Unanswered | Answered

Radio

~13200 answered questions
Parent Category: Music
A radio refers to an electronic device that works by receiving radio wave (an electromagnetic wave) that has the capacity to broadcast news, speech, music and other audio through the air.
there should be 4 nuts on the back side of the steering wheel look for the holes and once you get those off it should just be pulled out towards you.   probably should remove the srs fuse prior to any disassembly   Before attempting any disassembly of an airbag-equipped steering wheel,…
Popularity: 36
Go there... Everything you need is there!http://ccs.exl.info/frame_installation.htmlHave a nice day!!!JMoney69
Popularity: 83
The panel that surrounds the stereo will pop right out afterwards lift and pull the original CD player out. Go down to the local walmart or some one who specializes in car audio equipment and buy the correct wire harness for your year make and model. Match up the wiring harness wires with the wires …
Popularity: 62
i an not 100% sure on this one, but i am pretty sure that under the bonette there is a black fuse box as is under my wife's corolla. there are fuses for interior lights and a few others. there is a diagramme showing which one does what, otherwise, near your feet kick panel just inside the front doo…
Popularity: 81
Take your car to the vw dealership and they will give will put the code into your radio, however they will most likely charge you $100 dollars for getting the code for you and putting it in the radio. I see about 3-4 cars a day come in for radio codes so once you get that code keep it in a safe plac…
Popularity: 39
To remove the radio on a Chevy Caprice, pull of the volume and tuner knobs. Loosen the nut holding the radio in on each spindle. Then disconnect the wires on the back of the radio and pull out by pushing it backwards and reach up under the dash to retrieve it.
Popularity: 1
Call a GM dealer. With the serial number of the car, he'll give you all the responses you need.Have a nice day.JMoney69   The time controls are what you use and you use the minutes first and then the hours. The vehicle has a default code found in the owner's manual.Thank you, Rednek1986
Popularity: 67
First off there are a series of 7 or 8 mm screws in the dash. one behind the the fuse box cover on the drivers side and one on the passenger side. then you open up the glove box and there should be a set of four 7 or 8 mm screws to be removed. if you look in the glove box there is a cavity that is r…
Popularity: 17
Try this. Turn radio off. Push and hold down power button. Push scan and/or seek up or down to set clock. This works with some Chrysler radios.   TURNN RADIO OFF PUSH AND HOLD VOLUME NOB USE SEEK AND SCAN FOR HOURS/MIN.
Popularity: 103
On my 1995 Lebaron you just pop off the plastic housing surrounding the radio and air vents (it's pretty big). Then unscrew the screw on the right top side and bottom left side and pull. Be careful to disconnect the wires before the radio is completely out.
Popularity: 76
You do not need to remove the dash. Take out the ash tray (by pressing down the lever as you pull it out)Starting at the sides, pull firmly on the plastic trim through the ash tray opening. The trim will start to pop off. Be careful not to pull to hard, as the trim is attached by small plastic tabs…
Popularity: 70
The fuse is located either under the dash or in the engine department. If you look they should all be labeled. In addition there is a handy fuse puller located under the dash as well. ! It us under the hood to the right of the battery (labeled) once you remove the fuse box cover and yes there is a…
Popularity: 68
I had this exact problem on my 1996 Taurus. The solution in my case was to replace the transmission range sensor. I replaced it myself. It was easy to change. I can't say if that is what is wrong with your Taurus, but it was what was wrong with mine. Good Luck!   This was also the problem w…
Popularity: 59
There is a small "inline" fuse on a separate wire to your radio. This is so that there is power on always to keep all your preset stations. Also check behind the radio and make sure the antenna connection hasn't vibrated loose. You didn't say if the lights on the radio were on or off or if the speak…
Popularity: 84
Input your identification number by pressing the preset buttons in sequence. The identification number is on the User Card that came with your Hyndai. If an incorrect identification number is entered 3 times, it will not be possible to cancel the incorrect number until one hour has elapsed with the …
Popularity: 95
%REPLIES% Answer For some reason the radio isn't filtered correctly. I would go to Radio Shack and get the best filter they have and try that. Also if the antenae is broken sometimes that will be the cause. Goodluck, JOe Answer there is noise filter in the radio, also on the coil pack may…
Popularity: 76
you need radio tools,i found mine at walmart,they look like a big u,they come two to a pack, insert tools in holes beside radio,spread slightly toward outside with thumbs while pulling.   I was able to do this on my 1995 model by cutting a wire clothes hanger and making two u-shaped horseshoe…
Popularity: 99
Hey Rene==No!! Just take off the knobs and under them are nuts to remove. Also there are several brackets under the dash to take loose. Good luck, Joe  CommentI found earlier today that you *do* need to remove the dash. Here's how:1) Open the passenger door. On the part of the dash that is aga…
Popularity: 74
You should be able to get a wiring harness from a locally-owned or small business type car audio shop that also does install. Usually the small businesses have better access to get the "odd ball" parts than do Circuit City and Best Buy. If they can't order it, ask one of the guys in the install bay …
Popularity: 69
To remove the panel across the dash that covers the radio, the air deflectors must also be turned to one side and gently pushed down on with a flat tip at the top and pulled out. Get the flat tip right next to the pin to depress the tab. There are four additional screws behind them and failing to re…
Popularity: 108
go to installdr.com they have a wide variety of free information that pertains to car stereo wiring information. You can use a AAA battery to find out what speakers are what; with the car battery disconnected put one end of the wire on on terminal and keep trying different wires on the other end unt…
Popularity: 92
If you are parked and you want to here the radio without the Automatic headlights on. Some times if you engage the parking brake it will turn off the automatic head lights.
