answersLogoWhite

0

Ford Mustang

The Ford Mustang is a famous compact car built by the Ford Motor Company. The first manufactured Ford Mustang, a white convertible with black interior, was launched on April 19, 1964.

1,730 Questions

What size gas tank in a 1989 Ford Mustang?

According to my Chilton's Auto Repair Manual :

A 1989 Ford Mustang has a ( 15.4 U.S. gallon gas tank )

What does the Mustang eat?

The Mustang will rapidly devour anything that burns rice, but also feeds on Camaros, Firebirds, Challengers, Trans-Ams, and Javelins to name a few. In fact, its appetite for the Camaro was so great that these were once thought to be extinct, however small numbers of these have recently been spotted in the wild. Come on people, obviously the person who asked this didn't mean a car! Mustang horses will eat the same as any other horse- grasses and grains and such- and in captivity it would eat grain and hay like any other horse, but in the wild it would eat grass, leaves, bushes and shrubs.

What do the codes mean for Ford Mustangs?

It depends on the year. Check out this link:

http://www.mustangdecoder.com/plates.html#1965

Your 2005 ford mustang hood wont pop the hood release is just pulling and not popping what do you do to open it?

My 1991 GMC Yukon dose the same and I cant figure it out but me being an Ase certified in NHRA top Fule drag racing I pull the hood latch and go to the hood and pull up it should just pop up.

How do you set timing on 1.8 92 escort gt?

You just turn the whole distributor loosen both bolts and turn slightly when the car is running.

What is overdrive on a Ford Mustang?

its acruising gear on all fords whether manual or auto so you save gas and your tranny goes into a higher gear, less torque on tranny

How do you remove the ignition cylinder on a Mustang?

get on the bottom of your car and push the ignition cylinder out

This works on '94's and newer...well, at least up to '04.

Step #1 is very important if you don't want your air bag to blow...

  1. Disconnect the neg. cable from the battery, disconnect the pos. cable from the battery, wait 2 minutes.
  2. Turn the ignition switch to RUN.
  3. Insert a 1/8 inch punch up through the little hole in the trim under the lock cylinder (you don't need to take any plastic off), hold the punch in while you pull out on the key. You should be holding the lock cylinder in your hand now.

Installation is almost the reverse (your battery is still disconnected, I hope):

  1. Push in the locking pin on the side of the new cylinder and turn the key so the cylinder is in the RUN position.
  2. Install the cylinder into the housing--fully seated and aligned with the interlocking washer.
  3. Turn the key to OFF. This lets the pin pop back out and lock the cylinder in place.
  4. Test the key by turning it from OFF to START. If that checks out, go to step 5 otherwise go back to 2.
  5. Reconnect the battery, Pos. first, then Neg.

What is a mustanger?

A "mustanger" is a person who owns or is a mustang enthusiast.

I waved to Jake at the auto-parts store since he was a fellow "mustanger", knowing he owns a 1993 gt.

a mustanger is also someone who kills mustangs

Should the sleeve where the front crank seal fits be removed before replacing it with an aftermarket crank seal on a ford mustang v6 engine?

Well there should not be a sleve in the crank snout where the seal lip rides. If there is one, then the crank has been reconnditioned/replaced, or there was damage to the snout, previously. I will recommend leaving the sleave, or replacing it with a new one if it has obtained rotational damage from the seal lip. This happens usually due to oil starvation at the lip ridding area or from a hardenned seal. The sleves may be purchased at your local autoparts and only serve to go over the damaged grove that the seal duged in. If the seal was not leaking and one is replacing the seal as maintenance or timing chain r&r. then leave the sleave in place other that that remove damaged sleve and replace with new one..Hope this helps.. Will..:)

What is the value of a Mustang by Guigiaro?

the "GIUGIARO" mustang is a concept model mustang only and is not a production car.. as you may be able to tell by the name the design was created by an Italian named Fabrizio Giugiaro and production models are never put up for sale unless somethin weird happens like the car goes missing.. most concepts are scrapped

What is the firing order for a 5.0L?

The 5.0 is 1-5-4-2-6-3-7-8 except for the 5.0 HO which is 1-3-7-2-6-5-4-8 Or: http://autorepair.about.com/od/enginefiringorders1/

Is a Ford Mustang faster than a dodge viper?

No. Factory equipped Mustangs cannot match the Viper's V-10 motor.

2009 Dodge Viper SRT-10 claimed top speed = 200 mph

2009 Ford Mustang GT V-8 claimed top speed = 145 mph

Keep in mind Dodge may have claimed a slightly higher top speed than actual to appeal to wealthy speed demons who can afford to insure such a car, while Ford may have claimed a lower than real life number to keep the Mustang affordable to insure.

Even with that taken into consideration a Viper would run down a factory built Mustang in short order. Even specialty built Mustangs like the Roush and Saleen models would have a hard time keeping up.

However the Mustang's lighter weight and handling will give it an edge in some aspects of driving and racing.

Which is faster a lancer evolution or a mustang?

The Mitsubishi Lancer Evo 2011 is better than a Ford Mustang GT 2011.

How do you you set timing on 2000 mustang gt?

The timing curve is controlled by the PCM (powertrain control module) and can be changed by having a custom tuning shop recalibrate the cars PCM...if you suspect the car is out of time you can have it check by a repair shop with a scan tool...if it is out of time it may need a new timing set or timing chain.