0
Ford Laser
The Ford Laser is a small car marketed by Ford in Oceania, Asia, Africa, and parts of South America. It has always been available as a sedan, although wagon, convertible, and pickup versions have also been offered on various markets.
383 Questions
Where do you put the fluid for the gearbox of a Manual KN Ford Laser LXI Hatch?
On all the lasers iv'e worked on, you have to top the gearbox level up by removing the speedo out of the gearbox. There is one bolt that holds the speedo in, You will need a 10mm socket to undo it. pull the speedo out. I usually use a screwdriver to pry up on it. The level should be filled up approx. half way up the gear. It's a stupid way of doing it. But that's how you do it. It's weird though cos most laser gearboxs use automatic transmission fliud.
How do you remove rear brake drum on a ford ka?
Well, honey, to remove the rear brake drum on a Ford Ka, you'll need to first loosen the lug nuts, jack up the car, and remove the wheel. Then, you'll locate the retaining screws or clips holding the drum in place and remove them. Finally, give the drum a few good whacks with a rubber mallet to break it loose and slide it off. Voila, you've got that drum off faster than you can say "Golden Girls marathon."
Try your local library.
Where is the Vin on a ford laser 1987?
There should be little square metal plates pop rivetted to the fire wall inside the engine bay, one of them should say 'VIN' then have a number.
hope this helps!
On the SOHC 1.6 there are timing marks on the sprocket and rocker cover and on the block on the exhaust side about level with the top of the manifold.. I don't know if this helps. I hope so.
Your 1989 model Ford Laser engine is pinging how do you fix this problem?
All Ford Lasers of this year require Regular fuel except the GT-X which requires you use Premium fuel. If you are using the correct fuel then your engine may be out of time, which will cause it to ping. Have the timing checked by a professional. If it is not out of time and you are using the correct fuel then it more than likely has carbon buildup. Purchase a can of Seafoam Engine Treatment and follow the directions on the can to inject Seafoam into the intake to remove carbon deposits. You may have to treat it more than once. Also add a can to a full tank of fuel. You can purchase Seafoam at most auto and marine parts stores. I have used it many times to remove carbon deposits and it does work. If this does not solve your problem then make sure you do not have a vacuum leak. If not, then you may be forced to move up to a higher octane fuel. Pinging will eventually damage your engine so you must do whatever necessary to prevent it.
How do you change rear light bulbs on a Ford Laser 1.3 hatch 1994?
I have a 1990 laser and I think they should be the same. In the boot/trunk just behind where the lights are, there should be a removable cover which gives access to the back of the lights, disconnect the light that needs replacing and remove the bulb. For more information consult your car's owners manual it should have all the information in there.
Working model based on any principle of physics?
You can make foam balls on speaker output Model . This will be related to sound.
You can make a little tiny see-sawwith a movable pivot, and use it to illustrate the
three classes of levers, and to demonstrate how work energy is conserved in the
operation of levers.
How do you install rear speakers in a 1991 Ford Laser?
First you take out the old speakers if you have them.Then you put the speakers in the back because in the front there are too many wires.You plug it in and you are good to go.
Where is the engine number on a Ford Laser 1990 1.6 east west motor?
It is usually part of the VIN eg: 6FPAAA-UK4RLL11111, and the engine number being the latter part of the number showing on the plate circled with a box stamp.
Alternatively it located at the front of the engine block to the right, low down where the gear box meets the engine, horizontal to the left of where the gearbox mounts to the chassis, it is trickey to get to and you may need to clean that area of the block before it will be visible. and recommend using a torch.
Does a 1988 ford laser have a VIN?
All cars have a vin number. It should be located on one of the plates that are pop rivetted to the firewall in the engine bay.
,
First of all, it is important to know the definition of laser:
LASER - LIGHT AMPLIFICATION BY STIMULATED EMISSION OF RADIATION
A laser functions as an oscillator or a resonance of light (inside the laser device) in the sense that the radiation is produced by the power supply which cause an active lasing medium to emit electrons at a certain frequency (thereby giving a light). These electrons are emitted inside the device and reflected back and forth by a mirror numerous number of times. The in turn excite other electrons, thereby emitting photos (light) from the lasing medium. Therefore one action results in further action. Thus completing the definition - emission is for light in form photons due to the electrons which are a form of radiation and they are amplified inside. This produces a beam that is parralel in nature and is emitted out eventually through the small slit (source). By exciting electrons with different energies, you can emit light at different wavelengths, thereby different colours.
Hope this helps.
All the best,
How do you remove horn cover Ford Laser 1988?
The rubber cap has a lip that goes over a metal rim. Use a small screwdriver at the edge to lift and remove,,Chris
autozone.com Check out this site. Type in your vehicle info and follow the instuctions. Good luck.
What is the valve tappet clearance on Ford Laser year make 1983?
hey man. tappet clearances are almost always in the manual of any car..
dont have the manual anymore?
go to your local city library! they have car manuals from practically a-z!
INLET ...10 thou... EXHAUST ....12 thou HOT.
Where are the anchor points for baby capsule in a Ford Laser?
My 94 laser has an anchor near the latch for the hatch
