Electronics Engineering

It should me stamped on the information plate.

If this is not on it, then there will be the running current stamped on the plate. Multiply this by the supply voltage to find the power in watts. Take the horsepower of the motor and multiply it by 746. There are 746 watts in 1 HP. It is also the same for single phase motors.

astable network means it has only one stable state.so the circuit need trigger input to change to another stage and it automatically changes to the previous stage when the process completed with the use of the capacitor.

ohms=amps/volts

Amps= volts/ohms

Volts = Amps*Ohms

Historically, transistor-transistor logic (TTL) voltage levels have been 5.0 volts, with a high being any voltage above about 3.5 volts and a low being any voltage below about 1.5 volts, with lots of variations on the high/low cutoffs from part to part. Since about 2001, however, most processors have been using low-voltage TTL (LVTTL), which has a nominal voltage of 3.3 volts (approx >2.2 volts for high and approx < 1.2 volts for low). Hence, many parts advertised as "TTL" today actually work at 3.3 volts rather than 5.0 volts.

take it to your near autozone,they started making some aftermarket products,if they don't have one for your vehicle take it to a Chrysler dealership and they will match one up but if they have to reprogram it, it will cost extra along with the keyless entry,sometimes they don't have to reprogram them.

If I remember correctly, the definition of "modulation" is a "change in amplitude or frequency".

electronics engineering is the branch of engineering which deals with the flow of current in a semiconductor devices/components.

Semiconductor devices/components are those element which made from semiconductors like silicon germanium GaAs and other material.

they are widely using in current generation.

By talking to your Cable provider.

Rotational motion is motion which emulates that of the minute hand of a clock. Oscillating motion is motion which emulates that of the pendulum.

dynamo

copper losses are power losses due to flow of current in the wires or resistances,if the resistance is R, current is I then copper losses are I2R.

for a 3-phase system; copper losses are same but for a single line, total losses are 3I2R.

RTD - Resistence temperature detector

Thermistor

Pyrometer

Thermometer

The lookup table in a microprocessor is a system that helps replace the runtime computations. It replaces them with an easier index operation.

A RC circuit is a simple filtering circuit. The impedance of R will stay the same across the frequency band. The impedance of C will vary according to 1/jwC (j = i = imaginary number, w = omega/frequency in radians, C = capacitance in Farads). As frequency varies from low frequency to high frequency, an increasingly smaller amount of the signal voltage will "drop" across the capacitor. This is known as a first order (one reactive element, the capacitor) low pass filter if the desired signal is measured across the capacitor. If measured across the resistor, this would be a first order high pass filter.

Edit: if you are talking about ESR (equivalent serires resistance), it is a parasitic component inside a capacitor. Theoretically, you don't want it but it's there.

WE USE Preset in a circuit to work it perfectly by adjusting a value & we cant change the value of preset after its working.

Potentiometer can be used to vary from (0-n)

Current is proportional to the potential difference and inversely proportional to resistance.

Ohm's law: Current equals voltage divided by resistance

A magnetic field around the wire.

A: It is an IC which contain an led which will couple the input to another device within the package it can be a transistor a triac scr and so forth. is main purpose in application is to isolate the source from the output.

shunt field winding have more resistance than series field winding

************sai ganesh ************269*******

A: Sure by adding or subtracting from different inputs or scaling with different value of resistors

MOSFET can be used in enhancement mode

A discrete component is one where the package contains only one circuit element. The opposite is an "integrated circuit" (aka a "silicon chip" or "chip") where a package contains many circuit elements.

It's not that "discrete" is a type of resistor, it's that a resistor is a type of discrete component.

Go back to your teacher/lecturer/tutor and check the question..

My experience shows that it's the *opposite* way around.