Ford Trucks and SUVs

For the 1997 and newer Ford F-150 , with the 4.2 liter V6 engine :

With engine oil filter change :

( 6.0 U.S. quarts )

It takes a special wrench set to remove the fan assy. Check with your local discount auto store Hope this helped Good Luck

Clutch Safety Switch? Usually located at the upper end of the clutch pedal under dash area

A lorry does

1000

1 - 3 - 7 - 2 - 6 - 5 - 4 - 8 The distributor rotor turns COUNTERCLOCKWISE The engine cylinders / spark plugs are numbered : FIREWALL 4 - 8 3 - 7 2 - 6 1 - 5 FRONT

slight knock when turning can be caused by a loose wheel bearing,worn ball joints,or ball joints that need grease,can also be caused by a worn bearing in side the steering column,or worn out shock absorber.

185@3800 RPM

My 1970 ford f100 Ranger is a 360 three on the column and it's stock gas tank holds 20 gal. but there are other gas tanks you can put on it that are larger or smaller. Check out LMC truck company, that's where I get all my parts

If you drive a Ford truck and things start to go wrong with it, like you are hearing strange noises or it is stalling on you or it just won't start, you need to get it into a mechanic as soon as possible. One problem that seems to be happening with the Ford trucks are the coil are going bad.

10 degres

When you have a big vacuunm leak your car is not going you be able to suck the gas it needs into the intake because, the air it needs to do that, is coming from somewhere other than the throttle bore. So to stay running, the choke will have to be partially closed to help suck more gas down the intake. I know this because I asked the question yesterday and found out for myself today by trial and error!

it will fall right inYou will have to modify the exhaust to match the manifolds, and if you do not use the electrical harness from your 302, you need to make sure to swap the engine computer. The 352 does not use a pressure sensor on the power steering pump and will cause the check engine light to come on. You can splice the connector from the 302 harness into the vehicle wiring, the 351 harness does not have the pins on it's side of the harness.

its located at the rear drive axle

A truck that can do housework

backfire is the best! rubbish! loosers L

No adjustment for the ignition timing on this vehicle. It is computer controlled. It's computer controlled off of the cam position sensor (It's in the hole where the distributor used to go) and the crank sensor.

Farm.

The standard horsepower of associated with a 1995 351 cubic and Ford engine is 215. The engine horsepower was available in several different options.

1997 2 wd and 4wd both use the same size wheels. later models and bigger pickups have different sizes no 4wd use 17" and 2 wd use 16"

Not a direct fit, 351 C uses the small block bell housing, the 352 is a FE model engine, look for 360, 390, 428, 406, 427, 410, you can change to the small block or the 351-400 modified by changing the engine stands and exhaust systems and their mating transmittions

In British-speak it is the trunk.

its in the engine compartment on the passenger side about mid way its a little metal box with 2 wires bolted on the box is mounted to the passenger firewall with 3 7mm screws real easy to change

F100 is a ford F100 half ton pick-up and 4.9l is the engine size. 4.9l is a 300 cubic inch inline 6 cyl.

Ok final found it again go to [http://www.drivetrain.com/transillm5r1_m5r2.html Drive Train.com] Good Luck and Remember.
Change Your Mind, Not Your Oil.
Use the First In Synthetic Motor Oil's.
See My Bio For Information & Contact Details.