repairs.

Where is an OBD1 plug to trouble shoot a 93 Acura Integra?

The OBD1 plug for a 1993 Acura Integra is typically located under the dashboard, near the driver's side. You can find it near the steering column, often attached to the lower part of the dashboard. Look for a rectangular connector with multiple pins, usually covered by a plastic cover. This is where you can connect an OBD1 scanner or jumper wire to troubleshoot the vehicle.

Where is the iat sensor on an 99 Acura Integra ls?

The intake air temperature (IAT) sensor on a 1999 Acura Integra LS is located in the intake manifold, specifically on the intake air duct, near the throttle body. It is typically a small cylindrical or rectangular component that is plugged into the air intake system. To access it, you may need to remove the air intake hose or duct. Always ensure the engine is cool and disconnected from the battery before attempting to locate or replace the sensor.

How do you set the timing on a 1999 Acura integra?

To set the timing on a 1999 Acura Integra, first ensure the engine is at TDC (top dead center) on the compression stroke for cylinder one. Then, locate the timing marks on the crankshaft pulley and the timing cover; align these marks to 0° BTDC. Adjust the distributor to align the rotor with the designated timing mark, and secure it. Finally, check the timing with a timing light to ensure it is within the specified range.

What type of clutch do you use for a ls vtec b18?

For an LS VTEC B18 setup, a good choice is a performance-oriented clutch that can handle the increased power and RPMs. A heavy-duty organic or ceramic clutch is often recommended, as it provides better grip and durability. Brands like Exedy, ACT, or Clutch Masters offer suitable options that can handle the demands of a modified LS VTEC engine while ensuring smooth engagement. Always consider your specific power goals and driving style when selecting a clutch.

How do you change the brake pads on a 1996 Acura Integra?

To change the brake pads on a 1996 Acura Integra, first lift the car and remove the wheel. Then, unbolt the caliper using a socket wrench, slide it off, and secure it to avoid straining the brake line. Remove the old pads, replace them with new ones, and reassemble the caliper. Finally, ensure everything is tightened properly, and repeat for the other side if necessary.

Where is the fuse for alternator in 91 Acura Integra?

In a 1991 Acura Integra, the fuse for the alternator is typically located in the under-hood fuse box. You can find it near the battery, along with other fuses. Check the fuse box cover for a diagram that indicates the specific fuse for the alternator, often labeled as "ALT" or "Alternator." If the fuse is blown, it will need to be replaced to restore proper charging.

What is the firing order for 1988 acura intregra ls?

The firing order for the 1988 Acura Integra LS, which is equipped with a 1.8L 4-cylinder engine, is 1-3-4-2. This means that cylinder number 1 fires first, followed by cylinder 3, then 4, and finally 2. Proper understanding of the firing order is essential for engine timing and performance.

How do you check firing order for 95 Acura Integra?

To check the firing order for a 1995 Acura Integra, refer to the vehicle's service manual or the information typically found on the underside of the hood. The firing order for this model is 1-3-4-2. You can also identify the cylinder numbers: cylinder 1 is located at the front of the engine on the driver's side, followed by 3, 4, and 2 in order. Ensure to follow this sequence when connecting spark plug wires or during ignition troubleshooting.

What size motor come in an 1989 integra?

The 1989 Acura Integra typically came with a 1.6-liter inline-four engine, known as the B16A, which produced around 108 horsepower. Some models may also feature a different engine configuration, but the B16A is the most common for that year. This engine is part of Acura's first-generation Integra lineup, showcasing a balance of performance and fuel efficiency.

How do you adjust headlights in 1989 Acura Integra?

To adjust the headlights on a 1989 Acura Integra, first park the vehicle on a level surface about 25 feet from a wall. Turn on the headlights and use masking tape to mark the center of the light beams on the wall. Locate the vertical and horizontal adjustment screws, typically found on the headlight assembly, and turn them to align the beams with the tape markings. Make small adjustments and check the alignment until the headlights provide optimal visibility without blinding oncoming drivers.

How much does a 1988 Nissan 300zx cost?

The cost of a 1988 Nissan 300ZX can vary significantly based on factors such as condition, mileage, and modifications. On average, prices typically range from $5,000 to $15,000, with well-maintained or low-mileage examples potentially fetching higher amounts. Collectors and enthusiasts may pay more for models in excellent condition or with special features. Always check current listings for the most accurate pricing.

Where is the VTEC oil switch located on a 1998 Acura 2.3CL located?

