0
Tool and Die Makers
All questions concerning tool makers, die makers, mold makers and tool fitters and the work they do including the tools and equipment they use (machines such as lathes, mills, shapers, grinders, saws), as well as the necessary education and training to become one can be found here.
388 Questions
Where can one find a wiring diagram for a craftsman 10 ton log splitter?
http://www.searspartsdirect.com/partsdirect/retrieveSubComponentPartsAction.action?diagramPageId=00001&componentDescription=REPLACEMENT%20PARTS&documentId=00014546&modelNumber=833287500&productCategoryId=0729200&brandId=0247&modelName=CRAFTMAN%20ELECTRIC%20LOG%20SPLITTER&backToLink=Return%20to%20Sub%20Components
this if you make the picture bigger shows where the wires go. just not color coded . hope this helps Craig
How do the Amish make table legs without a lathe?
The Amish use lathes. What they DON'T use is electricity from the mains, unless they're renting the building their shop is in. Instead, they put a diesel engine in the shop, connect it to a driveshaft, and power the lathe from the driveshaft with leather belts. Or they drive the lathe with air or hydraulic.
A brake lathe is a metal lathe designed for truing the surfaces of automotive brake rotors which the brake pads bear upon.
resurface rotors and drums
How high should a wood lathe be off the ground?
depends on how tall you are. basically it should be high enough to where you the worker does not need to bend over from the waist straining your back nor should you should you have to reach too high stressing your shoulders.
Why feed rod is using in the engine lathe?
The feed rod transmits power from the headstock to the carriage for feeding operations.
The lead screw transmits power from the headstock to the carriage for screw thread cutting operations. On some lesser types of lathes the feed rod and the lead screw are used for both the feed and the screw cutting power transmission.
The method below is basic and will work.
(X and Z values etc have been guessed)
Or you can use Macro commands to loop and move standoff for each pass.
G0 X32.0 Z12.0 M8
G76 P000060 Q120 R.04
G76 X27.5 Z-50.0 P1250 Q200 F12.0
G0 X32.0 Z14.0
G76 P000060 Q120 R.04
G76 X27.5 Z-50.0 P1250 Q200 F12.0
G0 X32.0 Z16.0
G76 P000060 Q120 R.04
G76 X27.5 Z-50.0 P1250 Q200 F12.0
G0 X32.0 Z18.0
G76 P000060 Q120 R.04
G76 X27.5 Z-50.0 P1250 Q200 F12.0
G0 X32.0 Z20.0
G76 P000060 Q120 R.04
G76 X27.5 Z-50.0 P1250 Q200 F12.0
G0 X32.0 Z22.0
G76 P000060 Q120 R.04
G76 X27.5 Z-50.0 P1250 Q200 F12.0
Applicationsof mechanical press?
mechanical press is a machine used in cold working of metals, usually in form of thin sheet or strip.
CPM 10V is a tradename for A-11 tool steel. CPM is a registered trademark of Crucible Industries, LLC. There are many more tradenames for A-11 tool steel. ASP 2011 is a tradename for Erasteels A-11. Bohler-Uddeholms tradename for A-11 is K294. Zapp Tooling Alloys tradename for A-11 is Z A-11 PM. PM10 is a generic name used by some tool steel companies to designate A-11.
What steel is used to make a screwdriver blade?
A screwdriver head is normally made of toughened/hardened steel or chromium plated steel. Depending on the quality of the screwdriver.
What is profiling on lathe machine?
Vertical milling machine is for cutting large pieces.
The lathe cutting tool motion is perpendicular to the ground.
They are said to Karosl lathe.
The lathe is one of the engineers' most valuable tools. Coupled with a milling machine or milling head (Tri-axis lathe) there is nothing that cannot be produced from virtually any kind of material.A lathe can be used to:# Turn an ornate wooden spindle# Skim a cylinder head or other gasket-face# Put a screw-thread on a piece of metal bar# Drill a hole of almost any size in almost any material# Machine an intricate valve, collet or gudgeon# Put a screw-thread INSIDE a hole (Tap the hole)# Produce a complex component such as a cog-wheel, crown wheel or pinion# Re-bore the cylinder of an engine# Create irregular / offset flanged components of infinite complexity.# Turn-down a piece of tooling to fit a specific tool.The list is almost endless. There isn't much you cant do with a lathe, especially if it has a milling head! (Engineers wet dream!)
tracheotomy
A lathe is a machine that is used to carve wood or metal by turning it.
What is the formula to find a taper with a taper attachment on a lathe machine?
(bigger dia - smaller dia)/2*taper length
What are the parts and functions of tail stock?
Tail stock is a part of lathe ,which is used to support the lengthy job.
Repairing a lathe machine typically involves diagnosing issues such as motor failure, misalignment, or worn bearings. Common steps include inspecting and replacing damaged components, recalibrating settings, and ensuring proper lubrication. Regular maintenance, such as cleaning and tightening loose parts, can also prevent future problems. It's essential to follow manufacturer guidelines and safety protocols during repairs.
A nose end is the end of a skate board where the skateboard curves or the end of a nose on your face
