0
Pontiac Sunbird
The Pontiac Sunbird was a subcompact, four-passenger car produced from 1975 to 1994 by General Motors’ Pontiac division. This model was offered in notchback coupe, station wagon, sedan, hatchback and convertible body styles.
617 Questions
What the problem when a Pontiac Sunbird LE won't start?
My Pontiac Sunbird wasn't starting for a friend of mine, and I had never had the problem. But I figured out that you have to be in First gear to start it, so check that. Also there might be a bad starter or something like that. Hope that helps
Rovert
What kinds of transmission came with the pontiac sunbird le 1994 1g2jb54h8r7531872?
The 1994 Pontiac Sunbird LE was typically offered with either a 5-speed manual transmission or a 4-speed automatic transmission. The manual transmission provided a more engaging driving experience, while the automatic offered convenience for daily driving. Specific transmission options could vary depending on the engine choice and market, so it's essential to check the vehicle's specifications for confirmation.
Were is the map sensor in a 91 Pontiac sunbird?
In a 1991 Pontiac Sunbird, the manifold absolute pressure (MAP) sensor is typically located on or near the intake manifold. It can be found mounted on the engine, often near the throttle body or at the rear of the engine bay. To locate it, look for a small cylindrical sensor with a connector and vacuum hose attached. If you're having trouble finding it, refer to the vehicle's service manual for specific details and diagrams.
Where do the long head bolts go on a 1994 Pontiac sunbird LE 2.0?
On a 1994 Pontiac Sunbird LE with a 2.0L engine, the long head bolts are typically used in the center of the cylinder head. When installing the cylinder head, place the longer bolts in the designated holes that are usually located in the middle section of the head, as these areas require additional support. Always refer to the vehicle’s service manual for the correct torque specifications and bolt placement to ensure proper assembly.
Where is the torque converter switch located on a 1991 Pontiac sunbird?
On a 1991 Pontiac Sunbird, the torque converter switch is typically located on the transmission, often near the valve body or attached to the transmission control module. It may also be found on the throttle body in some configurations, as it works in conjunction with the engine's throttle position. For precise location details, it’s best to refer to the vehicle's service manual.
It sounds like the issue may be with the heater control valve or the actuator that controls the airflow direction. First, check the linkage connected to the lever for any disconnections or damage. If the linkage is intact, inspect the actuator for proper operation; it might be stuck or faulty. If necessary, you may need to replace the actuator or the entire control assembly to restore function.
How do you reiease a hood latch with a broken cable on a 1988 sunbird?
To release a hood latch with a broken cable on a 1988 Sunbird, you can try accessing the latch directly from underneath the car. Use a long screwdriver or a similar tool to maneuver and pull the latch mechanism towards you. Alternatively, if you can reach the area around the latch, you might be able to manually pull the release lever. If these methods don't work, consider removing the front grille to gain better access to the latch.
The issue with a 1994 Pontiac Sunbird quitting after running for a while and then stalling when put into gear could be related to several factors. Common causes include a failing fuel pump, which may not provide consistent fuel pressure when hot, or a faulty ignition system, such as a bad ignition coil or spark plugs. Additionally, a malfunctioning torque converter or transmission issues could also contribute to the stalling when the vehicle is placed in gear. It's advisable to perform a thorough diagnostic to identify the exact cause.
How do you change gear linkage cables on a vauxhaull movano?
To change the gear linkage cables on a Vauxhall Movano, first, ensure the vehicle is securely lifted and supported. Disconnect the battery, then remove any necessary panels to access the gear linkage assembly. Unclip or unscrew the old cables from the gear lever and the transmission, and replace them with the new cables, ensuring they are securely attached. Finally, reassemble any removed parts, reconnect the battery, and test the gear shifting to ensure proper installation.
How do you replace ignition cylinder in a 93 Pontiac sunbird v6?
To replace the ignition cylinder in a 1993 Pontiac Sunbird V6, start by disconnecting the negative battery cable to ensure safety. Remove the steering column cover by unscrewing the screws and gently prying it off. Insert the key into the ignition and turn it to the "Run" position, then locate and depress the pin or release tab on the ignition cylinder to pull it out. Finally, insert the new ignition cylinder, reassemble the steering column cover, and reconnect the battery.
