0
Ford Mustang
The Ford Mustang is a famous compact car built by the Ford Motor Company. The first manufactured Ford Mustang, a white convertible with black interior, was launched on April 19, 1964.
1,730 Questions
Can you put super unleaded in my 2002 v6 Mustang?
Yes. I put super unleaded in my 02 v6 mustang also.
What was the original list price of a base model 6 cyl ford mustang for 1965?
Hardtop: $2372 Fastback: $2589 Convertible: $2614
Where can i find a diagram for a 2.3 liter 1992 ford mustang engine?
When making changes to a car engine it is important to have a diagram. The 1992 Ford Mustang Engine diagram can be found in its maintenance manual.
How Much Does It Cost to Fix a knocking rod in a mustang?
it varies from motor to motor the rods are any where from 100 - 150 in a kit. then you need to find someone to put them in. you may just need to re torque the rocker arms
Where is the Fuel pump location for a Ford Mustang?
I have a 1990 mustang 5.0 . I just replaced mine. Its located inside the gas tank. Note if you decide to do it your self , before you drop the tank make sure its the gas tank is low., it makes it alot easier
How do you replace the main seal in a 302 mustang?
If it's a newer motor with the one piece rear seal, you can leave the engine in the car. Remove the transmission. Carefully pry the old one out with a screwdriver. Push the new one in evenly. I use a piece of wood and a hammer, and move it around the circle while tapping lightly until the seal is fully seated.
If your engine has the two piece seal, you'll have to pull the oil pan and the rear main bearing cap. It's possible to do it with the engine in the car, but the front crossmember will have to be removed to get the oil pan off. Be careful not to scratch the crank while removing the old seal.
The front seal is much easier to get to. Remove the crank pulley and dampener. You'll have to rent a puller from the auto parts store. Pry out the old and hammer in the new.
Unless your main seal is just pouring out oil, or you've got a freshly built motor with a improperly installed seal, just keep checking the oil level until you can completely rebuild it. It's not worth doing all that work on a worn out motor. Also check your pcv system. If pressure is allowed to build up in the crankcase, it can force oil past seals and gaskets.
What size gas tank in a 1989 Ford Mustang?
According to my Chilton's Auto Repair Manual :
A 1989 Ford Mustang has a ( 15.4 U.S. gallon gas tank )
The Mustang will rapidly devour anything that burns rice, but also feeds on Camaros, Firebirds, Challengers, Trans-Ams, and Javelins to name a few. In fact, its appetite for the Camaro was so great that these were once thought to be extinct, however small numbers of these have recently been spotted in the wild. Come on people, obviously the person who asked this didn't mean a car! Mustang horses will eat the same as any other horse- grasses and grains and such- and in captivity it would eat grain and hay like any other horse, but in the wild it would eat grass, leaves, bushes and shrubs.
What do the codes mean for Ford Mustangs?
It depends on the year. Check out this link:
http://www.mustangdecoder.com/plates.html#1965
My 1991 GMC Yukon dose the same and I cant figure it out but me being an Ase certified in NHRA top Fule drag racing I pull the hood latch and go to the hood and pull up it should just pop up.
How do you set timing on 1.8 92 escort gt?
You just turn the whole distributor loosen both bolts and turn slightly when the car is running.
What is overdrive on a Ford Mustang?
its acruising gear on all fords whether manual or auto so you save gas and your tranny goes into a higher gear, less torque on tranny
How do you remove the ignition cylinder on a Mustang?
get on the bottom of your car and push the ignition cylinder out
This works on '94's and newer...well, at least up to '04.
Step #1 is very important if you don't want your air bag to blow...
- Disconnect the neg. cable from the battery, disconnect the pos. cable from the battery, wait 2 minutes.
- Turn the ignition switch to RUN.
- Insert a 1/8 inch punch up through the little hole in the trim under the lock cylinder (you don't need to take any plastic off), hold the punch in while you pull out on the key. You should be holding the lock cylinder in your hand now.
Installation is almost the reverse (your battery is still disconnected, I hope):
- Push in the locking pin on the side of the new cylinder and turn the key so the cylinder is in the RUN position.
- Install the cylinder into the housing--fully seated and aligned with the interlocking washer.
- Turn the key to OFF. This lets the pin pop back out and lock the cylinder in place.
- Test the key by turning it from OFF to START. If that checks out, go to step 5 otherwise go back to 2.
- Reconnect the battery, Pos. first, then Neg.
A "mustanger" is a person who owns or is a mustang enthusiast.
I waved to Jake at the auto-parts store since he was a fellow "mustanger", knowing he owns a 1993 gt.
a mustanger is also someone who kills mustangs
Well there should not be a sleve in the crank snout where the seal lip rides. If there is one, then the crank has been reconnditioned/replaced, or there was damage to the snout, previously. I will recommend leaving the sleave, or replacing it with a new one if it has obtained rotational damage from the seal lip. This happens usually due to oil starvation at the lip ridding area or from a hardenned seal. The sleves may be purchased at your local autoparts and only serve to go over the damaged grove that the seal duged in. If the seal was not leaking and one is replacing the seal as maintenance or timing chain r&r. then leave the sleave in place other that that remove damaged sleve and replace with new one..Hope this helps.. Will..:)
What year was the first Ford Mustang introduced?
April 17 1964, dubbed as a 1964 1/2 model by Mustang fans.
