0
GMC Yukon
The GMC Yukon is a full-size sport utility vehicle manufactured by General Motors from 1992 to the present. The car is available as either a two-door or a four-door model. It features a front engine and a rear/four-wheel drive.
1,653 Questions
What is the wheel base of the 2001 GMC Yukon?
The 2001 GMC Yukon has a 9 ft. 8 in. (116 in.) wheel base.
What kind of fuel does the 2006 GMC Yukon-XL use?
The 2006 GMC Yukon-XL runs on flex-fuel (unleaded/E85).
Why is the service stability message on in your 2005 GM Yukon?
Yes there is health travel insurance available. Call you insurance company and explain your situation and they will make sure you have the proper health insurance.
How do you install an inside door handle for a 1999 GMC Yukon?
I just did this for the 2nd time.
Remove the 2 screws in the armrest.
Remove the triangular trim piece at the front bottom corner of the window.
Remove the bezel (trim piece around the door handle unit (this is tough) there are 3 tabs that you must slide something flat in and push down to get this off.
Edited for clarity: The bezel IS difficult to get off. The three tabs mentioned are positioned approximately @ 12:00, 9:00, and 6:00- nothing @ 3:00. I wished I'd know that going in- I broke my bezel too. Also, a more accurate description of what you have to do to get it to release is; from the outside of each of the positions, slide the thin, flat tool in from the edges towards the center of the bezel while slightly pushing from the outside over the particular position. When it releases, then lift away.
I broke the first one ($21 at dealer)
Sometimes it's easier to have the window rolled down all the way prior to the next steps- Then before actually working on the door lock, roll the window back up before disconnecting the control power to the window. Otherwise the lowered window may be in your way.
The panel itself is held on by a series of plastic "screws" that are inserted into a plastic receiver.
Carefully pry each one loose. Using similar flat tool.
Lift the door panel up (it is "hanging" on the lip of the door).
Your window and door lock control module will be hanging by wires this is OK.
Be careful not to stress these wires too much- or you may be back trying to fix your window/ door lock module!!!
Slide the door handle unit forward and it will come loose.
There are 2 connecting rods attached to the back of the unit, 1 for the lock, the other for the handle (that opens the door). I'm sure this is the part that is broken on yours (2nd time mine has).
Buy a new unit ( I got the 1st at the dealer for $50 2nd at Auto zone for $21)
Disconnect the two rods using a pair of needle nose pliars (they will just unsnap)
Install new unit lining up the holes and pulling it back (towards the rear) it will lock in place.
Make sure you hook up the door light, towards the back of the door, re-install panel. and bezel.
Mkgwiki says:
I was trying to find an answer on how to change the OUTSIDE door handle & lock when I found this answer. I found it VERY helpful. I took the liberty of adding some minor suggestions above- hope the original author doesn't mind.
I am going to add the additional info here for completing that task.
After completing all of the disassembly above, with the window UP, if the clear plastic is still intact, carefully peal it back from the outside edge of the door (to gain access to the interior of the door).
There is a round hole towards the top of the panel (opposite of where the outside handle is). This is an access hole to put a socket & extention or nutdriver (10mm) in to remove a screw. It is identical to the one in the door jamb- which is the 2nd of two screws holding the outer handle in place. To save yourself some grief & time from looking for a fallen screw, if your arms are small enough, and long enough, put your arm in the lower hole in the panel and reach up towards the back side of the handle mechanism and to remove & install the inner screw with that hand.
Once the outside handle is loose, but still attached by the operating rods, you can carefully remove the retaining clip on the handle operating rod and remove the rod from the hole.
Then carefully rotate the still attached handle and look under the lock mechanism to find the spring loaded lock release (in the slot closest to the rod). Take a small screwdriver and push that tab in and the lock tumbler assembly will slide right out. Easy pezy. (no need to remove lock tumbler rod or clip!).
Take care to retrieve rubber seal in old tumbler housing and re-insert in new replacement handle.
The new handle should come with a retainer clip already in place for the operating rod, so all you have to do is slide the end of the operating rod into the hole til it clicks in place on the clip.
Carefully re-install handle assembly back in hole, install screws and re-assemble door parts in reverse order.
Hope this helps.
Where is fill plug in a manual transmission in 1995 Jeep Wrangler?
Most filler plugs on transmissions and transfer cases are or 2 types; both are threaded plugs; with either a hollow square hole in it (traditionally 3/8") and you remove it with a 3/8" ratchet wrench. It's easier if you use a 3" extension for this job. The other is the reverse, it has a 3/8" square sticking out you turn with a wrench.
