0
Acura CL
Acura CL is a car model produced by Honda’s Acura brand from 1997 to 1999 and from 2001 to 2003. The CL was the first vehicle from the Acura series to be built in the US.
467 Questions
How do you change the rotors on a 2003 Acura CL?
Take off the tire (obvious), remove the two caliper bolts (12mm), and move the caliper off of the brake assembly: the brake line is short, so you have to have something to set the caliper on, or fashion a hook to hang it from if you don't want to disconnect the brake line. I used a metal hanger as a hook, and hung the caliper by the upper mounting hole suspended from the upper control arm. Next, you remove the two brake pad mount bolts (14mm) and remove the entire assembly with the brake pads on it. The rotor is now completely exposed and is ready for removal. There are two Phillips screws holding in onto the hub, and possibly a few years of road gunk too. My screws were rusted and stuck in place. I bought a tool at Sears that is a hammer-actuated hand impact wrench. It retails for $30. You put the screw adapter on and line it up with the screw, then start whacking it with a hammer. Each whack puts a ton of torque on the screw and will rotate it approximately 20 degrees. That did the trick with my stuck and partially stripped screws, but I'll bet a full out impact wrench with screw tip will work too. Once both screws are out, the rotor is technically unsecured, but again may be stuck from years of gunk as mine were. There are two other holes in the rotor hat for removal screws. By threading screws into those holes, you put pressure on the hub, and force the rotor off. I found that the screws are approximately 1/2 inch diameter. I had some old HW laying around, and found two conduit clamps for industrial wiring jobs that had mounting screws with square heads that fit perfectly. The square heads were slightly difficult to work with, but a 8mm or 9mm open-ended box wrench fit perfectly, and after about 3-4 turns apiece, the rotors popped right off. Install your new rotor, put the brake pad assembly back on and reinstall the caliper. One additional note: the screws through the rotors are unnecessary. The caliper holds it securely in place, and even if it didn't, the pressure of the wheel will hold it snug as well, so do yourself a favor, don't reinstall the two screws into your new rotors. I used mine to hold it in place while I reinstalled the calipers and pads, but then removed them and tossed them.
Why won't my car engine start 1997 Acura CL 3.0?
Is there any gasoline in your tank. Put some in there!
How do you replace the hid bulbs on a 2001 Acura CL?
I had to pull off the front bumper to replace the ballast and high and low beam bulbs. that's the only way that I know. I had to do this 2 times when the other bulb went out.If the bulb you replace does not work then it might be the ballast.
What causes the air conditioner to stop blowing cold air in a 1997 Acura 2.2L?
Blown fuse? Freon leak? Suggest you take it and have it checked to be sure.
Locate the fuel filter on Acura CL 2.2?
The fuel filter on a Acura Cl is located in the engine bay. The part itself is bolted onto the firewall towards the rear of the engine.
How do you get the check engine light off on a 97 acura?
i just made mine go off by taken off the pos battery cable for 15 min but you better know the code for the radio if you do that,my code was on the side of the glove box.
1999 Acura 2.3 cl that shifts hard only from 1st to 2nd Does transmission need an adjustment?
Probably needs pressure switches, or needs to have the solenoid screens cleaned out. Use and OBD reader to see what transmission codes are in the computer to determine which switches/solenoids need attention. Don't let this go too long or then you'll burn out the clutch packs and have much more expenseive repairs.
Why would the battery indicator light come on in a 1998 Acura CL?
Probably either the battery, alternator, or related wiring is at fault. Have the electrical charging system checked. Many mechanical shops and some auto parts stores will perform this test for free, especially if they think your likely to purchase parts or repairs from them. Don't be afraid to get a second opinion from another source, however, especially if you're told it's going to be an expensive fix.
How do you change timing belt on a 2001 Acura CL type s?
I'm pretty sure it has a timing chain, like the rsx typeS. Could be wrong, but I think I'm more right then wrong.
How do you change the headlight bulb on a 1997 Acura CL 3.0 liter?
You first need to remove the black plastic covering by unscrewing the big plastic bolts. They just unscrew so don't try to remove. Look down where your headlights are and there should be plastic clips (mine are blue and white) you need to push on the lever on the bottom of the plastic clip at the same time as you are pushing down. ( I cheat and use tools for additional muscles, a flat screwdriver works best) It should come off disconnecting the power from your headlights. There should be 3 spots where lights can go, hi-beams, headlights, and turn signals....determine which one needs replacing. Turn the back of the light clockways and it should pop out carefully. Replace and turn counterclock ways until light is locked back into place. Replace clips and black plastic cover.
Srs light is on 1999 Acura CL?
Supplimental Restraint System -- something is wrong with your airbag system(s).
How do you change a serpentine belt on a 97 Acura CL 3.0?
Find the tensioner pulley. Use a straight wrench (I believe a 14mm) and turn the tensioner pulley bolt (the one in the middle of the pulley) counter clockwise (you may need an extension Pipe). This will release tension on the belt then slide the belt off. The tensioner pulley bolt is a reverse thread so it will not come loose when attempting to turn it counter clockwise. Slide the new belt on from the bottom up then turn the tensioner pulley counter clockwise (releasing tension) with one hand while sliding the belt over the alternator pulley (a long screwdriver wedged against the side wall can help get the belt onto the pulley) then allow the tensioner pulley to return to its normal position.
Where is the blower motor on a 2003 Acura CL type s?
The HVAC blower motor for a 2003 Acura 3.2 CL Type S can be found under the right side of the dash board. It is directly to the left of the passenger side kick panel.
How do you replace the ballast on a 2003 Acura CL 3.2?
First, disconnect the battery as a safety precaution. One of these HID ballasts can cause electric shock or electrocution. Second, remove the front bumper cover. Then remove the headlight assembly for the ballast which needs replacement. The ballast can be found on the bottom of the headlight assembly. Replace the ballast and reinstall all removed parts. Reconnect the battery and confirm the repair.
How do you fix error code Acura CL CD player?
You can disconnect the battery. Then connect it back, use your secret code and it should work again.
There are 3 step to repair CD player error
If you got CD player error then there is a 94% chance that your computer has registry problems. To repair CD player error you need to follow the steps below:
* Step 1 - Download a Perfect Optimizer,install this error repair tool.
* Step 2 - Click the Repair All Button.It will scan you PC for Free.
* Step 3 - Then click the Repair All Button again and your done! It is very easy to repair CD player error.
How many quarts do you need for a 2003 Acura CL 3.2 type s?
how many quarts for a 2003 acura cl 3.2 type s how many quarts for a 2003 acura cl 3.2 type s
How do you change the spark plugs in a 2001 Acura CL?
The CL requires 6 spark plugs...I used the platinum bosch plugs which do not require to be gapped. The front three are pretty easy. The back three require you to use different lengh extensions for your socket wrench. Basically the process is the same, loosen the bolt which holds the plug cable, insert the spark plug socket and remove and replace one after another versus undoing everything at once. I think it took about 45 minutes from start to finish.
