• 
• 1 answer

Hook your purple wire to the red and hook the light green to the ground when out of the car for 4 24hours

• 
• 1 answer

ON MOST KENWOOD CD PLAYERS YOU CAN ENTER THE CODE WITH THE REMOTE USING THE NUMBERS LIKE A TELEPHONE 2 IS FOR A,B,C 3 IS FOR D,E,F ETC. THERE IS A UNIVERSAL KENWOOD CODE THAT IS "KCAR"

• 
• 1 answer

www.mkiv.com and http://www.97supraturbo.com/index.html both have manuals including the wiring diagrams.

• 
• 1 answer

This is the correct color combo for my '92 Storm Gsi LR+ RR+ | clip|IGN LF+ RF+ ----------------------------------- | X X X X X X X | | X X X X X X X | ----------------------------------- LR- RR- gnd l BAT LF- RF- l illum. clip-the release clip LR--Left Rear RR--Right Rear LF--Left Front RF--Right Front IGN--Ignition/power wire--Red BAT--Memory wire--Orange gnd--Ground wire--Black Illumination--Yellow OR This Constant 12V+ Red Switched 12V+ Orange/Yellow Ground Black Illumination Red/Green Dimmer Green/Red Antenna Driver's Pillar Front Speakers 6 1/2" Doors Left Front (+) Orange Left Front (-) Black/orange Right Front (+) Gray Right Front (-) Green/gray Rear Speakers 4" Tail Gate Left Rear (+) Yellow Left Rear (-) Blue/yellow Right Rear (+) White Right Rear (-) Red/white (1) Yellow - Left rear speaker positive (2) White - Right rear speaker positive 3 Red with green stripe - not used 4 Orange with yellow stripe - 12v switched (5) Orange - Left front speaker positive (6) Grey - Right front speaker positive (7) Green - Right front speaker negative (8) Black with orange stripe - Left front speaker negative 9 Red - Constant 12v 10 Green with red stripe - Illumination 11 Black - Ground (12) Red with white stripe - Right rear speaker negative (13) Blue with yellow stripe -Left rear speaker negative

• 
• 1 answer

I have been told by comparing the rear terminal pins (faceplate rear) on a couple of the Aiwa faceplates that at least some are IDENTICAL in that regard and probably are interchangeable on their assigned decks.

• 
• 1 answer

2006

• 
• 1 answer

Yes you can. You need to buy an inline convertor that takes the speaker output from the back of the head unit and turns them into RCA outputs. Then you need to find any wire that powers up when the car is on and off when the car is off. Splice into that wire from the Remote turn on wire. The rest is a simple.

• 
• 1 answer

If you go to the Sears parts web site, which is www3.sears.com, put in your model number, it will show you on the following pages all the parts listings including diagrams for the whole mower, including the wiring diagram. Good Luck!!

• 
• 1 answer

I know that in my 1995 s-10 ext. cab I have: 4x6 on the dash
61/2 in the doors
4x10 in the rear pillars Charlie in N.Y.

• 
• 1 answer

• 
• 1 answer

either a corroded or otherwise poor connection or the starter is pulling too much current

• 
• 1 answer

http://www.bipster.zapto.org/Fun_Stuff/How-To/KDC-MP8017/default.htm

• 
• 1 answer

* Use the SRC button to put the radio into STANDBY mode. Screen should show STANDBY. * Press and hold Menu button for two seconds. * Use the joystick control to scroll up or down until you see DEMO ON.

* Press the joystick in for two or three seconds. Screen should show DEMO OFF.

The manual says to push the joystick left or right, but that is incorrect.

• 
• 1 answer

Two words . . . E-bay!

• 
• 1 answer

http://www.eautorepair.net/ t ain't free but it has what you need 10 buks for a week

• 
• 1 answer

The password is KCARS. This is what the Nenwood Service Center will tell you.

To enter the password, you must use the remote.

1-- Point the remote control to the unit.

2 -- Enter this code: 55222277 or 552222777 (depending the remote control you are using).

Try to press the numbers as fast you can. It's like texting on your phone.

You will not see any change on the screen while you are entering the number,

only when you enter the last number. Then the unit will go into standby mode.

If you make a mistake, reset the unit and start all over again.

• 
• 1 answer

See the link below.

• 
• 1 answer

A fuse blow when ever the amperage is to high for the circuit. Either there is a short (to ground or positive), the connections are corroded, wire gauge is too thin or it is the wrong fuse. Never put in a fuse larger than recommend for the circuit, it could cause a fire.

• 
• 1 answer

Im not sure if u get the opportunity to view individual manuals on the net which is doubtful but depending on the nature of what you need 2 know you could take it to either a vodafone or a samsung retailer(shop/store)

• 
• 1 answer

Blue is memory.

• 
• 1 answer

http://www.suberdave.com/USMB/95_Impreza_18l_wiring.pdf

• 
• 1 answer

You can download the instruction manual from Kenwood.com. The wiring diagram is on page 29.

• 
• 1 answer

The memory wire is blue on the Kenwood VZ907. Now I hope you can help me. I am trying to hook this same product in my vehicle. However, I cannot get past BUS-E50. What does this mean? The memory wire is blue on the Kenwood VZ907. Now I hope you can help me. I am trying to hook this same product in my vehicle. However, I cannot get past BUS-E50. What does this mean?