0
Chrysler Sebring
The Chrysler Sebring is a range of middle-sized cars manufactured by American carmaker Chrysler between 1995 and 2010. It is one of the few practically priced automobiles available in sedan and convertible body styles.
2,284 Questions
How do you check trouble codes on a 1997 Chrysler Sebring?
Either purchase an OBDII code reader from the auto parts store or use the three key-turn method.
If you turn the key three times without starting, and the last time you leave it in the acc on position, the engine light will flash, giving you the older more general codes. There are other questions on the board that have been answered to explain this method much better than I can.
With the OBDII code readers going for less than 60 dollars now, It may be a good investment to buy one for your car. It will definitely save you money if a repair shop tells you the "computer says its your fuel injectors" when the scan tool tells you that its something like an "egr leak"
Buy a new gas cap that will fix it
Is there a manual release for the fuel door in a 2009 Chrysler Sebring?
Isn't it the same as the 2008?
Simply push the door in to release it and again to close it....
Where is the brake light switch located on a 1998 Chrysler Sebring Convertible?
underneath the brake pedal
What type of oil should be used in a 2004 Chrysler sebring convertible?
5w30 but it depends on the size of your engine.
How do you replace lower ball joint on a Chrysler sebring?
Replacing the lower ball joint on a Chrysler Sebring is not the easiest thing to do. The best option for replacing it is to seek out a chrysler dealership or go to a professional mechanic that knows the specific car model and have done this type of work before.
Where is the reset button on a 1997 Chrysler sebring?
Chrysler does not use reset or inertia switches.
Where is the EGR valve on a 2001 3.0L V6 Chrysler Sebring?
Looking at the engine from the front/top it is in the center between the firewall and the rear of the engine near the throttle input. actually very east to replace. On coupe, it is NOT easy to replace. The entire intake manifold must be removed to gain access.
How do you get the air out of the cooling system of a 2004 Sebring?
There is a bleeder screw (it looks similar to the type you would see on a brake caliper) on top of the thermostat housing. This is on the passenger's side of the engine, right where the large radiator hose goes towards the firewall from the radiator. Opening this bleeder screw (ONLY WHEN THE ENGINE IS COLD) will allow trapped air to escape. Be sure to keep the coolant tank at the "cold full" mark while doing this. If the coolant tank runs dry, you likely will introduce more air into the system.
Where is the OBD connector for a 1998 Chrysler Sebring?
The 1998 Sebring OBD 2 port is under driver side dash next to center console
How do you fix code p1492 on 96 Chrysler Sebring?
P1492 Battery Temperature Sensor Voltage Too High
Test and/or replace the battery temp sensor. It is usually located under or near the battery.
How do you replace the oil pan gasket on a 2004 Chrysler Sebring convertible 2.7 liter engine?
1. Jack up your car and place it on jack stands.
2. Drain your oil (remove oil plug)
3. Remove your oil filter.
4. Remove the oil dipstick and tube ( one bolt #14 wrench size. front of engine).
5. Remove cross bracket ( four bolts #15 wrench size. attached to oil pan).
6. Remove two nuts from the front exhaust and use a bungee cord to hold it up.
7. Remove two nuts from the rear exhaust.
8. Remove the lower bolt from the A/C.
9. Remove the torque converter cover (next to the oil pan). (one #18 bolt, two #10 bolts, there is also a rubber gasket between the torque converter and the oil pan that needs to be removed.)
10. Remove the two bolts from the timing chain cover #10 wrench
11. Remove two nuts on the left of the oil pan and two nuts on the right. #10 wench)
12. Remove five bolts on the front and 5 bolts on the back of the oil pan. #13 wrench).
13. Remove oil pan and gasket.
14. Clean oil pan and check for cracks .replace if needed.
15. Clean oil pan surface thoroughly!
16. Clean engine surface thoroughly!
17. put RTV silicone sealant on the left and right sides of engine surface.
18. place new filter over the four small bolts...silicone should hold it in place.
19. place the oil pan over the top of the four bolts and place the nuts on But DO NOT Tighten!