Some newer vehicles might use a rubber plug you pry out with a tool like a screw driver. while filling stick your finger in there periodically to ck the fill, stop when your finger is wet. Yes, curve your finger down when in the hole; then re-install the plug and go wash your hands.
How many horsepower does the engine in the 2004 GMC Yukon have?
The 2004 GMC Yukon's engine produces 285 hp @ 5600 rpm.
How do you find out why the bAttery keeps draining?
I had the same problem on my denaly it is a module in the dash for the heather. even if you turn the key off it is still on
What is the oil capacity of a 1998 gmc Yukon with a 5.7 liter engine?
5 and a half quarts including the filter
How do you program the garage door opener on a 2001 expedition?
http://www.homelink.com/home/home.tml It doesn't automatically direct you to the specific video for your truck simply follow the instructions on the homepage and choose "Programing Home Link" from the top menu Step 1, Choose a process Step 2, Choose your vehicle Step 3, Choose your garage door opener.
What size wipers do you need for a 2003 gmc Yukon?
The 2003 GMC Yukon takes 22" on both sides front and 16" rear replacement windshield wiper blades. Note, when buying wipers be sure to always lookup your vehicle make, model and year in the application guide book at the store. Also, see sources and related links below.
How do you program a Marantec Garage Door opener on a 2010 Yukon?
It may not be compatible, I believe GM is using their own universal remote system, not the "homelink" system, Marantec motors are only compatible with "homelink". You may be able to add an external module to the Marantec motor unit for the car remote to be programmable.
For any escalade after 2006, it has a lear vs homelink. Even though there is a button on the Marantec garage door opener motor head with a P on it, this does not program the button. I just got off the phone with Lear, 866-572-2728, and as soon as I told them I had a 2007 escalade and a marantec opener, they said they would ship me a conversion module that plugs into an outlet and hooks up to terminal 3&4 on the opener. She said this would allow me to program my escalade homelink / lear button. Can't wait to get it in the mail and try it to see if it works!
What kind of fuel does the 2005 GMC Yukon-XL use?
The 2005 GMC Yukon-XL runs on flex-fuel (unleaded/E85).
How do you turn off gmc warning lights?
if you cant figure out what the warning is for, you can go in the fuse box of your vehicle and you can take out each one until you find the one that controls the warning lights
What is the angle of approach of the 2006 GMC Yukon-XL?
The 2006 GMC Yukon-XL has a 25 degrees angle of approach.
How many gallons does the gas tank in the 2007 GMC Yukon hold?
The gas tank on the 2007 GMC Yukon holds 26 gal..
Where ia the Fuel pump relay on a 2003 gmc Yukon XL?
The Fuel Pump relay on this vehicle is located in the under the hood fuse block. It is labeled "F/pump" or something like that. It is next to "Prime". It is not in the fuel tank. It is a relay, not a fuse.
How do you disable auto sensing wipers?
Theer is probably a fuse for "wipers" in the fuse box or there is probably a plug that goes into your wiper motor; pull that plug and no wipers! If you want to disable only the auto sensing wipers part(what ever that is) Go buy a Haynes Auto Repair manual for your car. Maybe it's in there.
How do you change the battery of a 2003 Yukon Denali?
make sure your car is off. unscrew the battery that is no longer preforming its batterical functions. replace used battery with one that is new. stop asking dumb questions.
What is the firing order for a GMC 1992 Yukon?
1-8-4-3-6-5-7-2. It's been the same for all small-block Chevys since 1955.
You want to remove the door chime, it's under the dash and is the largest rectangular plug in box of the elect. panel to the left of the brake pedal. Pull the entire retangular component out of the panel, the chime will stop if you get the right one. Or with a bright light you should be able to read "Chime" next to the now empty slot for the removed piece. I removed the center fuse which was for the "DEFOG". I have like four other plugs with several wires coming out of them and they are all the same size. I am looking at the manuel and none of them say "Chime". Please help
Does the 2014 GMC Yukon-XL include free maintenance?
The 2014 GMC Yukon-XL has free maintenance for 2 yr./ 24000 mi..
How many o2 sensors are on a 2002 gmc Yukon XL?
there are 4 , 1 on each exhaust manifold just off each head , these are the 2 that signal how the engine is running fuel wise , example lean or rich , the other 2 are behind each converter to signal how they are performing
