0
Chevy Nova
The Nova was a compact car manufactured in five generations by General Motors. The first four generations were equipped with front-engine, rear-wheel drive (FR) layout, while the last one was available in a front-engine, front-wheel drive (FF) layout.
869 Questions
What kind of headers do you put on your 65 nova?
depends on the motor you have in it, I have a 400 Chevy in mine and I use the hooker fenderwell exit style, but summit and jegs as well as 2 or 3 other makers sell the under car exit for the early nova 1962-1967
Will a 1972 Chevy nova front end fit a 1974 Chevy nova?
I think that the 74 is wider, but I am not positive. However, your answer would actually be, yes. Any hot rodder, can make anything fit anything, at any given time. As for bolting right up, I don't think so. Modifications would be needed.
What is the transmission fluid capacity for a 1977 Chevy Nova straight 6?
For automatic trannies: TH200 = 4.5 qts TH350 = 10 qts.
What is Compression specs for 1974 nova 350?
Compression ratio on a 1974 Chevy 350 in a Nova was 8.5:1.
Where is the oil drain plug located on a 1977 Chevy Nova?
In the bottom of the oil pan, towards the rear of it.
Will the front of a 1970 nova fit a 1976 nova?
No. The subframes are not the same. The 68-74 had the steering behind the crossmember and 75 and up had it in front of the crossmember.
What front clips can be used on a 1963 Chevy Nova?
62, 3, and 4, other than some minor grill changes, are the same. 65, will work, however, there were major front end changes to the 65, so they do differ, noticably.
Will a edelbrock carburetor fit on a holly intake?
Yes it will just be sure you use the wright carb. base gasket.
How can you replace points on a 1977 nova?
A 1977 Nova should have electronic ignition and therefore wouldn't have points
You lost your build sheet for your 1968 Chevy SS Nova where can you call or write to get this?
Since it's a Chevy....good luck with that. Not trying to be a smart azz about it, but the only GM company I know that kept their records on the cars was Pontiac.
Can you replace a one barrel carburetor with a two barrel without replacing the manifold?
Companies like Transdapt make aluminum spacer-like adapters to mount a 2bbl carb on a 1bbl manifold . Not very efficient and they are application specific .
How do you adjust the PCV valves on a 2000 Acura Integra GSR?
You do not adjust PCV valves. You just replace them. Now if you are referring to the intake and exhaust valves, then you need to have this done by a professional. Severe engine damage can occur if this is not done correctly. Only a job for an expert.
Where do you take the oil pressure on a chev 350?
where the oil filter goes look above it,,, if car is dirty wash that area.... so look above filter there be a Allen bolt in it flushed with block.. undo with Allen ranch probly 9/16 or 7/16 or 1/2 i don't recall which one it is, then u put the oil pressure little bolt in it and there be a then that plugs in to it... so what i did is put in block snug and put other part on all the way then finish tight-ing to block and then put on oil pressure u well have to probly drill hole through dash first then go through there
What Tilt steering column fit 1970 nova?
70's nova's had a tilt wheel as an option so if you could find one that would be the best trick but you can get a custom steering column for it from ididot.com.
What is the bolt pattern for a 1970 nova?
1970 could have a 5 on 4.5 or a 5 on 4.75 bolt pattern measure from one cbolt enter to the next bolt center if distance 2 5/8 then 5 on 4.5 bolt pattern if distance 2 3/4 then 5 on 4.75 bolt pattern if distnace 3 then 5 on 5 bolt pattern if distance 3 1/4 then 5 on 5.5 bolt pattern hope this helps
