Hyundai Excel

To remove the gearbox from a Hyundai Excel, first, ensure the vehicle is securely lifted and supported. Disconnect the battery, then remove any necessary components such as the drive shafts, linkage, and crossmember. Unbolt the gearbox from the engine and transmission mounts, and carefully lower it from the vehicle. Be sure to follow safety procedures and consult the vehicle's service manual for specific details and torque specifications.

In the 1998 Hyundai Excel, the fuel pump relay is typically located in the engine compartment, specifically in the relay/fuse box. This box is usually situated near the driver's side of the engine bay. You may need to consult the owner's manual for precise details, as the layout can vary slightly based on the specific model and configuration.

In a 1998 Hyundai Excel, the tacho wire, which is used for the tachometer signal, can typically be found at the ignition coil or the ECU (engine control unit). You should look for a wire that is connected to the ignition coil's negative terminal, as this wire usually carries the RPM signal. Alternatively, you may find it in the wiring harness connected to the ECU. Always consult the vehicle's wiring diagram for accurate identification.

To replace the gearbox oil in a 1999 Hyundai Excel, first ensure the vehicle is on a level surface and secure it with wheel chocks. Remove the drain plug located at the bottom of the gearbox and allow the old oil to fully drain into a suitable container. Once drained, replace the drain plug and remove the fill plug, then use a pump to add the appropriate type and amount of new gearbox oil until it reaches the fill level. Finally, replace the fill plug and check for leaks.

For a 1994 Hyundai Excel, it's recommended to use power steering fluid that meets the specifications of either Dexron III or a similar automatic transmission fluid (ATF). Always consult your owner's manual for the most accurate recommendations. Make sure to avoid using any fluids that contain additives not specified for your vehicle, as they can cause damage to the power steering system.

In a 1999 Hyundai Excel, the brake light switch is typically located near the top of the brake pedal assembly. It is mounted on the bracket that holds the brake pedal and is activated when the pedal is pressed. To access it, you may need to remove the lower dash panel for better visibility and reach. If you're having issues with the brake lights, checking this switch can help diagnose the problem.

The torque settings for a Hyundai Excel rocker cover typically range from 7 to 9 ft-lbs (or 9.5 to 12.2 Nm). It's important to follow a specific tightening sequence, usually starting from the center and working outwards to ensure even pressure. Always consult the vehicle's service manual for the exact specifications and procedures, as they can vary by model year.

To unlock the radio code for a 1997 Hyundai Excel, you typically need to retrieve the serial number from the radio. This can often be done by removing the radio from the dashboard and checking the label on the unit. Once you have the serial number, you can contact a Hyundai dealership or check the owner's manual for instructions on obtaining the radio code. Some online resources may also provide assistance based on the serial number.

In a Hyundai Excel, the fuses for the power windows are typically located in the fuse box, which is usually found under the dashboard on the driver's side or in the engine compartment. You can refer to the vehicle's owner manual for a diagram that identifies the specific fuse for the power windows. If you're experiencing issues, check the fuse for any signs of damage and replace it if necessary.

To remove the ignition barrel from a Hyundai Excel, first disconnect the car battery to ensure safety. Next, remove the steering column covers to access the ignition assembly. Insert the key and turn it to the "On" position while pressing the release pin or tab on the ignition barrel. Finally, pull the barrel out gently, making sure to disconnect any wiring harnesses attached to it.

To replace the fuel filter on a 1999 Hyundai Excel, first ensure the vehicle is turned off and the fuel system is depressurized. Locate the fuel filter, which is usually found along the fuel line under the car, near the fuel tank. Disconnect the fuel lines from the filter using appropriate tools, then remove the old filter and install the new one, ensuring the directional flow matches the markings on the filter. Finally, reconnect the fuel lines, check for leaks, and start the vehicle to ensure proper operation.

The transmission filter for a 2005 Hyundai Elantra is located inside the transmission oil pan. To access it, you'll need to remove the transmission pan, which involves draining the transmission fluid and unbolting the pan. Once the pan is off, you can replace the filter, which is typically clipped or bolted in place. Be sure to use a new gasket when reassembling the pan to prevent leaks.

