What is the difference between pipe earthing and plate earthing?
Assuming your reference to "earthing" is grounding (Grounding Electrode Conductor), a pipe is, as it sounds, a pipe (i.e. water pipe). A plate would be, as it sounds, a square (or rectangular) copper plate which would be buried in the ground.
Why electricity does not flow through iron core of transformer?
It does. We call this current, or currents, 'eddy currents', and they are minimised by using laminated cores.
Can you use capacitor as a memory device?
Yes you can, in fact I almost guaruntee you did to write the question - the RAM in your computer is likely DRAM, or dynamic random access memory, which uses capacitors to store bits. The problem with using capacitors is there is always some leakage current flow, which results in slowly draining the capacitor's voltage. To prevent the loss of data, DRAM continuously "refreshes" itself by measuring whether the capacitor is charge or not, and fully charging it if it is considered a logical '1'. The capacitor's voltage will again slowly drain off until the next refresh cycle.
The main benefit of this type of memory over more static, gate based memory is it is very cheap, and easy to manufacture.
A transformer is a device used to increase or decrease dc voltage?
The answer below this is not correct, a transformer can only be used on AC not DC. So the statement, "A transformer is a device used to increase or decrease DC voltage" is false
The above comment relates to an entry which was obviously deleted.
However, the above comment is also false. The ignition coil in of a petrol engine is a transformer, a pulse transformer. It's d.c. which passes through the primary, not a.c.
<<>>
A: this is a passive component as opposed to a device that is active answer is yes it does that but more importantly it isolates and match in/out impedance's
Difference between natural frequency and resonance frequency?
In natural frequencies the output of the system will be less than the maximum level. In the resonance frequency the output of the system will be the maximum level.
What is the voltage across the load R when the switch is ON?
It's the product of the resistance of that resistive load and the current passing through it.
What the factors that affect the preferential discharge of ions at the anode and the cathode?
how am i suposed to answer it if i am asking wat it is
What is the specific voltage drop in a 95MM three core armoured cable?
Need to know the wire size of the core conductors.
Would upgrading your electrical service stop tripping breakers?
=== === Not exactly. Breakers trip because the current exceeds the rating of that breaker. In other words....you're plugging too much into that circuit. And the wire can only safely handle a certain amount of current; so you can't just put a bigger breaker in. === === <><><> (LIFE SAFETY WARNING! [disclaimer]
Electricity is dangerous!
You can be injured or killed!
Improper installations can cause fire, injury and death!
The only time I would expect "upgrading" your service would help you to stop tripping breakers was if it was the main breaker that was tripping, and that because of overload [high current]!
It is possible that the panel is poorly maintained and the breakers do not connect to the busbar snugly, allowing a voltage drop at the connection point. This would generate heat at the connection which would contribute to the breaker tripping if it has a thermal trip as well as a magnetic element. It would also contribute to lowered voltage at the intended load, which could cause higher current draw in some cases [motors]
On the other hand, I have found that some unscrupulous tradesmen will use the opportunity to sell a big job because they need the work, rather than fix a simple problem.
I recently had a service call where the people complained that "everything goes out all over." They could have been sold a new service by someone, even though theirs wasn't that old ... but all they needed was to have additional breakers installed.
Somebody had put three circuits into one breaker and two each into two others, so they had three breakers instead of seven.
The usual real solution is to run a new line for new receptacles to the point of high demand and leave the rest of the wiring alone. Home handymen and many remodelers who do their own electrical work often just dump anything they add onto any existing circuit. <><><>
As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.
Before you do any work yourself,
on electrical circuits, equipment or appliances,
always use a test meter to ensure the circuit is, in fact, de-energized.
IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
What is the electric usage for the typical chlorine generator?
Salt Generators can run on 110/120 volts or 220/240 volts. They have a transformer that steps the current down to 12 volts so the electrical usage is very minimal. None of the manufactures even mention power usage because it is so low; your pool pump is going to draw 100 times more power than a salt generator. So if you are thinking of installing a salt generator don't even make this a consideration because if it cost you $10 a season I would be shocked (no pun intended).
Surface wiring is wiring that is enclosed in some kind of containment and surface fixed. For example if you installed a conduit containment system to supply a socket this is screwed to the walls with "saddles" and a mounting block is used to protrude the socket off the wall to take the conduit. This is surface wiring as opposed to concealed wiring which is encased in the fabric of the wall and all you see is the socket.
