0
Remote Control Devices
A remote control device is commonly an infrared device used to control electronic devices such as televisions and DVD players. It is usually powered by AA or AAA size batteries.
2,009 Questions
How do you sync a wii remote to the console?
There's a red button inside the remote's battery compartment and another one in the SD card slot on the console (right above the eject button and below the reset button). Push the 2 red buttons simultaneously and they will sync
Codigos control universal ge modelo 24914?
necesito el codigo de un ge 24914 para programar el vcr y tv
Check online on the Samsung website, they will have manuals for their products there, Gook luck. :D
Rick3yBoBBy
Most garage door opener manufacturers adhered to new federal guidlines imposed buy the government in the early 90's to include 2 safety devices in each opener to avoid crushing injuries. Most of them use photo eyes you might notice mounted towards the bottom 6 inches of the track that the garage door rides in, ( near the floor on either side of the door). These are used to detect if there may be an obstruction in the path of a CLOSING door. IF these photo eyes cannot see each other (the beam of infra-red light between them is interupted), the opener is programmed to allow the door to close as long as someone push and holds the wall button in throughout the downward travel of the door. This forces an individual to observe the downward movement of the door, thus, hopefully preventing an injury or property damage. Usually these photo eyes will have small LED lights on them. IF both LED lights are on, this means the photo eyes can see each other, if not, try adjusting or bending the brackets until they are lined up and lights can be seen on each photo eye. This is a very common problem. It sometimes only takes a slight bump to knock them out of alignment. If this doesn't work, make sure the wiring from the photo eyes up to the opener is in tact and connected securely. Don't worry about a shock, most openers use low voltage for this system.
Answer2 A hit it right on the head. but if somehow that still does not help, sometimes check to see the sensors are not dirty or sometimes have spider webs, that also causes a problem.
These are both correct you will also have some of them having problems during the day but not at night most of the time this is caused by the sunlight shining in on the receving side. Easy fix is to swap the sensors
What is the remote code for an Auria EQ4088P in Dish?
There are no published codes for an Auria TV but here are instructions on performing a power scan in an attempt to find a code on the remote.
Power Scan
1. Turn the TV on
2. Press and hold the TV mode button for three seconds - The LED should flash
3. Press the red TV POWER button
4. Press the UP or DOWN arrow buttons on the remote (about one press per second). Stop as soon as the device turns off. - The TV should turn off
5. Press # - the remote is now addressed to the TV.
Korg pa 50 what is the program button for?
The Program button on Korg PA50 contains number of sound when you press it, it's very convenient as the Korg PA50 selected the best of sound harmony together. Hope this help
Do they have a universal remote for Karaoke machines?
no but sometimes you can find the remote sold seperatly online.
What is the code for an rca rtd325w?
I had bought an RCA universal remote to replace my lost rtd325w remote and still no luck. I can get it to operate most dvd functions, but no audio options. The original replacement remote is a whopping 35 dollars for a system I bought brand new for 99 dollars. I am going to be selling my system, and getting a different brand that does not charge a third of the product cost just for the remote control. RCA obviously does not care about the consumer, and wants to make as much money as possible. They have lost me as a customer.
It may take some searching but try these three ways:
Get in to your local Radio Shack when they aren't busy and talk to the staff. Most of the staff there have a personal interest in electronics and if you get lucky, you'll find one that may have information to help you.
Next, try telephone calls and emails to RCA. Even if they only release circuit diagrams to dealers, you might be able to talk to someone who can let you know the values of the resistors you are after.
Finally, find a forum that discusses electronic repairs and equipment. Get the right forum and there will be someone who may have detailed knowledge of the product.
Happy hunting.
Need factory override code for Panasonic cq-vd7500u?
If you are talking about resetting the id code, you must hold down the right tracking button for ten seconds. It will enter the last known code for you. Then you can go into the menu and change the id from there.
What is the att uverse remote code for a toshiba 42hm66 dlp projection tv?
I just used a Zenith code 1255 for my Toshiba HDTV and it worked! Good Luck!
Is a mpeg audio file the same as mp3?
Not necessarily. Although the most common MPEG audio format, there are also other standards, both previous to and successive to MP3. MPEG Audio Layer 1 (MP1) and MPEG Audio Layer 2 (MP2), as well MPEG-4 Part 3 could be classified as an "MPEG audio file."
Ge universal remote rc24914e and you need the code for a sony DVD player dvp-ns400d?
MANUALLY ENTERING CODES
1. Manually turn on the device (TV, VCR, DVD, etc.) you wish to
program.
2. Press and hold the CODE SEARCH/SETUP button on the remote
until the INDICATOR LIGHT lights, then release.
3. Press and release the button for the device you are programming
(TV, VCR, DVD, etc.). For AUX, press AUX then the device button
you are assigning to AUX. The INDICATOR LIGHT will blink then
remain lit.
4. Enter the three or four digit code for your device using the number
buttons in the GE Universal Remote. After your code is entered the
INDICATOR LIGHT will turn off.
5. Aim the remote at the device (TV, VCR, DVD, etc.) and press the
POWER button. Your device should turn off.
Note: If your device does not respond to the first code listed,
repeat steps with the next code. If none of the codes listed for your
device work for your device or your brand is not listed, try the Code
Search method described below.
USING CODE SEARCH FUNCTION
If your TV, VCR, DVD, etc. does not respond after you have tried all the codes
for your brand or if your brand is not listed, try searching for your codes by
following the steps below.
1. Turn on the device you wish to program.
2. Press and hold CODE SEARCH/SETUP until the INDICATOR
LIGHT lights, then release.
3. Press and release the device button for the device you are
programming (TV, VCR, DVD, etc.). The INDICATOR LIGHT will
blink once then remain lit. For AUX, press AUX then the device
button you are assigning to AUX.
4. Press and release POWER until your device turns off. Wait at least
2 seconds between each time you press POWER. Important: You
may have to press POWER up to 250 times.
5. When your device turns off press the ENTER/SAVE button. The
INDICATOR LIGHT will go off.
Adventures in Dinosaur city