To open the radiator in your Hyundai Excel, first make sure the engine is cool to avoid burns. Locate the radiator cap, which is usually on top of the radiator, and turn it counterclockwise to release any built-up pressure. Once it's safe, you can fully remove the cap to access the coolant. Always check the owner's manual for specific instructions related to your model.

To remove the door panel from a 1995 Hyundai Excel, start by disconnecting the negative battery terminal to prevent any electrical issues. Next, locate and remove any screws securing the panel, typically found near the door handle and along the bottom edge. Carefully pry off the panel using a flat tool to detach any clips, being cautious not to break them. Finally, lift the panel upwards to detach it from the door frame, and disconnect any electrical connectors for power windows or locks if equipped.

To change the license plate bulb on a 2007 Hyundai Sonata, first, open the trunk and locate the license plate light assembly. Use a flathead screwdriver or a similar tool to gently pry off the lens cover. Remove the old bulb by turning it counterclockwise, then insert the new bulb by turning it clockwise into the socket. Finally, reattach the lens cover and ensure it is secure.

If the fuel gauge in your 1997 Hyundai Excel isn't working, it could be due to a faulty fuel sending unit, a broken wiring connection, or a malfunctioning gauge itself. First, check the fuses related to the fuel system for any issues. If the fuses are intact, inspect the wiring and connections at the fuel tank and the instrument cluster. If all else fails, consider consulting a mechanic to diagnose and repair the problem.

To replace the rear shock absorbers on a 1996 Hyundai Excel, first, safely lift and support the rear of the vehicle using jack stands. Remove the rear wheels to access the shock absorbers. Unbolt the top and bottom mounts of the shock using the appropriate socket and wrench, then remove the old shock absorbers. Install the new shocks by reversing the removal process, ensuring all bolts are tightened to the manufacturer's specifications, and then reattach the wheels before lowering the vehicle.

To replace the fuel pump in a 1994 Hyundai Excel, start by disconnecting the negative battery terminal for safety. Remove the rear seat cushion to access the fuel pump access cover, then disconnect the fuel lines and electrical connectors from the pump. Unscrew and lift out the old fuel pump assembly, then install the new pump in reverse order, ensuring all connections are secure before reassembling the seat and reconnecting the battery. Finally, check for any leaks and ensure everything is functioning properly.

On a 1998 Hyundai Excel, the fuel pump relay is typically located in the engine compartment fuse box. To access it, open the hood and locate the fuse box near the battery. The relay may be labeled, so refer to the diagram on the cover for identification. If you're still having trouble, the owner's manual may provide additional guidance.

I'm attempting the same thing in my Mother-In-Law's 1996 Hyundai Accent. I've found that you need to start by removing the ashtray to expose the 2 screws on either side of the ashtray (inside). Remove these screws, then gently pry the center dash away (some of the clips might spring, but you can replace these later.

That's as far as I have gotten so far. There seems to be another fastener someplace in the lower left portion of the center dash that holds it in place. I am working to get this removed, but to no avail.

This Might sound simple but it's a pig..... Good LUCK.

Remove the Ashtray, Remove the 2 screws in the ashtray compartment! Now you need to undo the heater control clips 2 under the drivers side then 1 behind the glovebox.(this took me 2 hours to find!!!!!!!!! Then slide center control unit out. You then have to undo the stereo retaining screws and slide the stero out.... You might have to take the cables off the clock and hazzard lights too. Replace in reverse order and hay presto you are done!!!! Shame I didnt have this info before starting!!!!! Oh well it's done now!!!!!!!!!!!!

I could not see the 2 clips until I removed the cover plate under the steering wheel. Once I could see the heater control cables it was obvious what was being said. I disconnected them and the one behind the glovebox and all proceeded as stated above.

I paid a mechanic to do it for me when buying the head unit, it took him an hour including installing two speakers because he had to remove the entire heating unit... so he says to take the stock CD player out and install the new one.