20. hand tighten the ten bolts.
21. hand tighten the four nuts.
22. hand tighten the two bolts on the timing cover.
23. use a torque wrench to tighten to ten bolts.
24. use a torque wrench to tighten the four nuts.
25. use a torque wrench to tighten the two bolts.
26. tighten the bolt to the A/C.
27. Replace the Torque converter cover and rubber gasket.
28. Reattach the exhaust pipes. (Rear first, then front)
29. Reattach the cross bracket.
30. tighten the oil plug and replace oil filter.
31. Reattach the oil tube.
32. Replace oil.
33. Check for leaks.
34. lower the car off of the jack stands.
35. Take a shower.
36. Take a test drive!
What is the firing order of a 1999 Chrysler Sebring 2.5l v6?
The firing order is 1-2-3-4-5-6. The order of the wires on the cap is labeled on the cap.
How do I reset the engine light on a 2006 Chrysler sebring?
You use a scan tool after repairing the failure.
Will 22 inch rims fit on your 2004 Chrysler sebring?
I have the solution for you. For the 2004 Chrysler Sebring Coupe Limited 3.0 (That is the Sebring with the V6 Engine the 6G72) you have to go on eBay and order to pairs of WHEEL ADAPTERS SPACERS 5X114.3 CHRYSLER DODGE FORD 2".
Make sure that they are hub centric The 2004 Chrysler Sebring Coupe Limited's Suspension is designed only for 17" rims which suck. To bypass that the spacers will enable the wheels to "bow out" giving it an aggressive look. They will tuck under your wheel well but you will have a problem with rubbing. Also another problem that will arise is that you CANNOT have no more than you and a passenger in the vehicle because the car is designed to only hold a little over 830lbs inside the cab. So if that is your daily driver or family car you are screwed but if it's your toy car then you are fine. You must also make some modifications to the engine and transmission to handle the new allotted weight of the wheels and yourself. The Rims' size should be 22x8.5 and the tire size should be 235 30 R22 Z. You need Z rated tires for the highway (or Autobahn if you're in Europe). Do not be cheap. Trust me you will thank me later. If you want to modify it further take it to the body shop and remove about 2" off of the wheel wells/fenders to add to your over all turning radius. You do not need a lift kit and they will tuck just fine. Trust me.
-M.a.V.
How do you change the battery in a 1999 Chrysler Sebring?
I had to do this, the battery is located in the left wheel behind the wheel cover. I have also found that most places will do this with an extra fee.
If it is a convertible, it's easy.
The battery is under the left front fender.
Remove the negative battery cable.
Loosen the lugs nuts about 2 full turns (front left wheel).
Lift the left front corner, using an appropriate floor jack or bottle jack. The best place to lift is either the frame pad behind the front left wheel inside the body weld (see Owners Manual), or lift the A-arm directly, as far outboard as possible.
Remove the wheel.
The battery is under the front left fender. There are two nuts holding the battery bracket in place. Remove the two nuts.
Then remove the battery cables from the battery. Then slide the battery out.
Put the new one in, fasten the cables, install the bracket, put the wheel on, and hand tighten the nuts.
Let the car down, then finish tightening the lug nuts.
Attach the negative battery cable.
You're done.
It will take a couple days for the computer to "re-learn" the engine, so performance might be a little loose for a couple days or so.
ATF+4 Type 7176 is Mopar's current type of transmission fluid. So I think both of your options are the same.
ATF+4 Type 7176 is Mopar's current type of transmission fluid. So I think both of your options are the same.
What is the proper tire pressure for a Chrysler Sebring?
33PSI, but check the label on the driver door jamb to be sure.
Something is wrong. Take them apart and see what happened and why. Possibly one of the metal shims slipped out of place during the install. Don't keep driving knowing something isn't right with the brakes.
1998 Chrysler sebring jxi making noise when you shift into gear?
When a 1998 Chrysler Sebring makes noise while shifting the transmission should undergo a fluid change. Dirty fluid can cause hard shifting. The engine should also be given a diagnostics test to see if all the sensors are functioning correctly.
