0
Remote Control Devices
A remote control device is commonly an infrared device used to control electronic devices such as televisions and DVD players. It is usually powered by AA or AAA size batteries.
2,009 Questions
It may take some searching but try these three ways:
Get in to your local Radio Shack when they aren't busy and talk to the staff. Most of the staff there have a personal interest in electronics and if you get lucky, you'll find one that may have information to help you.
Next, try telephone calls and emails to RCA. Even if they only release circuit diagrams to dealers, you might be able to talk to someone who can let you know the values of the resistors you are after.
Finally, find a forum that discusses electronic repairs and equipment. Get the right forum and there will be someone who may have detailed knowledge of the product.
Happy hunting.
Need factory override code for Panasonic cq-vd7500u?
If you are talking about resetting the id code, you must hold down the right tracking button for ten seconds. It will enter the last known code for you. Then you can go into the menu and change the id from there.
What is the att uverse remote code for a toshiba 42hm66 dlp projection tv?
I just used a Zenith code 1255 for my Toshiba HDTV and it worked! Good Luck!
Is a mpeg audio file the same as mp3?
Not necessarily. Although the most common MPEG audio format, there are also other standards, both previous to and successive to MP3. MPEG Audio Layer 1 (MP1) and MPEG Audio Layer 2 (MP2), as well MPEG-4 Part 3 could be classified as an "MPEG audio file."
Ge universal remote rc24914e and you need the code for a sony DVD player dvp-ns400d?
MANUALLY ENTERING CODES
1. Manually turn on the device (TV, VCR, DVD, etc.) you wish to
program.
2. Press and hold the CODE SEARCH/SETUP button on the remote
until the INDICATOR LIGHT lights, then release.
3. Press and release the button for the device you are programming
(TV, VCR, DVD, etc.). For AUX, press AUX then the device button
you are assigning to AUX. The INDICATOR LIGHT will blink then
remain lit.
4. Enter the three or four digit code for your device using the number
buttons in the GE Universal Remote. After your code is entered the
INDICATOR LIGHT will turn off.
5. Aim the remote at the device (TV, VCR, DVD, etc.) and press the
POWER button. Your device should turn off.
Note: If your device does not respond to the first code listed,
repeat steps with the next code. If none of the codes listed for your
device work for your device or your brand is not listed, try the Code
Search method described below.
USING CODE SEARCH FUNCTION
If your TV, VCR, DVD, etc. does not respond after you have tried all the codes
for your brand or if your brand is not listed, try searching for your codes by
following the steps below.
1. Turn on the device you wish to program.
2. Press and hold CODE SEARCH/SETUP until the INDICATOR
LIGHT lights, then release.
3. Press and release the device button for the device you are
programming (TV, VCR, DVD, etc.). The INDICATOR LIGHT will
blink once then remain lit. For AUX, press AUX then the device
button you are assigning to AUX.
4. Press and release POWER until your device turns off. Wait at least
2 seconds between each time you press POWER. Important: You
may have to press POWER up to 250 times.
5. When your device turns off press the ENTER/SAVE button. The
INDICATOR LIGHT will go off.
Adventures in Dinosaur city
How do you program Philips universal remote for mediacom cable?
I purchased a Philips model# SRU5107WM17 remote and had same problem with my Mediacom cable/dvr. Could not find the codes in the in package nor on the Philips website. I had to do some research. Not sure what brand of cable box you have but I have PACE and the Motorola codes worked for my Pace cable/dvr box. The code I used was 1077. If Motorola codes don't work, the Scientific Atlanta codes work for some Pace cable/dvr boxes. It is a shame that between Mediacom and Philips don't help customers out better.
What is the difference between a remote control car and a raido control car?
Generally remote control cars are controlled via either a cable or infared, where as radio controlled cars are strictly controlled by radio waves. However radio controlled cars can also be described as remote controlled.
A control break occurs when a program?
passes logical control to a module contained within another program
What is the use of the control room in a substation?
Environmental and structural condition monitoring and protection is the use of the control room in a substation.
Specifically, a control room exists to make sure that the well-being of equipment, people and structures is realized. It may be the location for equipment which keeps a substation's ambient conditions -- such as air conditioning, heating, lighting, power -- respected. Its staff may have special expertise in maintaining the facility's security and structural integrity.
Nad receiver code for comcast remote?
... I have a a NAD receiver and its remote control unit is not fully functioning i.e., I did replaced with new batteries yet it does on control the functions in the receiver. Whatever the keys I just press on the remote, I find the light and that is all, just the light on the keys but no functions at all.
What could be the reason for it? I also notice, a tiny red colour butten just on the middle of the remote and it reads LEARN. Should we need to reset this or what I really should do.
Please help me
Jazeel, ajmjazeel@yahoo.com
I have a Remote control but dont have the codes to program it?
Owner's Manual
If you don't have one copy and paste link below;
Is there a remote that works for all electronics?
Yes, there are Universal remote controls which can use for various electronic goods. There are many website selling Universal remote controls. Kindly refer to link : http://www.universalremote.com/
Who invented the remote underwater manipulator?
It was first invented in 1986, I got that from my textbook so it should be right.
