Lexus RX

Basic tools are required, a jack to lift the car off the ground and a jack stand to insure safety, once off the ground and supported you will need to get a socket or commonly called(lug Wrench) with 19mm or 21mm socket head depending on your lug size. It is usually easier to lift and support both sides at the same time with the car in park emergency brake set key on so the steering wheel isn't locked. Then once wheels are off you will need a 17 mm wrench/ socket to remove the brake caliper bracket. Once done you should loosen the bleeder valve with either a 8,9 or 10 mm wrench depending on the model, carefully not to get air into the system, and depress the caliper using a tool sold at any kragen or auto parts retailer for about 5 bucks. Imediatly when it bottoms out you should tighten the bleed screw to prevent any air from getting in the system. It is useful to have the master cylinder cap off so any fluid that is not needed in the system can be drained out. It also helps to leave the inner brake pad installed (clipped on) when depressing the caliper so you know when you are getting close to bottoming out the caliper. Next you will need a 13,or 14mm wrench to take the caliper apart to install your new pads. Make sure you use anti-squeak brake adheasive to prevent the loud embaressing noise when brakes are applied. It should be a free floating brake rotor that can come off using minimal force.( should slide right off). You then have your rotors measured for proper spec.s to see if they can be turned or just buy new rotors and replace as needed. (note: turning rotors at a local machine shop can save you money but can take up most of the day trying to find someone to turn them and then having them turned, also new rotors are thicker and disapates heat better allowing your brakes to last longer and are only about 10-15 bucks a side more exspensive then having them turned). Repeat the steps backwards making sure you clean all parts with brake clean to prevent squeaks. Good luck.

Behind the glove box. Instructions are in Owner's Manual. Open glove box and unhook hangars from each side of glove box door. Remove panel on the back wall of the glove box. Cabin filter is behind this panel.

The red exclamation point in a circle is the parking brake indicator.

The "bank" or head considered number two in your vehicle will be closest to the front of the vehicle. The O2/AF Sensor

labeled 1st from that bank will be between the engine and the fan assembly. Pop the hood look down between the engine and

the bumper and you should see a thick wire (several actually just wrapped to look like one) going from the right side of

the engine to the exhaust pipe. It will end at a conical sensor with a Hex base.

How to replace the tire pressure valve on lexus rx 350?

On my 2000 Sonata, it was pretty straightforward. Loosen lug bolts on wheel. Jack up the car and finish removing the wheel lug nuts, remove tire. Remove brake calipers. Two bolts. Suspend caliper to remove weight from the caliper hose. The rotor should be able to be straight pulled off. It might need some banging with a rubber mallet. Use eye protection. Make sure your parking brake is off, as the parking shoes are inside the rotor and will hold the rotor tight if on. If this is unsuccessful, there is one or two screws on the rotor that can be removed and a longer screw inserted and tightened, this will lift the rotor off of the inner hub. Don't break the screw. Slide the rotor off, then replace it with the new rotor, replace caliper and probably a new set of brake pads. Replace wheel and lug nuts, lower car to ground and finish tightening the lug nuts to torque found in owners manual.

The Lexus rear wiper blade size is a special 14" rear wiper blade that is very simple to replace once you find a replacement. Unfortunately, most stores do not stock this special rear wiper blade so please see Sources and Related Links below for more information on the wiper blade and installation videos. Once you get the wiper blade, there will also be step-by-step instructions on the packaging.

PREMIUM

The difference is in the engine 330 is bigger than 350'

opened my 2006 rx330 - read 2016 - cant figure how to access the battery going to radio shack maybe they can do it

Yes. My 91 Stanza was running poorly, poor gas milage, the speedometer works sometimes, when i hit a bump it will do the opposite - if it was working and i hit a bump it will stop working until i hit another bump. I resolder each solder at the back of it and problem solved. Better gas milage.

The 2009 Lexus RX-350 is 6 ft. 0.6 in. (72.6 in.)10 -way power driver seat wide.

Buy the CD from Lexus and insert it into your CD player

3 total one downstream and 2 upstream.

Take out the back seat and fold the rear section of the carpet forward. On the driver's side floor is a round metal cover with a wire harness running through. Pry off the cover (it it glued on) to reveal the pump top. Remove the wire connector. Carefully remove the orange snap-lock from the fuel line, then pry the fuel line up and off. Remove the bolts and flange holding the pump in place, then pry the pump loose and lift straight up and out. The filter is on the pump. Don't smoke while doing this.

225.00 a corner.

Try eBay for $53.00 Dollars or Toolsource.com for $15 AND change goodluck.

Lift up the rear hatch storage space lid and it's to the right of the tool kit area (you have to remove a tacky plastic cover).

2, bank1 and bank2

Premium

If you press the unlock button two times it should unlock all the doors.

The PCV valve for a 2000 Lexus rx300 is on the passenger side of the engine. It is on the valve cover near the back.

No vehicle year given... Lexus RX330 general brake light bulb lamp replacement: Purchase the correct replacement brake light bulb(s) first, before disassembling the vehicle. See sources and related links below for replacement brake light bulb information. Then consult your owner's manual for the replacement procedure. As simple as it sounds, the owner's manual is the best place to start for brake light bulb lamp replacement instructions and illustrations. You may want to consider replacing both left and right at the same time in order to keep brightness and color equal (optional).

how to change the rear sidelight on a Lexus 350

On my wife's 2003 model, the filter is located underneath the front exhaust header. It's toward the left side of the engine as you face the engine with the hood up (the passenger side of the car). I just changed it and it was the first time in forty years that I could not budge the filter! The dealer did the previous change and ran the filter down to the rim. No amount of expletives will satisfy my rage! There are instructions on the side of every filter I've ever seen - grrr!

Okay, back on task. You can see the filter from the top through the little space between the header pipes. Stock filters are black. You can also gain access to the filter from underneath the car by removing the nine or ten 10mm bolts from the panel aft of the front bumper. The two outboard bolts are different than the others so take note. My oldest son was eventually able get it loose from above but the final removal was from below. This was after an hour or so of beating on it with a hammer and 3/4 inch pipe attempting to apply force to the tangent of the circle - if you know, you know - if you don't, I'm not going to explain it here. Amazon sells at least two different type of "tripod" type filter wrenches that I will likely buy before the next change. I'll also be looking for a longer filter or a spacer in order to make access easier. Japanese designs are usually pretty good but not this time. Oh, and my ex-dealer will get the old filter and a piece of my mind too.