Popularity: 46
That's easy, I did the same job to my 90 accord. First buy a fixed antenna, I went to radio shack, something like $12, instead of $200+ for the power antenna from Honda.. In the trunk, on the side of the antenna, pull back the trunk liner but be careful not to break an clips. once the trunk liner i…
Popularity: 115
To replace the radio antenna on the 1990 Jetta you simply unscrew it (counter-clockwise) and screw the new one clock-wise.   If you are replacing antenna with off the shelf productYou will probably have to remove the wheel, wheel well fender protector, to have access to the bolt for the anten…
Popularity: 76
Hey Nicole==TAke the knobs off and remove the nuts under them then get under the dash and remove the wiring and any nuts holding the rear of the radio. GoodluckJoe
Popularity: 55
Answer There are three plugs in the back of an Echo radio. Before I blew the fuse, this is what I had figured out. The black one, of course, is the antenna. The other two plugs are white(5 wires) and blue(8 wires). The white plug is mainly speaker wires. The blue plug has speaker wires and the po…
Popularity: 68
Depending on the set up. The hour/ min buttons are located on the lower right corner buttons if it is a CD player. Hold the buttons down to set the time. If you Cavalier has a set button, hold it down and while the set light is on use the seek and scan buttons to set the clock. If your 2002 Chevy …
Popularity: 77
If you are asking how to remove the dashboard trim, remove the ash tray to access two screws holding the panel in. After removing these two, the panel just snaps in.If you are asking how to remove the radio itself, Ford uses a snap-in mount to speed up assembly. The only way to remove it is with the…
Popularity: 94
GM DELCO THEFTLOCK RADIO UNLOCK CODESINCE YOU ALREADY HAVE THE CODE CALL THIS TOLL-FREE NUMBER, ITS A PRERECORDED MESSAGE SO YOU DON,T HAVE TO TALK TO ANYONE; 1-800-537-5140. THE VOICE WILL ASK YOU IF YOUR CALLING FOR CHEVY, PONTIAC, CADILLAC, ECT. PRESS #1 FOR CHEVY, PRESS 206010 AND HIT THE # KEY.…
Popularity: 97
Take the knobs off and the nuts under them. Then take off any bolts in the rear holding it and remove the wireing.
Popularity: 107
remove the plastic piece just above cup holder. It just snaps into place and can be pulled out by hand. This exposes two screws that hold bottom of radio assembly. In side the a/c vent just above the a/c control panal there are two small metal snaps. Yoy can use a screwdriver to push them out of the…
Popularity: 108
Try AUTOBOOKSONLINE.COM If they don't have the wiring diagram separate they may have a shop manual
Popularity: 34
First what year is it? If it is a 2000-2003 you will need to remove the dash pad itself to remove the cover for the radio. There are screws on both sides of the dash where the fuse panel is on the driver side and passenger side, also open the glove box there are two ontop in the front use a flash li…
Popularity: 94
CK FOR LOSE GROUNDS OR MAYBE A SHORT A module controls electrical accessories that should be died when the car is off. Those items include the radio and power windows. The module in that era of Firebird was later redesigned. Replace that module with the newer version.
