0
Chevrolet
A brand of vehicle, Chevrolet or Chevy was produced by General Motors Company (GM). The car was named after Louis Chevrolet and was set up to sell a variety of mainstream vehicles to compete with Model T by Henry Ford.
6,429 Questions
What do you do if you lose the keys to your car?
go to dealer with title and identification and they can make a new key for you
What are the torque settings for flex plate bolts on a smallblock Chevy?
Crankshaft to flexplate: 50-60 lb-ft Flexplate to torque converter: 45 lb-ft Use Grade 8 or better at both locations.
What is the best small block Chevy intake manifolds?
The performer is a pretty good one for street use. Weind used to make one called the Team G, and the torker, second design, all work well for a street car. Race only, I swear by the Holley Strip dominator. They make 2. The taller version, gives less low end, and more top end, if launching is a problem. Edelbroc, makes the Victor Jr., with a tall and short version, as well. It is my second choice. If you are that into it, your cylinder head maker would be a good person to discuss this with, as well as your camshaft advisor. The intake has to match the power band of the motor.
What is the largest tire and rim will fit on an 1986 Chevy sportvan?
Hi, will 18" 5 lug 2011 camaro wheels fit a 1995 15" 5x5 chevy sportvan van hub?
Where is the thermostat on a Chevy 454?
It should be inside the "water neck"...which usually bolts into the top of the intake manifold. You will have to un-bolt the water neck and you'll find it inside that.
How do you change rear seal on small block 400 Chevy?
You have to take the oil pan off, then the oil pump, then the rear main cap. They make a tool called a chinease finger to get the upper half out, and the new one in around the crankshaft.
Who invented the automobile airconditioner?
1939 Air conditioning offered as an option in a Packard automobile
It has no meaning other than it was the last name of the founder of the company Louis Chevrolet.
What year was the 5.7 Chevy small block made?
The 5.7 Liter (350 Cu In) small block Chevy was produced from 1967-2003
How do you set timing marks on a 1996 Chevrolet 5.7 vortec?
If you are asking about the timing chain, Here it is, The crank gear dot should be stright up that is 12 o-clock, that means #1 piston is at TDC on the compression stroke. ( JUST FIRED ) The cam gear dot should be stright down and in a stright line with the crank gear dot, that means the intake and exhaust valves are closed and on the compression stroke. Install both gears with out chain first to aline dots up. Then remove cam gear only and install chain, put gear and chain back on and make sure the dots are lined up over top of each other. Your done.
How do you start a car that has not been started for two years?
First, get all of the old fuel out, then put a couple gallons of new fuel in and change the fuel filter.
Change the oil and filter, substituting a can of your favorite engine cleaner for 1 quart of oil. (follow the directions on the can of cleaner)
Then, use a jump start or whatever is necessary and spray a little starting fluid as a helper tries to start the engine.
Next, put a can of high quality injector cleaner into the tank when you fill it then put some miles on it.
Don't go very far from home. It's likely to start having problems sometime during the first few thousand miles.
Change the oil after a couple hundred miles.
Good luck. Recognize that all of the rubber parts will be likely to fail soon, so be watching for engine and transmission seal failure as well as tire and other rubber part failure.
Can you put a 1998 Chevy transmission in a 1997 Chevy 1500?
From truck to truck, yeah, they are the same.
It is a Belaire so it should have the 235. The 235 firing order is 1-5-3-6-2-4 Spark plug gap - .035 Uses AC 46-5 Idle speed Manual Trans 475 rpm / A/T 425 Click the link for more info.
How do you remove speaker covers on a 2006 Chevy 2500HD?
if you pull it hard enough it will un bend the tabs and come out, but to put them back on you have to take the door panel off and bend the tabs sideways to secure the speaker cover
Where is the PCV valve on a 1964 Chevy 327 engine?
it is on the valve cover. tubed over to the air cleaner
Where can I get a Diagram showing how to install a serpentine belt on a 1990 Chevy 1500 pickup?
You can go to Autozone.com. They have online manuals you can view for free, you just have to enter the make and model of the vehicle you are inquiring about
You can go to Autozone.com. They have online manuals you can view for free, you just have to enter the make and model of the vehicle you are inquiring about
They only have generic charts just showing pulleys and lines with no parts to relate to, and not in any way similar to the relationship of the parts on the engine. At least that was the case with my '90 Suburban. Just single lines and simple circles - nothing more
It was impossible to relate the cryptic diagrams to the real world and I ain't no dumy.
