How do you install exterior door handles on a 95 jeep wrangler?
They can be removed and replaced from inside, you need to remove the inside door panel to get access, then its a few clips on the sides.
Can you put a 1989 Jeep Wrangler YJ on a 1998 TJ Jeep Wrangler?
The tops will not fit without modification
What is the difference between a Jeep Wrangler Sahara and a Jeep Wrangler YJ?
The difference between them is about $5,000.00 and some bling they are both wranglers.
Captain911
What causes a 95 jeep wrangler to be hard to start?
if you have done a tune up then it is more likely to be fuel pressure check valve on the top of your fuel pump get a fuel pressure gauge you can borrow one from most auto supply shops and you can check it at the blleed line on fuel rail it should be 42 lbs if it is even a little low it is your check valve you can find one on ebay so you dont have to buy the whole fuel pump check this out i have had it on three of my 90s wranglers
How much does jeep hard top cost?
You can find them used anywhere from 200 to 600 dollars, check the classified ads in your area.
auto zone...has the frount speakers for my 1999 jeep wangler.. try auto zone they might be the same speaker as the frount ones ..around 15 dollars each.. t.man berryville va.
you should pass them through one of the existing rubber grommets that are already there for the wiring harness, you can also route the wires along the loom or inside the protective cover for a cleaner install.
How fast can a 1997 Jeep Wrangler go?
According to the speedometer, 100 miles per hour, but it is not advisable.
How do you lock the hubs on your 1988 Jeep Wrangler?
Turn the dial on the wheel hub to lock position.
To unlock, turn it back.
If you look at the center of the front wheels, you will see it.
What is the oil grade and capacity for a 2004 Jeep Wrangler X?
4 cylinder 5 quarts 10w30
6 cylinder 6 quarts 10w30
Why does my 1993 jeep wrangler turns over fine but not getting any fuel?
If a 1993 Jeep Wrangler will turn over but does not get fuel there is a problem with the fuel pump or fuel lines. A licensed mechanic will be able to run diagnostic tests to see where the problem lies.
How do you replace the alternator on a 1995 Jeep Wrangler?
Disconnect the battery. Unplut the altenator, disconnecting the plug and taking off the belts. Unbolt the altenator, and bolt the new one on. Reconnect the belts, then the plug and finally reconnect the battery. Voila! You replaced the altenator!
Tools required: 7mm, 10mm, and 15mm sockets and 15mm box wrench or adjustable wrench.
Tips - for easier access, first remove the jack assembly, and the passenger side tension rod.
1. Disconnect the battery. 2. Release tension from the serpentine belt by loosing the bolt located to the left of the power steering pump (2.5L) - uses 15mm socket. 3. Belt should now easliy lift off of the alternator pully. 4. Unbolt the alternator - 15mm socket. 5. Disconnect the 5 power connectors - 7mm and 10mm sockets. 6. Remove alternator. 7. Install new alternator by reversing previous steps.
Have a new battery on hand, most likely the old one will be dead as well. Also, the serpentine belt must be VERY tight. You shouldn't be able to flip the belt over, or flex it much at all. If your engine squeals at low RPM's - tighten the belt.
1992 Jeep Wrangler sparkplugs 4.0?
Please let us know what you are needing help with your wires.
It has six spark plugs. if you ask auto zone or tell somone here whats going on than we can help. if you do not know, take the jeep to auto zaon or other and they will tell you what you need.
Where is the diagnostic connector in a 1990 Jeep Wrangler?
On the 1990 jeep with 4.2 Engine, the connectors are under the hood on a bracket right above and to the left of the battery. There are 2 plugs, both with beige rubber boots over them.
What year hardtops will fit a 1994 wrangler?
Any 87 thru 95 Wrangler, and possibly CJ, but the doors may be different.
How do you Stop Change oil Warning in a Jeep Wrangler?
What year are you talking about? Mine just started doing this (2007.) Since I'm doing my own changes, I'll have to figure this out too. However- I'm pretty sure it's covered in the glovebox vehicle manual.
How easy is it to replace an ignition switch on a 1994 Jeep Wrangler?
You did not clarify whether you meant the switch or the lock cylinder that drives the switch. Either way, it is a complex job that requires special tools and a high degree of mechanical ability. In essence, you will have to remove the entire steering assembly if you need to replace the switch. If it is just the lock cylinder, it is considerably easier but still complex requiring removal of horn, turn sig, hazard and other assemblies. I have done this on an 89' and 93' Wrangler, a 94' shouldn't be much different. If you need details, e-mail me at: iancarah@yahoo.com...but to answer the question: It is not easy.