Popularity: 79
I just installed a new CD player into my 97 Saturn SL 1 using this, it should work for your 1994 SC2 because its for 90's and above.http://www.installdr.com/Harnesses/GM-Wiring.pdf
Popularity: 68
Depending on what style of radio you have that makes a difference any car audio shop should have the info if not you should be able to retreave the info from the dealer.
Popularity: 48
%REPLIES% Answer The headlights probably have a bad ground. Answer the alternator is probably going bad.
Popularity: 48
First you take the dash (trim)molding from around the radio then you can get to the four screws that hold it in. All you do then is slide it out. RAy
Popularity: 103
TAke the knobs off and there are nuts under them that need to be removed.
Popularity: 40
I don't know if this will work on this perticular car but it works on a bunch. Press the set button and change the hours by pressing the seek button and the minutes by pressing the scan button. Try it.   Assuming you have the Philips RC600 system, here are the instructions (quoted directly fr…
Popularity: 86
Use the removal tools to pull the radio assembly out of the dash - note: you do NOT need to remove the plastic trim piece! :) Insert the tools into each pair of small holes on either side of the radio face They're all the way in when you feel them hit an indent, or a bit of 'click'Push the tops of t…
Popularity: 461
%DETAILS% Answer so ford radios have a stock amp. located in the back of the car. You have to buy a special harness to bypass this. Check out a great site called installer.com
Popularity: 32
Remove the plastic cover surrounding the stereo and air conditioning knobs/vents. Use a flat screwdriver with the tip covered with tape (not to scratch anything). Slip the screwdriver under the plastic cover and pry off, not too hard. If you wiggle around you will find the clips holding it in. Pry n…
Popularity: 95
remove the knobs and there are nuts under then to remove. Then take the nuts from the back of it under the dash and the wiring and remove. nice , duh If your stereo is an integrated faceplate unit (as most post-1991s are) there should be four holes on the faceplate, 2 on the left and 2 on the righ…
Popularity: 37
You must have the code which is either in the manual or can be obtained from the dealer with your VIN number, I believe. Other people have said it's also by the tire jack but I haven't looked there. I don't have an owner's manual so the dealer had to look it up on the computer for me. I've had thi…
Popularity: 95
Contact the dealer, There is a certain procedure you have to go through.
Popularity: 41
If the car is like the 1997 model Hyundai Accent (USA, or 1999 Excel from Australia) try this:-1/ Remove the panel under the steering wheel. There should be four bolts - the two at the top are covered with plastic caps. When you have removed the panel, take off the two climate control cables that ru…
Popularity: 138
its easy once you know the secret. The plastic cover around the shifter just pops of if you grab the lower part of it and lift up. Then remove the center ac knob an d remove the screw behind it. Then you can pry the whole center part out startign from the bottom again and pulling outward. remove the…
Popularity: 114
Remove the a/c ducts then the wires and mounting bolts under the dash. Then the knobs on the front and nuts under them then work the rakio out from under the dash.
Popularity: 27
Is it only this station that is coming in poorly? If so it may that the station's signal is weak or located in a place that is far away. The other thing to check.........the antenna cable jack at the back of the radio may be loose.
Popularity: 55
if you don't have the infinty system installing an after market stereo is very simple. just pop off the frame around the stereo (it has the climite controls on it as well) there aren't any screws it just pops out and then there are 4 screws to remove the deck from the frame around it. there is also …
Popularity: 41
%DETAILS% Answer +These are unusual problems. Take it to an electrical expert.
Popularity: 39
It is easy to remove the FM radio. You may have to 1st remove the ashtray. Then using either a L shaped or curved PIC tool pry the plastic frame off which encompasses the radio,and temp controls. Be careful when prying the cover not to dent nor damage the soft dash board around the plastic cover. Yo…
Popularity: 54
Answer Try checking the fuses. If ok, then it is a wiring or electrical prob. You might also want to check your ignition switch. it may not be making contact properly. I found this happening on my1991 cavalier also. If I would twist the ignition like I was going to start it again, but not far e…
Popularity: 35
No there is only one wire for the radio antenna unless you have an extension on it or after market part . But then again I'm not sure if i know what your trying to ask . But that's the best i can do for you with the info I'm getting !
