Industrial Engineering

technically nominal wall thickness refers to pipe wall thickness (average)..if you are referring to shell/hull/fore part of a vessel, the thickness varies depending of type, size, deadweight of the vessel

A train DUHHH!

An external combustion engine.

It is a jig used in hand planing and cross cutting to length. You clamp it in a vise, or let the lower edge overhang the edge of a workbench. The purpose in using one is generally to avoid cutting your bench top with a saw.

It is mechanized and therefore is less time consuming than using tools, and requires less manual labour, therefore being cheaper than, for example repoussé, which uses tools to handcraft a raised pattern.

Since the x coordinate will change, but not the y coordinate, take (x,y) and reflect across the y axis and you have (-x,y)

The man to machine ratio is commonly used by organizations to calculate production output. It is a helpful way of correlating the amount of expenses and resources put into an investment versus the return. It is important to establish optimal man-machine ratio to gain high resource utilization and output

full form of CGS 680 ROD= CONTROLLED GRAIN STRUCTURE

A weld stud made by Nelson Stud Welding, Inc.

Any controller used in motors or electrical drives are only to get variable speed or variable torque or to get higher efficiency.

The controller can be anything, it might be micro controller or it can be DSP controller or may be other.

But DSP controller finds some advantages over micro controller.

Both the controllers are Digital controllers only, but DSP controller has inbuilt Analog to Digital converter, inbuilt Digital to analog converter , inbuilt counter and inbuilt pulse generator.

With a micro controller we need to assemble all the above converters, counters and pulse generators externally, so DSP based electrical drives are more popular though the cost is more compared to micro controllers.

The voltage induced into the secondary winding will be lower than the voltage applied to the primary winding. The primary winding being the winding connected to the supply, while the secondary winding is the one connected to the load.

It means that one part can be substituted for another. The two components aren't always identical, although they both serve the same purpose.

Its Skilled Worker Program for Indian Student.

There are really bright chances to be settle in Canada for Qualified Indian Students.

20 colleges under SPP Canada all colleges are Govt. Approved colleges.

4250

The volume displaced to indicate a given change in Specific Gravity; e,g., 0.001, is less in higher SG liquids. If you do the math for a typical lab hydrometer, you will find that in a liquid with a SG near 1.100, you will have about 20% less stem travel than when it is near water at 1.000. The key to remember is that the weight of the liquid displaced is equal to the total weight of the hydrometer, not just the portion of it that is submerged.

It depends. The 2A current, did you measure that while the soldering iron was on? Or is it rated at 2A current consumption on the device itself (on the powercable or the stem of the soldering iron). Generaly speaking you can calculted the real power consumption by using P=V*I (thus 2A*24V = 48W). But do remeber that this power consumption is in the steady state, that is, after its switch on and all transient effects have died down. To be safe allow for 3A-4A switching currents that occurs at power on.

1. By increasing size and improving design. 2. By injecting hydrocarbons (the C in these means less coke is needed so there's more space in the shaft for the ore) 3. Enriching the blast air with pure O2 (this increases the flame temperature where the air gets heated and it increases the production of CO.) 4. Higher pressure at the top of the blast furnace (it increases the flow rate of the gas without increasing its velocity) and 5. By changing the physical and chemical properties of the raw materials.

It is more accurate, a 4 wire is more accurate than 3 wire and 3 wire is more accurate than 2 wire.

1- It doesn't need a power source or fuel.

2- its cost is relatively low.

3- it is available for several fluid.

4- it can be used for both vertical and horizontal directions.

Elements of both but the molten rock pyroclastic flows (Mauna Kea , Hawaii) are hydraulic, the Mt. St Helens eruption was to a large extent pneumatic as the water turned to steam.

IE3000 are industrial grade switches. The series consists of multiple modules that can be plugged into each other.

This time is needed for just starting the spare feed pump...

to make it insulated and rust free Gi spray is used.

Fiberglass is easy to install and can be purchased in insulation sleeves. The insulation is comprised of inorganic fibers, which are bonded with special resin. An aluminum-foil facing or vapor retarder is attached. The insulation is usually available in 3-foot sections.