Oldsmobile Bravada

To remove the struts from the front of a 2002 Bravada, first, safely lift and support the vehicle on jack stands. Remove the wheel and brake components to access the strut assembly. Disconnect the strut from the steering knuckle using a socket wrench, and then remove the upper strut mounting bolts located in the engine bay. Finally, pull the strut assembly out from its mount and repeat for the opposite side.

In the Oldsmobile Bravada, the inside temperature sensor is typically located on the dashboard, near the climate control system. It may be positioned near the center or on the driver's side, depending on the model year. This sensor helps regulate the cabin's temperature by measuring the air inside the vehicle and sending information to the climate control system. If you're having issues with temperature regulation, checking the sensor's condition may be a good first step.

If the AC and heater in a 2002 Oldsmobile Bravada are only blowing air through the defrost vents and not into the cabin vents, it could be due to a malfunctioning mode door actuator. This actuator controls the airflow direction and may be stuck or broken, preventing proper airflow to the cabin. Additionally, a vacuum leak in the HVAC system can also affect the distribution of air. It's advisable to have the HVAC system inspected to determine the exact cause and resolve the issue.

To replace the thermostat on a 2000 Oldsmobile Bravada, first ensure the engine is cool and disconnect the negative battery cable. Drain the coolant from the radiator, then remove the upper radiator hose connected to the thermostat housing. Unscrew the thermostat housing, replace the old thermostat with a new one (ensuring the rubber gasket is in place), reassemble the housing, reconnect the hose, and refill the coolant before reconnecting the battery. Finally, start the engine and check for leaks.

The ECAS (Electronic Controlled Air Suspension) fuse in a 2002 Oldsmobile Bravada may keep blowing due to a short circuit in the wiring, a malfunctioning air suspension compressor, or faulty suspension control modules. Additionally, water intrusion or damaged insulation in the wiring harness can cause a short. It's important to inspect the system for any visible damage or wear and test the components involved to identify the exact cause of the issue. If the problem persists, seeking professional diagnostics is advisable.

On a 2001 Oldsmobile Bravada, the spark plugs are located on the engine's cylinder heads. Specifically, they can be found beneath the engine cover, which may need to be removed for access. The vehicle is equipped with a 4.2L inline-six engine, and the spark plugs are positioned near the ignition coils. To reach them, you may need to remove the ignition coil packs and any other components obstructing access.

To fix a Bravada stuck in park, first ensure that the brake pedal is fully depressed, as the shift interlock system requires this to allow shifting. If it still won’t move, check the brake light switch, as a malfunction can prevent shifting out of park. Inspect the shift linkage for any obstructions or damage, and if necessary, consult the vehicle’s manual for troubleshooting steps or consider seeking professional assistance.

The bolt size for the distributor cap on a 1999 Oldsmobile Bravada is typically a 7mm or 8mm bolt. However, it's important to check your vehicle's specific manual or consult a parts supplier for confirmation, as variations can occur. Always ensure you have the correct tools and specifications before proceeding with any repairs.

If the dash lights on a 1992 Oldsmobile Bravada are blinking, it could indicate a few potential issues. Common causes include a faulty battery connection, a failing alternator, or a problem with the vehicle's electrical system. It's also advisable to check for any trouble codes using an OBD-I scanner, as this can provide more insight into the underlying problem. If the issue persists, consulting a professional mechanic is recommended for a thorough diagnosis.

A 2000 Bravada not shifting out of 3rd gear could be due to several issues, including low transmission fluid levels, a malfunctioning transmission control module, or a failing shift solenoid. Additionally, problems with the throttle position sensor or issues within the transmission itself, such as worn clutches or bands, may also be contributing factors. It's essential to diagnose the specific problem with a professional mechanic to ensure proper repairs.

In a 2004 Oldsmobile Bravada, the coolant temperature sensor is typically located near the thermostat housing, which is situated on the engine block. It is usually found on the intake manifold or near the water outlet. To access it, you may need to remove some components, depending on the engine configuration. Always consult the vehicle's service manual for precise location and removal instructions.

To remove the dashboard on a 1998 Oldsmobile Bravada, first disconnect the negative battery cable to avoid any electrical issues. Next, remove any trim pieces and screws securing the dash panel, including those around the instrument cluster and center console. Carefully pry the dashboard away from the frame, ensuring all wiring harnesses and connectors are detached. Take your time to avoid damaging any clips or components during the process.

On a 1997 Oldsmobile Bravada, the orifice tube is located in the air conditioning system, specifically within the liquid line. To access it, you'll need to trace the line from the condenser to the evaporator. The orifice tube is typically found near the evaporator, often inside the engine compartment. Be sure to handle the components with care to avoid damaging the AC system.

The fuel pump relay for a 1998 Oldsmobile Bravada is located in the under-hood fuse and relay box. This box is typically found near the battery on the driver's side of the engine compartment. To identify the specific relay, refer to the diagram on the cover of the fuse box, which will indicate the position of the fuel pump relay.

Yes, you can siphon gas from a 2000 Oldsmobile Bravada, but it may require specific tools and techniques due to the vehicle's design. Many modern cars have anti-siphoning devices in their fuel tanks to prevent unauthorized fuel removal. If you decide to siphon gas, ensure you do so safely and legally, as siphoning without permission is illegal. Always take precautions to avoid spills and inhaling fumes.

In a 2000 Oldsmobile Bravada, the fuse for the license plate bulb is located in the fuse box under the dashboard on the driver's side. You'll need to remove the cover to access the fuses. Look for the fuse labeled "LPS" or "License Plate." If the fuse is blown, replacing it should restore functionality to the license plate bulb.

The 2002 Olds Bravada typically has grease fittings located on the front suspension components, such as the lower ball joints and tie rod ends. These fittings are used to lubricate the joints to ensure smooth operation and prevent wear. Check the vehicle's service manual for specific locations and maintenance recommendations, as some vehicles may have fewer or no grease fittings based on design.

In a 1997 Oldsmobile Bravada, the oil pressure switch is located on the engine block, typically near the oil filter. It is usually positioned on the driver's side, towards the rear of the engine. To access it, you may need to remove some components or use a socket wrench to unscrew it. Always ensure the engine is cool and take necessary safety precautions before attempting any repairs.

Typically a inconsistent heating in cars is caused by a low coolant level. Most heater hose takeoffs are on the top side of the engine, so if the fluid level is low the last place for the coolant to flow is through the heater hoses.

I have seen this on various makes and models. It is by far the cheapest thing to try too.

The off-road switch in a vehicle typically adjusts the vehicle's traction control system to better handle off-road driving conditions, such as mud, snow, or gravel. It may also adjust the throttle response and shift points to optimize performance off-road.

The main fuse panel for a 1997 Bravada is typically located under the hood near the engine bay. Look for a black box with a removable cover that houses the fuses and relays. It is usually labeled for easy identification.

When I went to a 100 amp service I could not find a 100 amp. breaker in stock. I used a 60 amp. breaker and have never blown it. The 200 amp you are using can handle up to 200 amps, but if you use a smaller breaker it will only handle up to that amperage. The 200 amp is usally the total amperage of all the breakers comming out of the box. You will probably never come anywhere near using 200 amps at one time.

What is the trick for removing the starter, from the engine, I have the starter unbolted but has a small compartment that stops me removing it from the engine?

Probably on the bottom of the timing cover on the front of the engine.

1-6-5-4-3-2