How the differentiation of the signal amplifies the noise?
any signal, be it be noise is composed of sinusoids...so when one differentiates sinWt with respect to time it becomes WcosWt ...hence the signal gets multiplied by W..
How many ohms is a low resistance?
This is relative to the purpose or application. 1 mega ohm may be considered "low resistance" when testing insulation levels; when testing a cable, 1 ohm may be too much. When testing substation ground grids, I believe 1 ohm is the maximum allowable value in some countries.
What is the name of conductor which obeys ohm's law?
Everything obeys Ohm's law - antennas, cables, transformers, integrated circuits, etc.
AnswerIt is not true that 'everything' obeys Ohm's Law. For a device to obey Ohm's Law, the ratio of voltage to current MUST remain constant for variations in voltage. This is why Ohm's Law is a law of constant proportionality.Why does a battery give DC and Not AC?
The voltage between the two electrodes of the battery depends on the redox reactions going on at the electrodes. The overall reactions stay the same, so the electromotive force stays about the same too. The electromotive force is however dependent on the concentration of the reactants the electrolyte, and the voltage at the outside of the battery depends on the internal resistance of the battery as well, which can be much higher when the battery is used.
A battery is energy stored in a chemical way. When "converted" into electricity, the chemical looses power, either going from a base of very low PH to neutral or from a base of very high PH to neutral.
A fresh battery gives out a "high" voltage and slowly as it is discharges, the electrolyte inside will reach a PH of 7 (neutral) and voltage drops accordingly.
The voltage can not drop below zero, as the electrolyte has lost all its power when it reaches a PH of 7.
Chemical reactions work only one way, reaching PH Neutral as its ultimate goal, where as in AC one have mechanical movement of wire in a magnetic field.
No movement, no electricity. When the wire moves in a magnetic field it produces electricity, but only as long as the magnetic field constantly changes from North to South and back to North again. It is this that creates AC or alternating current, hence the Alternating magnetic poles.
Can you turn a multi-tap ballast into a step down transformer?
A mulit tap ballast is in fact an auto transformer.
How much power does a DC to AC inverter use when not used?
One 150 watt inverter reports 0.2 Amps (=approx 2.4watts)
Another inverter (180 watts?) reported 0.4 Amps
If you find a fairly complete spec sheet, it may tell you the Amps or Watts that it uses under "No Load".
I'm the originator of the question, and I discovered the "additional" specs.
What is open circuit and short circuit?
Consider two points (A and B) in an electric circuit. An open circuit between A and B means there is no electrical connection between A and B. A short circuit between A and B means there is an electrical connection between A and B.
Did you mean e. coli? If so then:
A bacillus (Escherichia coli) normally found in the human gastrointestinal tract and existing as numerous strains, some of which are responsible for diarrheal diseases. Other strains have been used experimentally in molecular Biology.
Read more: escherichia-coli
What is difference between capacitor and super capacitor?
Super capacitor have high capacitance compare to normal capacitor. Super capacitor use two layer of dielectric medium whereas in normal capacitor single medium dielectric.
Because of this super capacitor use as alternate power source for RTC when computer is off.
Arc. It's where electrical resistance is used to create the heat for the welding process.
Who invented the Bose Acoustic Wave system?
The man who gave his name to the company and stereo music in a small package to the planet goes by the name of Amar Bose. Apparently he did have help from others but his name is best known through the world of high quality sound
High-voltage transmission line conductors are 'bundled' -that is, each 'line' comprises two or more conductors, rather than a single conductor, suspended from each insulator chain.
The reason for bundling is to reduce the intensity of the electric field on the surface of the conductors (the same field is shared between the surfaces of several, rather than just one, conductors), which would otherwise result in a breakdown of the insulating property of the air immediately surrounding a single conductor.
In the UK, 400-kV transmission lines use a bundle of four conductors per line, and 275-kV transmission lines use a bundle of two.
How can calculate HT cable size for 500mva transformer rating and voltage 11kv?
500Mw at 11kv works out to 45000 a
a bit big for any wire manufactured on this planet
suggest you go to a more practical voltage like 132,000V
AnswerSince we are inevitably talking about a three-phase transformer, the line current is determined from
IL= rated apparent power / (1.732 x UL) = (500 x 106) / 1.732 x 11 x 103)
...which works out at 26 244 A which, as the original answer suggests, is not a practical value for this combination.