The VTEC oil pressure switch on a 1998 Acura 2.3CL is typically located on the engine block, near the VTEC solenoid. It is usually positioned on the driver's side, near the rear of the engine, and can be accessed from the top or the side of the engine bay. To locate it more easily, you may need to remove any obstructing components. Make sure to consult a service manual for precise details and diagrams.

What is the lugnut torque for a 1998 Acura Integra?

The recommended lug nut torque for a 1998 Acura Integra is typically around 80 lb-ft (108 Nm). It's important to ensure that the lug nuts are tightened in a crisscross pattern to achieve even distribution of pressure. Always refer to the owner's manual or a repair guide for specific information and any updates regarding your vehicle.

How do you change the Alternator in a 88 Acura Integra LS Hatchback Manual Transmission?

To change the alternator in a 1988 Acura Integra LS, first disconnect the negative battery terminal to ensure safety. Remove the drive belt by loosening the tensioner and then unbolting the alternator from its bracket. Disconnect the electrical connections from the alternator, and then remove the bolts securing it to the engine. Install the new alternator by reversing the disassembly steps, ensuring all connections are secure before reattaching the battery.

Why is brake light on in 2000 Acura Integra?

The brake light on a 2000 Acura Integra may be illuminated due to several reasons, including a malfunctioning brake light switch, low brake fluid levels, or a blown fuse. Additionally, it could indicate an issue with the anti-lock braking system (ABS) or worn brake pads. It's important to inspect these components to diagnose the exact cause and ensure safe operation of the vehicle.

What year and model Honda did the b18 and b16 vtec come in?

The B18 and B16 VTEC engines were introduced in the early 1990s. The B16A first appeared in the 1991 Honda Civic Si and the 1992 Honda CRX Si. The B18C, which is part of the B-series family, was most notably found in the 1994-2001 Honda Integra, particularly in the Integra GS-R models.

What is 2001 acura integra spark plug gap?

The spark plug gap for a 2001 Acura Integra typically falls between 0.040 to 0.044 inches (1.0 to 1.1 mm). It's important to check the owner's manual or verify with the manufacturer for the exact specifications, as they can vary based on the engine type and any modifications. Proper gap settings ensure optimal engine performance and fuel efficiency.

Where is the Fuel Pump at on a 1987 Acura Integra?

On a 1987 Acura Integra, the fuel pump is located inside the fuel tank. To access it, you'll typically need to remove the rear seat cushion and the access panel, or alternatively, drop the fuel tank itself. It's important to ensure the fuel system is depressurized before attempting any repairs or replacements. Remember to disconnect the battery to avoid any electrical issues while working on the pump.

How do you put more transmission fluid in a 94 acura manual integra?

To add transmission fluid to a 1994 Acura Manual Integra, first locate the transmission fluid fill plug, which is typically found on the side of the transmission case. Remove the fill plug using the appropriate tool, then use a funnel or a fluid pump to add the recommended type of manual transmission fluid until it reaches the bottom of the fill hole. After adding the fluid, securely replace the fill plug and check for leaks. Always consult your owner's manual for specific fluid types and capacities.

How do you change and what tool you use to change out the temp sensor on a 95 Acura integra?

To change the temperature sensor on a 1995 Acura Integra, first, locate the sensor on the engine, typically near the thermostat housing. Disconnect the negative battery terminal, then unplug the electrical connector from the sensor. Use a socket or wrench to remove the old sensor and install the new one, ensuring it is properly seated. Reconnect the electrical connector and the battery terminal, and check for leaks before starting the engine.

Do you have images of thermostat replacement on a 1993 acura integra?

I don't have the ability to provide images, but you can find diagrams and step-by-step guides for replacing the thermostat on a 1993 Acura Integra in online forums, repair manuals, or video tutorials. These resources typically include detailed instructions and visuals to assist you with the replacement process. Consider checking platforms like YouTube or automotive repair websites for helpful content.

How much hp does a b18c1 have?

The B18C1 engine, part of Honda's B-series, produces approximately 170 horsepower (hp) at 7,600 RPM and 128 lb-ft of torque at 6,800 RPM. This engine is commonly found in the 1994-2001 Acura Integra GS-R model. Its high-revving nature and VTEC technology contribute to its performance characteristics.

Where is the PVC located on a 97 Acura Integra gsr?

On a 1997 Acura Integra GSR, the Positive Crankcase Ventilation (PVC) valve is located on the engine's valve cover. Specifically, it is usually found near the rear of the valve cover, connected to a rubber hose that leads to the intake manifold. To access it, you may need to remove any obstructions, such as the air intake duct or engine cover.