Popularity: 85
You will need to call the dealer and provide the id # If your lucky the previous owner may have written it down in the manuel near the radio section. Mine was.usually the code is the last four numbers of the serial number
Popularity: 54
http://www.impalahq.com/ I would sugest to visit the FCSR site at www.carstereohelp.com, and you will find there instruction for any car Radio/dashboard removal, with nice pictures just for 6 dolars. Very Recomended.   Open both front doors, remove the fuse panel/relay cover panel at top by p…
Popularity: 88
First you have to pull apart the gray console around the radio with any flat thing like a screwdriver, then just unscrew two bolts in the corners of the radio. X. V.   www.installdr.com will tell and show instructions for everything
Popularity: 56
Remove the neg battery cable then the wiring and nuts holding it from the back of the dash. Then remove the knobs and the3 nuts under them and work it out from the back   The easiest way to remove the radio is to remove the ashtray assembly. There are a few small Phillips head screws in the…
Popularity: 37
Answer Hey just had the same problem in my 92 SC2. The radio fuse box is to the left of where the passengers feet would be. The thing is on mine (not sure if its the same with them all) the fuse was labeled "chime" instead of the actual radio fuse. Might want to get a fuse tester and check them all.…
Popularity: 81
you could go to radio shack and get an installation kit for 96' elantra and it is self explanatory.
Popularity: 87
I had a 95 Ford Explorer and all you have to do is to hold the clock button and then click press the bass and treble button.
Popularity: 44
First remove the negative battery cable. Then the lower a/c ducts then the wires and bolts that are holding it in that are under the dash. Then take off the knobs and remove the nuts that are under them and work it out..
Popularity: 30
Typically this is a failure of the headlight switch assembly. See the question about how to replace the headlight switch in a 1991 Cherokee for the answer of how to accomplish.
Popularity: 60
You have to remove the center cluster (with the cigarette lighter, ashtray, and flip-pocket) by way of two screws on each side of the unit, then pulling the unit slightly angled outward toward the shifter. Once this is removed you also must remove the stereo (and the anchoring frame if you purchased…
Popularity: 82
Haynes manual? this club site may be of interest to you http://www.vauxhallownersnetwork.co.uk/
Popularity: 60
Start by lifting the surround around the shifter up by putting a thin blade around the edge and lifting up. Once that is out, undo the screws under the ash tray.The plastic bar above the ash try needs to be pryed out too.Remove the ash tray.now take the air conditioning vents out at the top of the …
Popularity: 62
It's actually pretty easy: 1) Always disconnect the negative batt. terminal before doing electrical work. An 8mm socket should do the trick.2) Open both the driver and the passenger door, the cover marked "Fuse" on either end of the dash board must be removed. They may be a little difficult to pull …
Popularity: 78
%REPLIES% press the set button and use the seek and scan buttons to change time.   Press the volume control knob and hold down. Press the seek button left to set hour, press right to set minutes.   Hold the clock button, and use seek left and right. Left <- (Hours) & Right -&…
Popularity: 49
Contact the dealer.
Popularity: 77
Under the hood, right next to the battery, there is a fusebox. There is a 15A fuse in this fuse box labeled audio.This is the fuse that interrupts the default power signal for the stock radio.Most aftermarket radios rely on an adapter harness that changes the stock wiring to the standard wiring maki…
Popularity: 28
You can remove the radio unit from your 1997 Nova with a flat head screwdriver and a Phillips head screwdriver. You will not need any other tools to complete the task.
Popularity: 34
I don't have an answer but wonder if you have had one yet? There are a series of fasteners under the dash but I don't know if that is what is holding the dash on or not. I am going to find out as soon as I can get some kind of tool to pull them. I don't want to harm the dash. Thanks Joe I don't kn…
Popularity: 69
SOME OF THEM U HOLD THE ON/OFF BUTTON IN THEN PRESS THE PLUS OR MINUS SWITCH-FOR THE CHANNEL.
Popularity: 33
Check the rotor and cap.   Could be bad wires. Deteriorating insulation could have caused the interference and could now be shorting before current reaches the plug. Look at the wires at night or it the dark hood open have someone crank the engine over while its beeing cranked spray wires and…
Popularity: 86
If the radio has both knobs to the left of the radio, then you will pop off the trim that surrounds the radio. Behind this trim you will find the screws that secure the radio. Caution- there may also be a rear support bracket which would require you to crawl up under the dash and unbolt it. The wire…
Popularity: 27
Look in the owner's manual.   You will be relieved to know it is very easy. Locate the Tune button and at the bottome of it there are 2 small buttons, one to the left and the right. When you depress them it will cahne the hour(left) and the right will change the minute. Cathleen
Popularity: 25
Make sure the antennae is connected and good, Then you may try an anti-static kit from radio shack.
