0
Acura CL
Acura CL is a car model produced by Honda’s Acura brand from 1997 to 1999 and from 2001 to 2003. The CL was the first vehicle from the Acura series to be built in the US.
467 Questions
Where is the water pump on an Acura cl?
The water pump on the CL models 2001-2003 is located at the top left of the engine. It has a dedicated Pulley and belt system. The Pulley and Belt are easily visible on the top left hand side of the engine when viewing the car from the front. Honda recomends changing timing belt and water pump every 105K.
What does flashing d4 and check engine mean on a 97 Acura CL?
Transmission problem. Take it to a professional for repair.
How do you program keyless remote for 1997 Acura CL?
First, make sure you have the correct remote.
FCC: E4EG8D-444H-A.
Also, do you have memory seats in your MDX? If so, make sure your remote says MEM 1 or MEM 2 on back.
For programming:
Do steps 1 - 12 on the same remote (AT TIME OF PROGRAMMING BOTH REMOTES MUST BE PRESENT SINCE THEY WILL NOW BOTH HAVE TO BE REPROGRAMMED.) The following steps 1-12 are done on a single remote step 10 is done on all remotes to be programmed up to 4 can be programmed
1) get into the car shut the doors (including trunk or tailgate) and make sure they are unlocked
2) turn on the ignition (number II position)(do not turn on the engine just the ignition til the dash lights come on) (LISTEN FOR A QUIET CLICK)
3) press the lock button on remote (turn to off) (Do not remove key)
4) quickly turn on the ignition (do not turn on the car just the ignition) (LISTEN FOR A QUIET CLICK)
5) press the lock button on remote (turn to off )
6) quickly turn on the ignition (do not turn on the car just the ignition) (LISTEN FOR A QUIET CLICK)
7) press the lock button on remote (turn to off )
8) quickly turn on the ignition (do not turn on the car just the ignition) (LISTEN FOR A QUIET CLICK)
9) press the lock button on the remote
the locks should cycle to indicate that programming mode was entered successfully
10) press the LOCK button on each remote you want programmed and the door locks should cycle again to confirm programming. THIS STEP NEEDS TO BE DONE FOR EACH REMOTE
11) turn off the car fully and remove key.
12) try locking/unlocking with remote to test
The important thing is to quickly turn the ignition off then on after hearing the click and pressing the lock button. If you hear the click in the off position, you waited too long and must start over.
This does work, I just used it to program my 2004 MDX, 10 minutes ago. Although it took a couple tries.
How do you replace the headlight bulb located on a 1998 Acura CL?
If it is your low beam buy 9006 bulb. If it is your high beam buy 9005 bulb. Under the hood on left front side you will notice the back of the headlight assembly. In the center will be the bulb, turn it to the left or the right and take out...replacement is reverse from removal with a new bulb making sure you do not touch the new bulbs glass. The right side is the same accept for a plastic cover near air filter, use your discretion on taking off this cover it is not hard and the procedure is the same as the left side of the car.
What is the code to unlock radio 1999 Acura CL?
All Acura's have Radio codes. You will need the code if the power has been disconnected from your battery. It is a five digit code that can normally be found either in your drivers manual or on a business card size card that reads Acura Radio Code. If you enter the radio code incorrect three times it will lock you out of the radio and you will have to disconnect the battery to start the process again. Radio Codes are specific to your VIN number, a dealer CAN NOT "create" one for you. If the originating dealer put the code in the American Honda Motor Co system then your local dealer will be able to assist you. Call them with your VIN Number and have proof of ownership ready, some dealers will ask you for it. If your radio code is not in the American Honda system then the ONLY way to get the code is to remove the radio as it is on a sticker on the back of the radio head. This information also applies to Navigation units and all models, years and makes of Acura.
Read more: How_do_you_enter_the_radio_code_for_a_1997_acura_cl
A 1997 Acura CL in good condition sells for approximately $2,000.
How do you change the bulb on the brake light on an Acura CL 3.0?
No model year given... Here's the general Acura CL brake light bulb lamp replacement procedure: Purchase the correct replacement brake light bulb(s) first, before disassembling the vehicle. See sources and related links below for replacement brake light bulb information. Then consult your owner's manual for the replacement procedure. As simple as it sounds, the owner's manual is the best place to start for brake light bulb lamp replacement instructions and illustrations. You may want to consider replacing both left and right at the same time in order to keep brightness and color equal (optional).
How do you remove the oil pan on a 1997 Acura CL?
Hello,
The following is a procedure on removing and installing the oil pan on a 1997 Acura CL 3.0:
1. Raise and safely support the vehicle
2. Drain the engine oil into a suitable container.
3. Remove the exhaust pipe if necessary.
4. Unfasten the oil pan mounting bolts, then remove the oil pan.
5. Clean the sealing surface on the engine and oil pan flange.
6. Apply a bead of sealant to the oil pan flange and install the oil pan. Tighten the bolts to 104 inch lbs. (12 Nm)
7. If removed, install the exhaust pipe.
8. Add the correct amount of engine oil to the crankcase.
9. Start the engine and check for leaks.
I hope this helps you out!
How do you remove intake on 97 acura 3.0 cl?
Remove the clamp by the throttle body then remove all hoses that connect to stock intake then remove all 4 screws on top of filter remove filter n filter box then pull box out n remove what ever screws n bolts u c
To tune up an Acura CL, start by replacing the engine oil and oil filter, ensuring the engine runs smoothly. Check and replace the air filter and spark plugs if needed, as these can improve performance and fuel efficiency. Additionally, inspect the ignition system, including wires and coils, and ensure the tires are properly inflated and aligned for optimal handling. Finally, check fluid levels for the transmission, brakes, and coolant to maintain overall vehicle health.
How do you clean the idle air control valve on a 99 Acura 3.0cl?
IDLE AIR CONTROL VALVE (IAC)
Definition: An electrically-operated valve which allows air to bypass the throttle plate in a fuel injected engine to regulate engine idle speed.
Buy it new; it doesn't even pay to clean it. It works half the times. But it will go bad eventually…
Where is the Bose amp located on a 1998 Acura CL?
In a 1998 Acura CL, the Bose amplifier is typically located in the trunk on the driver's side, mounted on the rear wall. To access it, you may need to remove some trim panels or carpeting. It's usually situated near the rear speaker assembly, making it relatively easy to spot once the trunk area is cleared.
How much does a diagnostic test cost for Acura CL 99?
Go to auto zone(free) if its just an engine diagnostic (engine light...etc.) (plug might be behind ashtray/earlier models)
How do you reset the check engine light on Acura 3.0 cl 1998?
I have a'97 Acura 2.2 CL, so resetting the "Check Engine" may be different for your vehicle than for our's. On our vehicle there is a small window or slot in the instrument panel. You just slide your ignition key through this slot, and the light resets. Hope this helps.
Where is the dipstick for the transmission fluid on a Acura CL?
It's on the drivers side of the engine. The dipstick has a yellow loop handle.
