Oldsmobile Regency

Fitting 22-inch wheels on a 1996 Oldsmobile 98 Regency is possible, but it requires careful consideration of several factors, including wheel offset, tire size, and suspension modifications. You may need to make adjustments to avoid rubbing against the wheel wells or suspension components. It's advisable to consult with a professional or a wheel specialist to ensure proper fitment and safety.

To change the coil pack on a 1988 Oldsmobile 98 Regency, first ensure the engine is off and cool. Disconnect the negative battery cable and remove any components obstructing access to the coil pack, such as the air intake or engine cover. Unplug the electrical connector from the coil pack, then remove the mounting bolts and take out the old coil pack. Install the new coil pack by reversing these steps, ensuring all connections are secure before reconnecting the battery.

To remove and replace the radio in a 1992 Oldsmobile 98 Regency, start by disconnecting the negative battery terminal to ensure safety. Carefully remove the dash trim surrounding the radio using a trim tool or flathead screwdriver to avoid damage. Unscrew the radio mounting screws and gently pull the radio out, disconnecting the wiring harness and antenna. To install the new radio, reverse the process by connecting the wiring, securing the radio with screws, and reattaching the dash trim.

To replace the water pump on a 1988 Oldsmobile Regency, first, disconnect the negative battery cable and drain the coolant from the radiator. Remove the serpentine belt, then take off any components obstructing access to the water pump, such as the fan and shroud. Unscrew the water pump from the engine block, clean the mounting surface, and install the new pump with a new gasket. Finally, reassemble the components, refill the cooling system with coolant, and reconnect the battery.

To reset the change oil message on a 1993 Oldsmobile 98 Regency Elite, turn the ignition to the "On" position without starting the engine. Press the gas pedal three times within five seconds. This should reset the oil change indicator light. If the message persists, you may need to check your vehicle's manual for additional steps.

For a 1998 Oldsmobile Regency brake caliper, you typically need a 7/32-inch Allen wrench (hex key) to remove the caliper bolts. However, it's always best to verify with a repair manual or check the specific caliper design, as some models or variations may differ slightly in their specifications. Make sure to use the correct size to avoid stripping the bolts.

Fitting 22-inch rims on a 1996 Oldsmobile 98 Regency can be challenging due to the car's original design and suspension setup. While it's possible to install larger rims, you'll likely need to make modifications such as adjusting the wheel well, changing tire sizes, or even altering the suspension to avoid rubbing and ensure proper clearance. It's essential to consult with a professional to ensure safety and compatibility.

To adjust the trunk lid on a 1997 Oldsmobile Regency, first, inspect the hinges and latch for any visible damage or wear. Use a socket wrench to loosen the hinge bolts slightly, allowing for adjustment. Gently lift or lower the trunk lid to the desired position and tighten the bolts securely. Finally, check the alignment with the rear of the vehicle and ensure the latch engages properly when closed.

I'm unable to show pictures, but I can describe the typical order for the spark plug wires on a 1989 Oldsmobile Regency's V6 engine. Generally, the firing order for this engine is 1-2-3-4-5-6, and the wires should be connected to the coil pack in that sequence, starting from the front of the engine. It's best to consult a repair manual or diagram for your specific engine layout to ensure accuracy.

On a 1988 Oldsmobile 98 Regency Brougham with a 3.8 liter V6 engine, the ignition control module is typically located on the side of the engine block, near the distributor. It may be mounted on a bracket or directly on the engine itself. To access it, you might need to remove some components, such as the air cleaner or other nearby parts for better visibility. Always refer to the vehicle's service manual for specific details and diagrams.

To replace the fuel pump on a 1988 Oldsmobile 98 Regency, first, disconnect the negative battery cable to ensure safety. Next, relieve the fuel system pressure by removing the fuel pump fuse and starting the engine until it stalls. Then, access the fuel pump by removing the rear seat to reach the fuel tank access panel. Disconnect the fuel lines and electrical connector from the pump, unbolt it from the tank, and replace it with the new pump, reassembling everything in reverse order.

To replace the struts on a 1992 Oldsmobile 98 Regency Elite, start by safely lifting the vehicle and securing it with jack stands. Remove the wheel, then detach the strut assembly by loosening the upper strut mount bolts and the lower bolts connecting the strut to the steering knuckle. Replace the old strut with a new one, reattach the bolts, and ensure everything is tightened properly. Finally, reassemble the wheel and lower the vehicle back to the ground.

Your engine is running too lean, probably the result of either a vacuum leak or possibly a damaged EGR valve. You will damage the valves, pistons or who knows what if you don't take care of this problem immediately.

It's inside the alternator. If you haven't already done one (and evidently you haven't) it would probably be best for you to just replace the whole thing. Some special tools are required and it can get a little overwhelming for the first timer.

On the GM's that I am familiar with the fuse box is underneath the dashboard to the left of the brake pedal. It usually has a black cover with 2 finger-sized tabs. gently squeeze these toward each other (unless the cover says otherwise) and it should pull right off. If you have the owners manual it will also give you this information plus exactly here the fuse you are look for is, how many amps it is and what size it is. If you don't have the manual, some GM's abbreviate what the various fuses are for and what amps they are right on the fuse block.

I've got a 92 98 road touring and it did this and all it was, was the sending unit. It is got an end cap on it and it was broken

To replace the tension pulley on a 1998 Oldsmobile Regency, start by disconnecting the negative battery terminal to ensure safety. Use a wrench to relieve tension on the serpentine belt by turning the tensioner pulley, then remove the belt from the tension pulley. Unscrew the mounting bolts securing the tension pulley and replace it with the new one. Finally, reinstall the serpentine belt and reconnect the battery terminal.

To program the Regency Model ACT-T16K, you typically need to access its programming mode by pressing the designated buttons (often a combination of the "Mode" and "Channel" buttons) while powering on the device. Once in programming mode, you can set frequencies, privacy codes, and other parameters using the keypad. After making your adjustments, ensure to save the settings before exiting programming mode. For detailed instructions, always refer to the user manual specific to the ACT-T16K model.

Very carefully! - with mechanics tools, and you better remember how to put it back together again or take pictures or draw pictures or paint the bolts different colors and their bolt holes the same color. Your local library may have a service manual with more detailed help.

When a crowned monarch is very young or incapacitated for some reason, a regent is often appointed to handle the government until the monarch is able to rule.

you don't...this is 3800 motor with 3 coils in a pack at the front of the motor,,,no distribtor to move...the computer sets the timming...whats your problem? i have gm factory manuals on this car... yackygene

Sounds like you may have dropped something down inside of one of the heads when you had the intake off.

Is it full of fresh clean oil and a new filter????

To program a Regency R-4020 scanner, you'll need to follow these general steps: First, turn on the scanner and enter the programming mode by pressing the appropriate button (usually labeled “PROG” or “PROGRAM”). Next, use the keypad to input the frequency you want to store, and then assign it to a specific memory channel. Finally, save the frequency by pressing the designated button (often "ENTER" or "SAVE"). Consult the user manual for specific instructions and details on advanced features.