Mechanical Engineering

Cars can be made out of several different materials, but the majority of cars consists mainly of steel. Some may have a steel chassis, and certain body panels out of plastic or aluminium. High-end sports cars can be made out of carbon fiber to considerable extent.

ONE QUARTER 1/4 TURN Oxygen FULLY open I strongly suggest you take the AWS safety course if you ask this kind of question as you may end up killing some innocent because of your dangerous actions

It is 2.24 mm.

Iron (Iron is the only pure metal that rusts, all other metals corrode)

turbine blade angle is that angle with which,a high presseure & high temprature steam is made to empenge on it.

a graphical method to find velocity and acceleration of piston of a reciprocating engine

for better acurracy

Either too much amperage, travel speed too slow, or electrode too large for the metal thickness.

0.2 to 0.25 mm

A pretty good kind cuz mama always told me that I should try my hardest.

No. It only includes Adams/View which lets you create and simulate simple mechanisms.

This seems to be a very logical question, and there are 10 foot ceilings. Your question is valid so lets look at it.

Your equipment has a 3000kcalh load. 1 kcal = 4190 Joules, 1 btu = 1060 Joules. so 3000 x 4190 / 1060 = 11858btu. The load of your equipment is about 1 ton (12000btu) The load on the space based on 6 air changes per hour (ACH) = about another 6000btuh. A 1 1/2 ton unit should do the job, although if 70F is critical you may need to consult someone to do a full analysis.

cc is used to know about the engine size.....where as bhp tells you how much power is delivered at shaft ....it doesn't mean that larger engine size will produce more bhp than smaller one....both are different.....
cc - cubic centimetres . to measure the engine displacement .
bhp - brake horse power . to measure the power of a vehicle

t's just a way to compare engines.

The number of cc's the related to an engine, is the size of the engine. The actual size of the combustion chambers where the fuel is burned. Normally, the higher the cc's, the more fuel burned, therefore the more power.
bhp is the actual horsepower put out by the engine as built, before attached to the car, which will be lower, as a nominal amount of horsepower is needed to turn the driveshaft and drive gears.
t's just a way to compare engines.

each and every company in south Africa

the sewing machine brooklyn

By collecting gold

Im no vandal nor spammer. i only need the value of poisson ratio of cured phenolic resin(function of pressure and temperature process) for conclude a job and i dont find that information. Thank you, Lindemberg, Brazil.

search the first word

Rotary pumps are used on small scale and usually only move small amounts of liquid. They are often used to empty drums and barrels. However, the fluid that they can pump depends on the metal they are made of as some metals can rust.

reciprocating motion in an appliance is obtained from a rotating motor shaft with the aid of

To select method of grease:

The use of grease is primarily limited to the lower horse power pumps where the parameters are in size and speed of the range of rolling element bearings..Shideled bearings may limited to a maximum temperature 52(deg) ..

2.27 kips

What is the force required in N? Work in J? Power Required in W?

A vacuum in the evaporator of a refrigerating system is 284 mmHg. The barametric pressure is 742 mmHg. Determine the absolute pressure in Pa. pHg= 13596 kg/m^3. Mass of 210 kg is elevated 24.5m in 1 minute 34 seconds.

No, the perfect fuel/air ratio is 14.6 to 1. A ratio of 13 to 1 is a safe ratio for most non turbo gas engines. Turbo engines can run a 12 to 1 ratio. Chrysler's lean burn system of the 70's and 80's used a ratio of around 18 to 1 and it was horrible. No gasoline engine can run at 30 to 1.

NAICS 333912 applies to Air and Gas Compressor Manufacturing.