Popularity: 46
First disconnet your battery.Carefully pry out the clock out of the middle and there is a screw back there you need to take out ,than two more screw at the bottom of the center cover. Once u take the screws out carefully pull the console out and disconnect the two ac connectors(I had to use a flat-h…
Popularity: 90
Take it to a radio shop.Just replace it with aftermarket. Wiring1985 Cadillac Seville Car Audio Wiring DiagramCar Radio Battery Constant 12v+ Wire: Orange Car Radio Accessory Switched 12v+ Wire: Yellow Car Radio Ground Wire: Black Car Radio Illumination Wire: Gray Car Stereo Dimmer Wire: Brown …
Popularity: 49
Yes this is a complex problem however if you are comfortable with some tools here is a step by step answer for you...Step 1) empty the storage section under the armrest - remove bottom trim plate and remove screws - Pull out cup holder insert and remove 3 screws 2 down in the middle and 1 at an angl…
Popularity: 66
I heard that you get the vin# off your car & take it to the GM dealer and they should give you the anti theft code for free, hope it works, I'm haveing a problem of my own.
Popularity: 65
%REPLIES% Answer You can only get that info from the dealer. Answer the only way to get that is to get the code off the side of the radio or sometimes they are in the glove box it should be a four number code
Popularity: 31
Using the scan button while pressing the #7 and #8 station preset buttons. I believe the radio needs to be turned off.   There ar no #7 and #8 preset buttons, only up to #6.   Use the radio preset station buttons, look under the last few numbers, you'll see a small black H for hours, a…
Popularity: 65
There is a website carstereohelp.net that can help you with replacing your radio. They give you step by step usually with pictures. Good Luck
Popularity: 43
Unfortunately, it sounds as if one of the bulbs are burnt out inside the instrument cluster. You are going to need to get a book to help guide you in repairing this problem. You can buy a book at an auto parts store, or you can go to the Library and take a notepad and pencil with you.
Popularity: 24
What you need to do is turn the car on so that the radio comes on. While the radio is on, push straight in on the volume knob and then use the seek button to set the time. The left arrow sets the hours and the right arrow sets the minutes.Pretty close: Actually turned out to be the "tune" rocker but…
Popularity: 35
On an M reg 106 1.5D it is surprisingly easy. The odd shaped Peugeot radio fits in a standard radio slot. To be honest the easiest thing to do it take it to a Peugeot dealer and ask them nicely to remove it - it will take them thirty seconds using the special tool. Alternatively the Haynes manual te…
Popularity: 66
You need to go to a sound shop and buy an adapter that will allow your radio to be plugged into the car's wiring harness. You will also need to ask them which ground wire to cut, so you don't blow out the dimmer switch for your dash lights.
Popularity: 32
Check the fuse. If it is a factory radio , It would be best to take it to a dealer and get then to put in the security code for it : Remember, this car has two fuses that operate the radio, one behind the driver kick panel, the other in the fusebox under the hood. When the car was new, the 5 di…
Popularity: 65
Answer I too would like to know the answer as my 2001 Chevy Impala done the same thing. Tire pressure monitor will not reset through the radio menu. ____ My 02 was doing the same thing. No option in the radio menu. I ended up having to disco the battery for a few seconds to reset the memory. Wo…
Popularity: 51
You don't remove the dash. You remove the part of the dash that surrounds the radio, thus giving you access to the radio.
Popularity: 32
First, remove the two dash screws located above the steering wheel assembly. The rest of the dash unclips. Disconnect any electrical connectors and remove the dash. This whole process should only take about 5 minutes. Once the dash is removed, the stereo and the tray below it are held in by four scr…
Popularity: 22
Hold clock button and volume increase or decrease to index hours of minutes.
Popularity: 22
1) Open the glove box and remove 5 screws. I think 9/32" screws.2) Remove side panels from driver side dash and passengers side dash, and extract 1 screw from each side.3) Remove 1 Phillips head screw at top center of air vent.4) Extract 2 screws under vent panel, carefully remove top dash.5) Extrac…
Popularity: 22