Ford Fusion

Motorcraft ( FL - 910S ) engine oil filter for the 2.5 liter 4 cylinder , according to

the Owner Guide

I just completed by replacement this past weekend and it was much easier than I thought it would. First remove the door panel, there is a square head bolt in the hadn rest and one torx screw holding the handle cover on. There is also at least one torx screw holding the door panel on the edge. After the screws are removed gently pry the door panel off the door being carful not to break any of the plastic tabs. Once off remove the door handle and remove all of the bolts around the metal panel in the door. Now drill through the rivets holding the regulator to the metal panel, there are two large rivets and one small one. You will then be able to lossen the regulator from the window glass, unscrew the 3 screws fastening the regulator to the motor and remove the regulator. then install the new regulator to the window glass and reinstall the regulator to the motor. The 2 large rivets I replaced with 1/4 inch galvanized bolts with lockwashers and nuts, I used 1 inch longs ones. I replace the small rivet holdin the regulator to the motor with a similar sized rivet. Once the regulator is attached to the motor and panel you can reinstall the metal panel to the door with the bolts, reinstall the door handle and reinstall the plastic door panel to the door reinstalling the screws.

For a fist timer with my 2006 fusion it took about an hour.

If one of your indicators (front or rear) blinks too fast it normally means that the corrosponding bulb is burnt out.

i.e. if the left rear blinks too fast the left front is probably burn out or the terminals on the left front bulb are slightly corroded and not making proper contact.

4 cylinder takes 4 1/2 quarts including the filter. 6 cylinder takes 6 quarts including the filter.

#15 - 20 amp fuse - cigar lighter ( according to the 2006 Ford Fusion owners manual )

2010 FORD FUSION (EPA estimated miles per gallon)

2.3L Inline 4 Hybrid Engine ~ 43mpg city / 38mpg highway

2.3L Inline 4 Gas Engine ~ 25mpg city / 34mpg highway

3.0L Gasoline V-6 ~ 20mpg city / 25mpg highway

3.5L Gasoline V-6 ~ 20mpg city / 24mpg highway (Sport Models Only)

NOTE: Miles per gallon ratings may vary if the All-Wheel Drive system is equipped.

In the glove box.

The 2012 Ford Fusion is 15 ft. 10.6 in. (190.6 in.) long.

The Motorcraft OEM. it's a synthetic blend.

According to the 2012 Ford Fusion Owner Guide :

For the 2.5 liter four cylinder engine :

( Motorcraft FL-910S engine oil filter )

Boris Kodjoe is the black man in the new Ford commercials.

The 2012 Ford Fusion runs on regular unleaded.

It is an AC powered vehicle. It has an 88KW Magnet AC Synchronous Motor

I am no mechanic, however this is a 2 part fix. First the battery is shot, so replacing this is one part. The next is a little more complicated. You should take your vehicle to autozone or somwhere similar and get the alternator checked out. It sounds like this may need replacing as well. Like I said start with the battery, as this is the cheapest, but get the alternator checked out as well, or you would just waste the money on blowing another battery if the alternator is the problem. Best of luck!

Right now where i live in murrieta CA gas prices are at$4.24 by the gallon. Do the math if a car can hold 47mpg how many miles are you going to need and how many times will you need to fill up. it all depends on how much you drive to.

Check the Vehicle Emission Control Information ( VECI ) decal

located in the front of the engine compartment ( it will show what

type of spark plugs to use and the spark plug gap )

no i have an 08 fusion sel and it has an analog clock in the center of the main console above stereo

This is very easy to change, you don't need any mechanical experience.

1. You have to open up the access panel in the front wheelwell, turn the wheel all the way and unscrew the one screw holding it in.

2. Then use needlenose pliers to pinch the plastic clamps together holding the sidemarker in place, there is only one clamp holding each side marker. You can peek in from above with an open hood to grasp the clamps.

3. Pull the side marker out.

4. Twist the light and wiring out of the side marker.

5. Put the light in the new side marker, push the marker into position, close the access panel. Then do the other side.

The Ford Fusion has 2 axles.

No , the 2.3 liter and the 3.0 liter engines in a 2006 Ford Fusion have the

Coil On Plug ( C.O.P. ) ignition systems

To add Freon to a 2010 Ford Fusion, first ensure the vehicle is turned off and locate the low-pressure service port, usually found on the larger diameter AC line. Attach the refrigerant can to the service port using a suitable adapter, then start the engine and turn on the AC to the maximum setting. Slowly open the valve on the refrigerant can and monitor the pressure gauge until it reaches the recommended level. Be careful not to overfill, and always follow safety precautions.

The 2007 Ford Fusion has a drag coefficient of 0.33 Cd.

The 2009 Ford Fusion is 15 ft. 10.2 in. (190.2 in.) long.

The 2013 Ford Fusion has a 6-speed automatic.